Instruction Manual for SRPC models including: 70260021-A, SRPCZG910524200CVF, 70260021-A 200W ZigBee LED Driver, 200W ZigBee LED Driver, ZigBee LED Driver, LED Driver, Driver
200W ZigBee LED Driver(Constant Voltage) 70260021-A Function introduction Important: Read All Instructions Prior to Installation AC 100-277V power input Common Anode Output( )
3 days ago — 100-240V~ 2.3A 50/60Hz. 277V~ 0.806A 50/60Hz. (277V~for North America only). NC= connect Suitable for Damp Locations (CONVIENT AUX EMPLACEMENTS HUMIDES).
Important: Read All Instructions Prior to Installation. AC 100-277V power input. Common Anode Output( ). Common Anode Output( ). CH 1:R output(-). CH 2:G output ...
File Info : application/pdf, 4 Pages, 738.13KB
DocumentDocument200W ZigBee LED Driver(Constant Voltage) emc 300MHz Important: Read All Instructions Prior to Installation Function introduction 70260021-A AC 100-277V power input Program Key: short press to switch on/off load, press and hold down to increase/decrease light intensity (AWG18-14) (0.55-0.86in) L 200W ZigBee Dimmable Driver AC INPUT N SEC: Output Voltage=24VDC FG INPUT: Irated=1x4.16A/2x4.16A/ 100-240V~ 2.3A 50/60Hz 3x2.75A/4x2.08A 85 277V~ 0.806A 50/60Hz Prated=1x100W/2x100W/ ta 45 NC (277V~for North America only) 3x66W/4x50W : >0.95@230VAC NC E493567 NC=None connect Suitable for Damp Locations (CONVIENT AUX EMPLACEMENTS HUMIDES) (AWG20-14) (0.24-0.28in) 1- 2- 3- 4- NC Prog. NC NC NC NC LED OUTPUT Common Anode Output(+) Common Anode Output(+) CH 1:R output(-) CH 2:G output(-) CH 3:B output(-) CH 4:W output(-) Note: 1) W channel can be turned on through Gateway's color temperature control interface which will mix RGB channels as 1 channel white and then make color tuning with the 4th channel white. Once turned on, the brightness of white channel will be controlled together with RGB channels. 2) W channel can be controlled separately from RGB channels through RGBW zigbee remote or touch panel's W button, please refer to their manuals. Product Data LED Channel DC Voltage Output Max. Current Voltage Tolerance Rated Power Voltage Range Frequency Range Input Power Factor (Typ.) Total Harmonic Distortion Efficiency (Typ.) AC Current (Typ.) Inrush Current (Typ.) Leakage Current Standby Power Consumption 4 12V DC Max. 8.3A/ch, ch1+ch2+ch3+ch4=16.6A ±1% 24V DC Max. 4.1A/ch, ch1+ch2+ch3+ch4=8.4A max. 200W 100-277V AC 50/60Hz > 0.98 @ 230VAC THD 15% (@ full load / 230VAC) 93% @ 230VAC full load 2.3A @ 100VAC, 1A @ 230VAC, 0.9A@277VAC Cold Start Max. 65A @ 230VAC < 0.5mA /230VAC < 1W Dimming Interface ZigBee Control Dimming Range 0.1%-100% Dimming Method Pulse Width Modulation Protection Over Current Over Temperature Yes, recovers automatically after fault condition is removed Yes, recovers automatically after fault condition is removed Working Temp. -20 ~ +45 Max. Case Temp. Environment Working Humidity Storage Temp. & Humidity Safety Standards Safety & EMC Withstand Voltage Isolation Resistance EMC Emission 85 (Ta="45") 10% ~ 95% RH non-condensing -40 ~ +80, 10% ~ 95% RH UL8750, CAN/CSA C22.2 No. 250.13-14, ENEC EN61347-1, EN61347-2-13 approved I/P-O/P: 3.75KVAC I/P-O/P: 100M Ohms / 500VDC / 25 / 70% RH EN55015, EN61000-3-2, EN61000-3-3 EMC Immunity EN61547, EN61000-4-2,3,4,5,6,8,11, surge immunity Line-Line 1KV Others MTBF 187100H, MIL-HDBK-217F @ 230VAC at full load and 25 ambient temperature · Dimmable LED driver with metal case, 4 channels 12/24VDC constant voltage output · Class 1 power supply, full isolated metal case · Built-in two-stage active PFC function, PF > 0.98, Efficiency > 93%, low standby power < 1W · Compliant with Safety Extra Low Voltage standard · Over load, over temperature protection · ZigBee RGBW LED light device based on ZigBee 3.0 protocol, supports Touchlink commissioning · Enables to control ON/OFF, light intensity and RGB color · W channel can be controlled through Gateway's color temperature control interface · W channel can be controlled separately from RGB channels through RGBW zigbee remote or touch panel's W button · Can directly pair to a compatible ZigBee remote via Touchlink · Supports zigbee green power and can bind max. 20 zigbee green power remotes · Compatible with universal ZigBee coordinator or gateway products · IP20 rating, suitable for indoor LED lighting applications · 5 years warranty Safety & Warnings · DO NOT install with power applied to the device. · DO NOT expose the device to moisture. Operation 1.Do wiring according to connection diagram correctly. 2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system. 3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network) Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will fail. Please refer to the part "Factory Reset Manually". Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as instructed by the controller. Step 3: power on the device, it will be set into network pairing mode (connected light flashes twice slowly), the network pairing mode will last until the device is added to a zigbee network. AC 100-277V input AC INPUT (AWG18-10) (0.55-0.86in) L N FG NC NC 200W ZigBee Dimmable Driver Step 4: Connected light will blink 5 times and then stay solid on, then the device will appear in your controller's menu and can be controlled through controller or hub interface. LED OUTPUT (AWG20-14) (0.24-0.28in) 1234- NC Prog. NC NC NC NC V+ V+ R- R- G- G- B- B- W- W- MAX 200W RGBW LED 4. TouchLink to a Zigbee Remote Step 1: Method 1: Short press "Prog" button (or re-power on the device) 4 times to start Touchlink commissioning immediately, 180S timeout, repeat the operation. Method 2: If the device is already added to a network, it will be set into Touchlink commissioning immediately, 180S timeout. Once timeout, re-power on the device to set it into touchlink commissioning again. Zigbee Remote < 10cm AC 100-277V input LED OUTPUT AC INPUT (AWG18-10) (0.55-0.86in) L N FG NC NC 200W ZigBee Dimmable Driver (AWG20-14) (0.24-0.28in) 1234- NC Prog. NC NC NC NC Step 4: There shall be indication on the remote for successful link and connected light will flash twice. V+ V+ R- R- G- G- B- B- W- W- MAX 200W RGBW LED Step 2: Bring the remote or touch panel within 10cm of the lighting device. Step 3: Set the remote or touch panel into Touchlink commissioning, please refer to corresponding remote or touch panel manual to learn how. Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote. 2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes. 3) For Third-Party Automation Devices, add remote and device to network first then TouchLink. 4) After TouchLink, the device can be controlled by the linked remotes. 5. Removed from a Zigbee Network through Coordinator or Hub Interface From your ZigBee controller or hub interface, choose to delete or reset the lighting device as instructed. The connected light blinks 3 times to indicate successful reset. 6. Factory Reset Manually Step 1: Short press "Prog." key for 5 times continuously or re-power on the device for 5 times continuously if the "Prog." key is not accessible. AC 100-277V input LED OUTPUT AC INPUT (AWG18-10) (0.55-0.86in) L N FG NC NC 200W ZigBee Dimmable Driver (AWG20-14) (0.24-0.28in) 1234- NC Prog. NC NC NC NC Step 2: Connected light will blink 3 times to indicate successful reset. V+ V+ R- R- G- G- B- B- W- W- MAX 200W RGBW LED Note: All configuration parameters will be reset after the device is reset or removed from the network. 7. Factory Reset through a Zigbee Remote (Touch Reset) Note: Make sure the device already added to a network, the remote added to the same one or not added to any network. Step 1: Re-power on the device to start TouchLink Commissioning, 180 seconds timeout, repeat the operation. Zigbee Remote < 10cm AC 100-277V input LED OUTPUT AC INPUT (AWG18-10) (0.55-0.86in) L N FG NC NC 200W ZigBee Dimmable Driver (AWG20-14) (0.24-0.28in) 1234- NC Prog. NC NC NC NC Step 4: There shall be indication on the remote and connected light flashes 3 times for successful reset. V+ V+ R- R- G- G- B- B- W- W- MAX 200W RGBW LED Step 2: Bring the remote or touch panel within 10cm of the lighting device. Step 3: Set the remote or touch panel into Touch Reset procedure to reset the device, please refer to corresponding remote or touch panel manual to learn how. 8. Find and Bind Mode Step 1: Short press "Prog." button 3 times (Or re-power on the device (initiator node) 3 times) to start Find and Bind mode (connected light flashes slowly) to find and bind target node, 180 seconds timeout, repeat the operation. 11. Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator Required) Step 1: Short press "Prog." button 4 times (Or re-power on the device 4 times) to enable the device to setup a zigbee network (connected light flashes twice) to discover and add other devices, 180 seconds timeout, repeat the operation. Zigbee Remote AC 100-277V input LED OUTPUT AC INPUT (AWG18-10) (0.55-0.86in) L N FG NC NC 200W ZigBee Dimmable Driver (AWG20-14) (0.24-0.28in) 1234- NC Prog. NC NC NC NC V+ V+ R- R- G- G- B- B- W- W- MAX 200W RGBW LED Step 2: Set the remote or touch panel (target node) into find and bind mode, and enable it to find and bind initiator, please refer to corresponding remote or touch panel manual. Step 3: There shall be indication on the remote or touch panel that it bind the device successfully and can control it then. 9. Learning to a Zigbee Green Power Remote Step 1: Short press "Prog." button 4 times (Or re-power on the device 4 times) to start Learning mode (connected light flashes twice), 180 seconds timeout, repeat the operation. Zigbee Green Power Remote AC 100-277V input LED OUTPUT AC INPUT (AWG18-10) (0.55-0.86in) L N FG NC NC 200W ZigBee Dimmable Driver (AWG20-14) (0.24-0.28in) 1234- NC Prog. NC NC NC NC Step 2: Set the green power remote into Learning mode, please refer to its manual. Step 3: Connected light will flash twice to indicate successful learning. Then the remote can control the device. V+ V+ R- R- G- G- B- B- W- W- MAX 200W RGBW LED Note: Each device can learn to max. 20 zigbee green power remote. 10. Delete Learning to a Zigbee Green Power Remote Step 1: Short press "Prog." button 3 times (Or re-power on the device 3 times) to start delete Learning mode (connected light flashes slowly), 180 seconds timeout, repeat the operation. Zigbee Green Power Remote AC 100-277V input LED OUTPUT AC INPUT (AWG18-10) (0.55-0.86in) L N FG NC NC 200W ZigBee Dimmable Driver (AWG20-14) (0.24-0.28in) 1234- NC Prog. NC NC NC NC Step 3: Connected light will flash 4 times to indicate successful deleting. V+ V+ R- R- G- G- B- B- W- W- MAX 200W RGBW LED Step 2: Set the paired green power remote into Learning mode, please refer to its manual. Zigbee Remote AC 100-277V input LED OUTPUT AC INPUT (AWG18-10) (0.55-0.86in) L N FG NC NC 200W ZigBee Dimmable Driver (AWG20-14) (0.24-0.28in) 1234- NC Prog. NC NC NC NC V+ V+ R- R- G- G- B- B- W- W- MAX 200W RGBW LED < 10cm TouchLink Zigbee Lighting Device Step 2: Set another device or remote or touch panel into network pairing mode and pair to the network, refer to their manuals. Step 3: Pair more devices and remotes to the network as you would like, refer to their manuals. Step 4: Bind the added devices and remotes through Touchlink so that the devices can be controlled by the remotes, refer to their manuals. Note: 1) Each added device can link and be controlled by max. 30 added remotes. 2) Each added remote can link and control max. 30 added devices. 12. ZigBee Clusters the device supports are as follows: Input Clusters · 0x0000: Basic · 0x0003: Identify · 0x0004: Groups · 0x0005: Scenes · 0x0008: Level Control · 0x0300: Color Control · 0x0b05: Diagnostics Output Clusters · 0x0019: OTA · 0x0006: On/off 13. OTA The device supports firmware updating through OTA, and will acquire new firmware from zigbee controller or hub every 10 minutes automatically. Wiring diagram AC 100-277V input LED OUTPUT (AWG18-14) (0.55-0.86in) L 200W ZigBee Dimmable Driver AC INPUT N SEC: Output Voltage=24VDC FG INPUT: Irated=1x4.16A/2x4.16A/ 100-240V~ 2.3A 50/60Hz 3x2.75A/4x2.08A 85 277V~ 0.806A 50/60Hz Prated=1x100W/2x100W/ ta 45 NC (277V~for North America only) 3x66W/4x50W : >0.95@230VAC NC E493567 NC=None connect Suitable for Damp Locations (CONVIENT AUX EMPLACEMENTS HUMIDES) (AWG20-14) (0.24-0.28in) 1- 2- 3- 4- NC Prog. NC NC NC NC V+ V+ R- R- G- G- B- B- W- W- MAX 200W RGBW LED Product Dimension 330mm 79mm 39mm 270mm 261.7mm 62mm 79mm 39mm