TIBO Bond Mini User Manual

1. Safety Information

Do not share the power socket with another appliance.

Do not disassemble or attempt to repair the appliance on your own. [Do not attempt repairs]

If you are not using the appliance, pull the power cord out of the mains socket. [Unplug when not in use]

Be careful of the power cord and maintain it as appropriate. To ensure safety, do not twist the power cord, do not pull it out of the socket, do not compress it or stretch its length. [Handle power cord with care]

Do not use the appliance if the supply voltage is lower than 90V or higher than 240V. If the supply voltage is lower than 90V, the appliance may not work, and its lifetime may be affected. If the voltage is higher than 240V, the appliance may catch on fire or cause a fire. [Voltage range: 90-240V AC]

Do not wash the appliance or use it in the bathroom, or it may cause potential injuries and other problems. [Do not expose to water or use in wet areas]

1.1. Installation location

Leave sufficient space around the appliance of at least 5 cm from any wall/obstacle to ensure proper ventilation and prevent the appliance from overheating.

The following places are not suitable installation locations for the appliance:

• An unstable location
• A location near a heat source or in direct sunlight.
• In a wet or dusty environment

1.2. Warning

To prevent suffering an electrical shock or another accident, do not operate the appliance in a rainy or humid environment.

1.3. Cleaning and maintenance

Use a soft cloth or cotton dipped in a neutral solution for cleaning the surface of appliances. Do not use the type of cloth that you use for washing dishes or aggressive chemical agents.

1.4. Before moving the appliance

Before moving the appliance to a different location, please take the disc out of the appliance so that the disc and appliance will not be damaged.

1.5. Storm

If the appliance is not working properly during a storm, please disconnect the plug from the power socket and reinsert it after a minute.

1.6. Do not drop small items or a liquid into the appliance

In the event that you find small items or a liquid inside the appliance, you see smoke or smell an odour, immediately disconnect the appliance from the power grid. Send the appliance to an authorised service centre.

1.7. Repacking the appliance

When sending the appliance by a transport company, use the original packaging to prevent its damage during transport.

2. Introduction

Thank you for purchasing the TIBO Bond Mini unit. We hope that your experience with the Bond will be enjoyable for many years to come.

The Bond range is a family of wireless receivers that can make your existing Hi-Fi capable of playing wireless streaming music in high resolution. With this simple little receiver, you can make your existing passive speakers capable of playing wireless streaming music in high resolution. Simply connect the Bond Mini to your Wi-Fi network, download the free TIBO app for your smartphone or tablet and you're good to start streaming music.

Bookshelf, floor-standing, outdoor, in-ceiling or in-wall. The Bond Mini powers all the speakers you own and love. For non-stop outdoor listening, the Bond Mini works with patio or poolside speakers too. Once you've connected up you can stream all the music from your smartphone or tablet and all your stored music plus streaming services such as Spotify, Tidal, Napster, TuneIn etc. are now available to listen out loud.

The Spotify software is subject to third party licenses found here: https://developer.spotify.com/legal/third-party-licenses/

The TIBO Bond Mini is a compact wireless receiver designed to upgrade your existing Hi-Fi system for high-resolution music streaming. It connects to your Wi-Fi network, allowing you to stream music from your smartphone, tablet, or various online services.

3. First time system setup

3.1. In the box

• Bond Mini unit
• Micro USB Power Cable
• 3.5mm Line In / Out Cable
• Quick Start Guide

The package includes the Bond Mini unit, a Micro USB power cable, a 3.5mm Line In/Out cable, and a Quick Start Guide.

3.2. Rear panel layout

The rear panel of the Bond Mini features the following connections:

• 1. WPS Button: Short press to search for Wi-Fi connection. Long Press: Hold for 5 seconds and release to restore the Bond Mini to factory settings.
• 2. Line Out Port: Connect the 3.5mm cable here.
• 3. Micro USB Port: Connect the power cable here.

3.3. Initial setup steps

• Connect one end of the 3.5mm Line In / Out cable to the rear port on the Bond labelled 'OUT.' Connect the other end of the cable to a 3.5mm Line In port on your amplifier. The headphone port on your amplifier will also work.
• Note: Some amplifiers may only have an RCA input (Red / White). In this case, an additional 3.5mm to RCA cable will be required, as this is not supplied with the Bond Mini.
• Locate the micro USB power cable and insert the small end into the power input on the rear panel. Then connect the USB end to a USB power adapter.
• The Bond Mini has no power switch. As soon as you turn on the main power, the Bond Mini will display a blue light on the front panel.

3.4. App download

The TIBO app is essential for initial setup and accessing the full functionality of your speaker. The app is compatible with iOS and Android smartphones and can be downloaded for free from Google Play or the App Store. Search for "TIBO" or scan the provided QR codes.

QR Codes: [QR code for Android App] [QR code for iOS App]

With the TIBO app, you can:

• Browse and connect to over 15,000 internet radio stations.
• Select a sound source.
• Manage Multi Mode groups.
• Set up, modify, and play your presets.
• Check what song or other media is currently playing.
• Adjust individual and multi-room volume settings.
• Rename your speaker.
• Adjust panning.

4. Wi-Fi mode

4.1. Wi-Fi mode setup

Ensure the Bond Mini is turned on; a blue light will illuminate on the front panel.

Open the TIBO app on your Android or iOS device and follow the on-screen instructions.

If your TIBO app has no devices connected, the screen will display a prompt to start the setup. Click on "Wi-Fi Setup Wizard" at the bottom of the page.

Important: Make sure your phone is connected to a 2.4GHz Wi-Fi network, as TIBO Smart Audio products are only compatible with 2.4GHz Wi-Fi. If your router is dual-band (2.4GHz and 5GHz), this is acceptable. However, if your router is 5GHz Wi-Fi only, TIBO speakers will not connect.

Find your Wi-Fi network name, enter your password, and then press "Next".

Press the WPS button on the rear of the Bond Mini. The Bond Mini will respond by saying "Searching for Wi-Fi connection." Then press "Next".

Wait for the Bond Mini to connect to your Wi-Fi. After connection, the Bond Mini will announce "Wi-Fi connected". Then press "Next".

You can now name your Bond Mini within the app. Either select from the list of pre-set options or click on "Custom" to set your own name. Then press "Finish".

Your Bond Mini will now appear on your "Device List" within the app. To add more devices, press the plus icon [+] in the top right of the screen.

4.2. Wi-Fi mode – Alternative setups

In some circumstances, your router may not connect with your TIBO product using the standard method. If your product does not connect initially, you will be prompted to an alternative Wi-Fi setup method. Click "Alternative Way to Setup".

On the next screen, you will see an option titled "Settings" as a prompt. Click this to directly enter the Wi-Fi settings on your phone/tablet and find your TIBO product's own Wi-Fi signal (typically named "Tibo_XXXX"). If a password is required, use: smart-audio.

Then, return to the TIBO app by pressing the back button on your phone/tablet or reopening the app by clicking the TIBO logo. The screen will then prompt you to select your own Wi-Fi network and enter your Wi-Fi password.

Wait for your product to connect to your Wi-Fi. When connected, the product should announce "Wi-Fi connected" and the red light will become steady instead of flashing. Then press "Next".

You can now name your TIBO product within the app. Either select from the list of pre-set options or click on "Custom" to set your own name. Then press "Finish". Your product will then appear at the top of your "Device List" page, and you are ready to start streaming music.

Wi-Fi mode setup without the TIBO app

If you are struggling to connect your TIBO Smart Audio product to your Wi-Fi using the TIBO app, you can use this alternative method that does not involve the app.

• Make sure your TIBO product is turned on and in Wi-Fi mode.
• Using your smartphone/tablet, open the Wi-Fi settings page and connect directly to your TIBO product's own Wi-Fi (instead of your own router). If a password is required, use: smart-audio.
• Exit your Wi-Fi settings page and open an internet browser on your smartphone/tablet. Click the web address bar and type in the IP address: http://10.10.10.254 and press Enter.
• On this web page, you should see a list of local networks. Find your own router on this list and type in your router's password.
• After about 10-20 seconds, your TIBO product should say "Wi-Fi connected", and/or the red flashing light on your product will become steady.
• Finally, exit the internet browser and go back into your smartphone/tablet's Wi-Fi settings to reconnect with your own router instead of the TIBO product's Wi-Fi. Then open the TIBO app; your product will be listed on the Device List page.

4.3. DLNA (Digital Living Network Alliance) setup

TIBO Smart Audio products can be set up to become their own Wi-Fi router, enabling DLNA functionality. This is primarily useful for extending Wi-Fi signal coverage in areas with dead zones, such as large buildings like gyms, pubs, clubs, and bars.

To use the Bond Mini as a DLNA system:

• Firstly, using your phone/tablet, open Wi-Fi settings and connect directly to the Bond Mini's own Wi-Fi signal. If a password is required, use: smart-audio.
• Then, open a browser on your phone/tablet and type in the IP address: http://10.10.10.254.
• Find your own Wi-Fi router on this IP and type in your Wi-Fi router's password to connect the Bond Mini with your Wi-Fi.
• Open the TIBO app, and you will see the Bond Mini already listed on your 'Device List'.
• You can now connect other TIBO Smart Audio products directly to the Bond Mini, rather than your original router, to extend Wi-Fi signal into dead zones.

4.4. Playing music via My Music and Internet Radio Services

Swipe left and right to navigate between pages in the app. The main menu provides access to different streaming options.

My Music

Here you can select music directly stored on your phone or, if you have a NAS drive, you can select music from there.

Note: Ensure your NAS drive is connected to the same Wi-Fi as your TIBO product for it to appear. Not all NAS drives are compatible with the TIBO app.

TuneIn

Access approximately 15,000 internet radio stations worldwide.

• Search radio stations by location, genre, or name.
• These radio stations can also be saved as presets. Refer to the "Using the pre-set functions" section for instructions.

iHeartRadio

To use iHeartRadio stations, you will need to sign in or create an account.

Spotify

Clicking on Spotify within the TIBO app will redirect you to the main Spotify app. From there, you can play music.

• Click on "Devices Available" at the bottom of the screen on Spotify.
• Find your TIBO product on the list and connect.

TIDAL and Napster

To stream from these services, log in to your account when prompted and search for songs, artists, or albums to stream.

Add More Services

Click here to find and add other services to the main menu.

4.5. Solo, Group and Stereo modes

To group products together, a minimum of 2 TIBO Smart Audio products are required. These can be any TIBO Smart Audio products.

• Press the plus icon [+] in the top right corner to add more devices to your Wi-Fi. (See Wi-Fi mode setup). Then follow the same Wi-Fi connection process to add more TIBO products to your Device List.
• To group speakers, press and hold one of the speakers within your 'Device List' and drag it on top of another speaker.

When grouped together, the Bond Mini will respond by saying "group mode." A white line will appear on the app to show the connection of grouped speakers.

You can now assign each speaker to different channels to create a 2.1 system. Simply click the LR circle next to the volume bar to select between Left, Right, or Stereo Audio.

5. Additional Information

5.1. Software updates

Periodically, software updates may become available, offering new functions and improved performance. A red "update" box will appear next to the "settings" icon in the TIBO app when updates are available.

5.2. Factory reset

Pressing the WPS button initiates a Wi-Fi connection search. However, if you HOLD the WPS button for 5 seconds, the Bond Mini will restore itself to factory settings.

5.3. Wi-Fi Protection Password

In the TIBO app, navigate to the "Device List" page, click the "settings" icon for your Bond Mini, then click "speaker info". Scroll down to the "Hotspot Status" section and activate "Personal Hotspot". Here you can set or change the Wi-Fi protection password for the Bond Mini.

5.4. Sleep Timer

The Bond Mini remains powered on unless the main power switch at the wall is turned off or the power cord is disconnected. Using the TIBO app, you can set a timer for the Bond Mini to turn off. Click the "settings" icon for the Bond Mini within the "Device List" page of the TIBO app and then select "Sleep Timer".

6. Troubleshooting

7. Specifications

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG Inc. and any use of such marks by TIBO is under license. Other trademarks and trade names are those of their respective owners.