Videos - Pyramid Time Systems
User Guide for PYRAMID models including: PSDLAUBKK, Automated Swipe Card Time Clock System, Swipe Card Time Clock System, Card Time Clock System, Clock System, PSDLAUBKK
PSDLAUBKK TimeTrax™ Elite Swipe Time Clock, Ethernet - Pyramid Time Systems
Connect Terminal Using Time Clock Connect either end of RJ45 cable into “ETHERNET” port located on the back of time clock terminal. Connect power supply into “POWER” port located in compartment on back of terminal.
File Info : application/pdf, 2 Pages, 5.72MB
DocumentDocumentUser Guide available at pyramidtimesystems.com/resources/user-guides Guía del usuario disponible en pyramidtimesystems.com/resources/user-guides Guide de l'utilisateur disponible à pyramidtimesystems.com/resources/user-guides Contents PSDLAUBKK Terminal PSDLAUBKK Quick Start Guide Mounting Hardware TOP TimeTraxTM Swipe Cards (50) Part #41302 & #41303 Ethernet Cable (CAT5) Power Supply Security Bracket & Key What you will need. Tape Measure Pencil Phillips Head Screw Driver Power Drill (Optional) PSDLAUBKK 9700 Quick Start Guide Send us an email pyramidtimesystems.com customersupport@ptitime.com s I2259 Rev. M Chat online Call us 888.479.7264 EXT 1 Copyright © 2020 Pyramid Time Systems. All rights reserved. Software Requirements Operating System & Single User installation RAM: 8GB or higher Processor: 1.7 GHz minimum TimeTraxTM Time & Attendance software should not be installed on server PC's.Pyramid Time Systems does not support the use of TimeTraxTM software on a server PC. Windows 8 or above All Windows updates must be installed TM prior to software installation Must be Primary Admin to install software. English Regional settings & hardware input in English IMPORTANT: Please write down serial # located on back of terminal before mounting. Write your serial # here: SAMPLE Connect Terminal 2 1 3 6 5 1 Connect either end of RJ45 cable into "ETHERNET" port located on the back of time clock terminal. 2 Connect power supply into "POWER" port located in compartment on back of terminal. 3 Route the cables through channel at base of terminal. 4 Mount terminal (see instructions below). 5 Plug free end of RJ45 cable into a DHCP network jack, router or switch. 6 Plug power supply into outlet. Download TimeTraxTM Software To download your Time and Attendance software follow the steps below. 1 In your web browser type in the following URL: pyramidtimesystems.com/V5 2 Scroll down to the "DESCRIPTION" tab and follow the instructions. 3 Once your software is installed, use the default login info. Login ID:ADMIN Password:PTI 4 Once logged in to the software, navigate to CLOCK/HARDWARE MANAGER. Make sure your clock says ONLINE, under STATUS. Put a check mark in the ACTIVE box to claim your clock and allow for automatic punch downloads. If your device is OFFLINE, please check your connections. TimeTraxTM Instructional Videos Follow the instructions below to view our setup videos. 1 In your web browser type in the following URL: pyramidtimesystems.com/resources/videos 2 Scroll down to TimeTrax Time and Attendance Software and start with the HARDWARE MANAGER video. Mount Terminal 4 TOP To mount terminal. · Install mounting bracket. Use mounting screws and drill template provided. "TOP" is engraved to ensure bracket is oriented correctly and the tabs face upwards. · Additional holes are provided if mounting onto an electrical box. · Push terminal onto mounting bracket aligning four tabs on bracket with four matching slots on back of terminal. Be sure to write down the terminal serial number before mounting. Slide terminal downward until locking tab clicks into place. When properly mounted, terminal cannot be removed from the bracket without using the included wall bracket release key to disengage locking tab. · Cables may be rooted through channel at base of terminal or by drilling a hole in the rectan gular section of the mounting bracket and through the wall for concealing cables. To detach terminal. · Insert key (tab facing outward) into narrow slot located on bottom of terminal to right of cable access cutout. · Push key all the way up into slot. Key will slide easily until last ½ inch until some resistance from locking tab is felt. · With key fully pushed into slot, slide the terminal up and off mounting bracket. Using Time Clock Swipe card in the swipe channel from top to bottom with magnetic strip on the right hand side. If employee card number is successfully read, the time clock terminal will beep and the card number will be displayed briefly on terminal screen. Technical Support and Warranty info at pyramidtimesystems.com/support/warranty-and-return/