Verkada CD22-HW Indoor Dome Camera Installation Guide

Installation Guide for Verkada models including: CD22-HW Indoor Dome Camera, CD22-HW, Indoor Dome Camera, Dome Camera, Camera

VERKADA CD22 (01) PDF MANUAL - Manual-Hub.com

File Info : application/pdf, 11 Pages, 2.29MB

VERKADA CD22 (01)

Install Guide
CD22 CD32 CD42 CD52 Indoor Dome Camera

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401 sales@verkada.com
https://manual-hub.com/

Document
Document Details
V1.7 (20230901)
(V1.0 first published 20211208)
Firmware
Firmware version can be verified on Verkada Command command.verkada.com.
Product Models
This install guide pertains to models CD22-HW, CD32-HW, CD42-HW, CD52-HW.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

All specifications are subject to change without notice

sales@verkada.com

https://manual-hub.com/

Introduction
What's in the box

Indoor Camera

Mount plate (Attached to camera)

Mounting template

3 M4 x 50mm machine screws, wing nuts, and washers

4 M4 x 25mm PH2 wall screws

4 Wall anchors

T10 Security Torx screwdriver

What you'll need
A working Internet connection 802.3af Power over Ethernet (PoE)
switch, or a PoE injector. For operation below -20° C, use 802.3at PoE. A smartphone or laptop A #2 Phillips screwdriver or power drill with a #2 Phillips driver bit 1/4 inch (6.5mm) drill bit for wall anchors 1/8 inch (3mm) drill bit for pilot holes A Cat5 or Cat6 Ethernet cable with a 0.2-0.25 inch outside diameter (5-6.5mm)

Placement
Mount the camera on a wall or ceiling. Try to keep the camera 8 to 10 feet above the ground.
For best night vision, avoid overhangs or obstructions. These may reflect the camera's IR illumination and reduce the image clarity in night mode.
Connect
For easy registration and setup, scan the QR code on the product.
If you prefer to manually register your product, please proceed to: verkada.com/start

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

All specifications are subject to change without notice

sales@verkada.com

https://manual-hub.com/

Introduction
LED Behaviors
Regular operation
Solid Orange Camera is on and booting up.
Flashing Orange Camera is updating firmware.
Solid Blue Camera is running, connected, and recording data.
Flashing Blue Generic network error. Contact support.

Status LED

Network errors
The LED will flash in a specific order, depending on the error state. You will see 1 blue flash, followed by a number of orange flashes.
1 Blue, 1 Orange Camera is connected with PoE, but unable to connect to the Switch.
1 Blue, 2 Orange Camera has not received an IP address.
1 Blue, 3 Orange Camera is not able reach the configured Gateway.
1 Blue, 4 Orange Camera has detected duplicate IP addresses on the LAN.

Example of 1 Blue, 5 Orange flash sequence
1 Blue, 5 Orange Camera is not able to resolve Verkada hostnames.
1 Blue, 6 Orange Camera is not able to receive a response from the NTP Server.
1 Blue, 7 Orange Camera is not able to certify the SSL connection, likely due to SSL inspection.
1 Blue, 8 Orange Verkada endpoints are not reachable after boot up.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

All specifications are subject to change without notice

sales@verkada.com

https://manual-hub.com/

Installation
Assembly 1/2

PbluebabselekNuenoetptilecthoempprloetteincgtivtehefilfminaaldshteepreodf

to the clear installation.

Use the provided T10 Security Torx security screwdriver to loosen the screws and lift the cover.

Connect the camera to an 802.3af/at Power over Ethernet port on your network.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

All specifications are subject to change without notice

sales@verkada.com

https://manual-hub.com/

Installation
Assembly 2/2

Twhilel tsutrantNuboslutLeeEDtowinilldtiucranteortahnegceatmoeinradiicsaatcettivhee.

camera has power. The LED See additional LED states and

definitions under LED Behavior.

Gently pull the cable through the through-hole so it has some slack, but will not interfere with the top cover.

Pulling the Ethernet cable too tight will strain the cable which may impact data performance.

Too much slack in the Ethernet cable may create top cover installation issues.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

All specifications are subject to change without notice

sales@verkada.com

https://manual-hub.com/

Installation
Mounting

lUoNsoeosetthneethperosvcidreewdsTa10nsdelcifut rtihtye

torx security screwdriver cover. To remove the

mount plate, loosen the mount plate screws and twist

the camera counter-clockwise. Lift the camera vertically

off the base plate and set aside.

2. Use the provided mounting template to mark wall mount holes. For a junction box mount, use the mounting template to determine the correct hole pattern.

3. For a solid material like wood or metal, drill 1/8 inch pilot holes. Drive mounting screws directly into the pilot holes.

4. For drywall, drill 1/4 inch holes. Insert plastic anchors into holes and drive mounting screws into anchors.

5. To secure the camera, place it over the mount plate screws and twist counter-clockwise. Tighten the mount plate screws with a Phillips screwdriver.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

All specifications are subject to change without notice

sales@verkada.com

https://manual-hub.com/

Installation
Adjust
AcodnjufsirtmyNoimourtaecgaemoerireanttoattihoen.desired viewing angle. Use the online stream to
Image can be flipped 180° online in Command. Default image orientation is indicated by markings on the lens face. Video orientation is also adjustable from within the Verkada application.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

All specifications are subject to change without notice

sales@verkada.com

https://manual-hub.com/

Installation
Secure

AwfittehrtphoeNsbiotaiotseneipnlgatyeoaurncdapmlaecrea

correctly, align the top shell security holes the top shell back into its original position.

Tighten the security screws using the provided T10 security torx screwdriver.

Remove plastic film after top cover is secured.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

All specifications are subject to change without notice

sales@verkada.com

https://manual-hub.com/

Appendix
CD22 CD32 CD42 CD52 Compliance

Caution

1. Maintenance and repair work must always be carried out by qualified technical personnel. Disconnect power from the unit when performing a maintenance task.
2. Wiring methods used for the connection of the equipment to earth shall be in accordance with the National Electrical Code, ANSI/NFPA 70, and the Canadian Electrical Code, Part 1, CSA C22.1.
3. The product must be installed and protected in a location that is not easily accessible and is away from impacts or heavy vibration.
4. The device is only to be connected to PoE networks without routing to outside plants. 5. If powered by a power adapter, the adapter should be properly grounded. 6. Please contact certified dealers for power adapters.

PoE Adapter

To reduce potential safety issues, only use the PoE adapter provided with the product, a replacement PoE adapter provided by Verkada, or a PoE adapter purchased as an accessory from Verkada.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

All specifications are subject to change without notice

sales@verkada.com

https://manual-hub.com/

Appendix
Support
Thank you for purchasing this Verkada product. If for any reason you're experiencing issues or need assistance, please contact our 24/7 Technical Support Team immediately.
Sincerely, The Verkada Team verkada.com/support

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

All specifications are subject to change without notice

sales@verkada.com

https://manual-hub.com/

References