Fórum Intelbras - Índice
intelbras.com.br/suporte-tecnico
intelbras.com.br
User Guide for intelbras models including: IVA 5040 AT, IVA 5080 AT, Articulated active sensors
Mar 24, 2021 — IVA 5040 AT and IVA 5080 AT. Articulated active sensors. Congratulations, you have just purchased a product with Intelbras quality and safety.
File Info : application/pdf, 15 Pages, 2.96MB
DocumentDocumentUser manual IVA 5040 AT IVA 5080 AT IVA 5040 AT and IVA 5080 AT Articulated active sensors Congratulations, you have just purchased a product with Intelbras quality and safety. The IVA 5040 AT and IVA 5080 AT sensors were developed with the objective of offering an effective infrared barrier, combined with a high flexibility of installation and alignment through its articulation system. Both models have more configurations to meet the demands of installation scenarios, always maintaining the quality of Intelbras products. Read the information carefully for the correct use of both sensor models. Care and safety » Install the sensor in a stable location that is not subject to flickering. » Install the transmitter and receiver so that they are aligned; » LGPD - General Law for the Protection of Personal Data: Intelbras does not access, transfer, capture, or perform any other type of treatment of personal data from this product. » Do not install the sensor in locations where beam obstruction may occur. Check that there are no plants, branches or other objects that could obstruct the sensor beam; » Do not install the receiver and transmitter with the lens facing the sun; X X X X » Size the power supply and power cord correctly; » Do not leave the cable exposed to the sun, rain or moisture; » Do not install the sensor above the recommended distance; » Always check that there are no reflections on clear and polished surfaces, which can prevent the sensor from triggering. Do walking tests in different positions along the barrier to make sure there are no reflections; » Use the sealing rubber correctly to prevent insects from entering the sensor; » To clean the outside of the sensor, use a cloth moistened with water; never use chemicals. » For installation of stacked sensors, the maximum number of sensors installed is 3 (three), they must be in different and crossed frequency channels, as shown in the following image. TXTX CACHNAANLNE3L 3 RXRX CACNHAANLNE2L 2 TXTX CACNHAANLNE1L 1 RRX X CCHAANNNAELL 33 TTX X CCHAANNNAELL 22 RRX X CCHAANNNAELL 11 X RRXX CACNHAANLNE1L 1 TTXX CCAHNAANNLE3L 3 RRXX CACHNAANLNE2L 2 TTXX CACHNAANLNE1L 1 TXTX CCHANNNAELL11 RXRX CCHAANNNAELL33 TXTX CCHANNNAELL22 RXRX CCHAANNNAELL11 » For installing sensors in perimeters, always follow the sensor layout below: RRXX CACHNAANLNE3L 3 TTX X CCHAANNANELL 22 RRXX CACHNAANNLEL22 TTXX CACHNAANLNE1L 1 PPeEriRÍmMeEtTerRO TTX X CCHAANNNAELL 22 RRX X CCHAANNNAEL 11 TTXX CACHNAANLNE3L 3 RRX X CCHAANNNAELL22 » In order to avoid interference between sensors that may be on the same channel, respect the side protection distance as specified below: RRXX CACHNAANNLEL11 RXRX CCHAANNNAELL1 1 TTXX CACNHAANLNE1L 1 TTX X CCHAANNNAELL11 DistânciSaidedproetectPiornodisttaencçeão Lateral » For the IVA 5040 AT sensor, follow the protection distances below: Distance between TX and RX 20 m 40 m 60 m1 Side Protection Distance (DPL) Vertical Protection Distance (DPV) >2 m >3 m >4 m Maximum stacking of 3 sensors » For the IVA 5080 AT sensor, follow the protection distances below: Distance between TX and RX 40 m 80 m 120 m1 Side Protection Distance (DPL) Vertical Protection Distance (DPV) >3 m > 5 m >7 m Maximum stacking of 3 sensors 1 Distance to indoor area only. That is, for both IVA 5040 AT and IVA 5080 AT, the side protection distance is always the distance between RX and TX divided by 20 (twenty) plus 1 (one) meter. DPL> Distance between TX and RX + 1 [m] 20 ! In outdoor environments with a high rate of fog or rain, install the sensors at a maximum of 50% of the distance specified for each model, in order to avoid false alarms. Summary 1. Technical specifications 7 2. Product 8 3. Installation 9 4. Troubleshooting 13 Warranty term 14 1. Technical specifications Model Number of beams Power supply voltage Consumption current (TX + RX) Frequency channels Maximum protection distance External Indoor Alarm output Alarm Time Response time Detection method Alignment indication Trigger indication Horizontal Alignment Vertical Alignment Solar filter for outdoor environments Operating temperature IP protection grade Dimensions (B × W × D) Weight IVA 5040 AT IVA 5080 AT 1 2 10 ~ 24 Vdc / Vac (without polarity) 65 mA 3 channels, frequencies 1, 2 and 3 40 m 80 m 60 m 120 m NA and NF output 2 A @ 24 Vdc 2s 50 ms to 1s, adjustable by trimpot Block 1 beam Block 2 simultaneous beams green LED red LED 360° 180° Yes -10° to +55°C IP55 8 × 24 × 7 cm 8 × 35 × 7 cm 0.4 KG 0.7 kg 7 2. Product MainPGCriaanbbciiinnpeeattle IVAIV5A 0508800ATAT FronFtrToacnomtvapelra ASrtuicpuolarttieng Articusulápvpeolrt 336600°° 118800°° TTXX RRXX IVAIVA55004400AT AT 336600°° 181800°° TTXX RRXX 33 44 11 11 1. Power 2. Alarm output 3. Frequency channels 4. LED On TX 5. Response time adjustment 6. LEDs alignment and trigger RX TEMPO 55 RESPOSTA - + 3 4 2 5 1 33 44 33 6 11 11 3 - +5 1 55 33 66 22 1 Alimentação 2 Saída de Alarme 3 Canais de Frequência 4 LED On TX 5 Ajuste do Tempo de Resposta 22 6 LEDS Alinhamento e Disparo RX 8 3. Installation 1. For security reasons, it is necessary to open the sensors to identify which is the transmitter and which is the receiver. Here's how to open the sensor cabinet and perform the necessary identification: IVAIVA5500880 A0T AT ReRmemoovvaeothpeasrcarfeuwso coRneRfmoeormmveoetvhame faorovntiatmmcoevpneartoafsriosnhndotiwacnal dinothe na figufigruar,e,uutsielizthee aopbeenrintugrloacalotecdaalitztaheda brottteominofef trhioerfrodnat ctoavmerptoafafrcoilintattael para facilitarermaovraelmoção TEMPO RESPOSTA - + 3 4 2 5 1 IVA I5VA0504400ATAT 3 - +5 1 IdenTtXiafnicdaRXçiãdeontiTficXatioen RX 2. After identification, run the cable as shown in the following image to connect it to the terminal block: Vista pRoeasrtevireiwor SVidisetavielwateral CCabbloe 9 3. Secure the sensors in the installation position following the recommendations below: » Do not install the sensor upside down. » Orient yourself by the positioning arrows located on the articulated sensor support. DDoowwn n DDoowwnn 4. Turn on the power on the receiver and transmitter board (10 ~ 24 Vdc / Vac - no polarity). After that, connect the wires from the alarm output to the zone input of your alarm panel: TTrRaAnNsSmMiItStSeOrR 10 ~ 24 RREeCcEePivTOerR 10 ~ 24 CM NF NA FONTE GND +12V ConCeoctnanr eàcCt ethnetral alarmdecoAnlatrrmolepsanel 5. Configure the frequency channel using the FREQ jumper. For the sensor to function correctly, the transmitter (TX) and receiver (RX) must be on the same frequency channel: Frequency channels FFRreEqQ. 1 2 3 Position 1 - Frequency channel 1 (factory default) Position 2 - Frequency Channel 2 Position 3 - Frequency Channel 3 10 6. Perform the Response Time setting. Response time is the time that the infrared barrier must be interrupted to trigger. This setting is only relevant to the receiver: 550000mms s 75075m0mss 44 33 22 225500msms X 11 ss 55 ++ 11 5500mms s -- The factory default response time is 50 ms, ie Position 1. To facilitate the association of the response time of the sensor with the interruption speed of the infrared beams, refer to the following table: Response time 50ms 250ms 500ms 750ms 1 s Detection Speed Intense running Moderate running Light running Walking Light walk 7. The quality of the sensor alignment is identified by the status of the Green LED on the receiver (RX). To obtain a satisfactory alignment, which will avoid false or unwanted triggering, the alignment must be optimal - only green LED on; Green LED (RX) Turned Off Slow flashing Fast flashing Turned On Alignment quality Beam interrupted or misaligned1 Poor alignment Poor Alignment Optimal alignment Alarm output (Red LED) ON OFF OFF OFF Probability of false alarm Null (unaligned beam) High Lowest 1 After a period of 30 minutes, without the infrared barrier being interrupted, the Alignment Quality indication LED will be automatically turned off for energy saving. The moment the infrared barrier is broken again, this LED will return to the normal Alignment Quality display state. ! Perform walking tests at various points on the barrier to make sure that there is no reflection from the infrared beams on the floor, wall or reflective objects. If reflection is found, it will be necessary to change the installation position of the sensor. 11 8. After making the configuration, tighten the screws for fixing the sensor position on both the receiver and the transmitter, as shown in the following figure: PHaroarfizuosnotadleafdixjuasçtãmoent attaching asjucrsetwe horizontal PaLroacfkuinsog dsceretwravamento PaVreartfiucsaol addejufsixtmaçeãnot attaching ajsucsretewvertical 9. To close the sensor follow the steps below: 1. Place the sealing rubber in the passage of the wires in the TX and RX. (Fig.1) 2. Place the front cover, attach the upper lock first and then the lower lock. (Fig.2) 3. Place the screw on the front cover. (Fig.3) STouTppraelovrcaiokr GCaabbinineette BorraScehaalindge vedaçRãuobber 1Fig. 1 FrontFTcraoomvnetparal LSTiadretaelovrcaakssis TBroatvtoams Infelorciokrses 2Fig. 2 ParafusoFtroanmt cpoavefrroscnretwal 3Fig. 3 12 4. Troubleshooting Follow the steps outlined below to troubleshoot your sensor: 1. Check that the installation distance is within the specified. In environments with a high rate of rain or fog, it is recommended that the installation distance be 50% of the maximum distance for outdoor environments; 2. Check the installation wiring and that the supply voltage in the TX and RX is between 10 and 24 Vdc / Vac; 3. Check that both TX and RX are on the same frequency channel, which is selected via the FREQ jumper; 4. Check that the Response Timesetting, which controls the response time from 50ms to 1s, is in accordance with the speed expected to cross the infrared beam; 5. Redo the alignment procedure; 6. Perform the detection test and confirm that there are no reflections. 7. Your infrared barrier sensor will be working! 13 Warranty term It is established that this warranty is granted upon the following conditions: Client's name: Client's signature: Invoice number: Date of purchase: Model: Retailer: Serial number: 1. All the parts, pieces and components of the product are guaranteed against possible manufacturing defects, which may arise, for the term of 1 (one) year - this being 90 (ninety) days of legal warranty and 9 (nine) months' contractual warranty , counting from the date of purchase of the product by the Consumer, as appears in the product purchase bill of sale, which is an integral part of this Term throughout the domestic territory. This contractual warranty includes the free exchange of parts, pieces and components which have a manufacturing defect, including the expenses with labor used in this repair. If there is no manufacturing defect, but defect(s) arising from misuse, the Consumer shall bear these expenses. 2. The installation of the product shall be executed in accordance with the Product Manual and/or Installation Guide. If your product requires the installation and configuration by a qualified technician, seek a suitable specialized professional, the costs of these services not being included in the product amount. 3. Having perceived the defect, the Consumer shall immediately contact the nearest Authorized Service which appears in the report offered by the manufacturer they are the only ones authorized to examine and remedy the defect during the warranty term foreseen herein. If this is not respected, this warranty shall lose its validity, as it shall be characterized as product infringement. 4. If the Consumer requests home service, it shall contact the nearest Authorized Service to inquire about the technical visit rate. If it is necessary to remove the product, the ensuing expenses, such as those of transportation and insurance of the taking and return of the product, shall be the Consumer's responsibility. 5. The warranty shall lose its validity totally in the occurrence of any of the following cases: a) if the defect is not one of manufacture, but is caused by the Consumer or by third parties foreign to the manufacturer; b) if the damage to the product arises from accidents, disasters, agents of nature (lightning, floods, landslides, etc.), humidity, voltage in the electrical network (excess voltage caused by accidents or excessive fluctuations in the network), installation/use in disagreement with the user's manual or arising from natural wear of the parts, pieces and components; c) if the product has undergone effects of a chemical, electromagnetic, electrical or animal (insects, etc.) nature; d) if the serial number of the product has been falsified or erased; e) if the appliance has been infringed. 6. This warranty does not cover loss of data; therefore, it is advisable that if it is the case of the product, the Consumer makes a backup regularly of the data which appears in the product. 7. Intelbras is not responsible for the installation of this product, or for possible attempts at fraud and/or sabotage in its products. Maintain the updates of the software and applications used up-to-date, if it is the case, as well as the network protection required for defense against hackers. The equipment is guaranteed against defects in its usual conditions of use, it being important to bear in mind that, as it is electronic equipment, it Is not free of fraud and scams which may interfere with its correct functioning. 8. After its useful life, the product must be delivered to an authorized Intelbras service center or directly disposed of in an environmentally appropriate manner to avoid environmental and health impacts. If you prefer, the battery, as well as other unused Intelbras brand electronics, can be disposed of at any Green Eletron collection point (waste management facility to which we are associated). If you have any questions about the reverse logistics process, please contact us at (48) 21060006 or 0800 704 2767 (Monday to Friday 8am to 8pm and Saturdays 8am to 6pm) or via -mail support@intelbras.com.br. These being the conditions of this complementary Warranty Term, Intelbras S/A reserves the right to alter the general, technical and esthetic features of its products without prior notice. The manufacturing process of this product is not covered by the requirements of ISO 14001. All the images of this manual are illustrative. 14 Customer Support: (48) 2106 0006 Forum: forum.intelbras.com.br Support via chat: intelbras.com.br/suporte-tecnico Support via e-mail: suporte@intelbras.com.br Customer Service: 0800 7042767 Where to buy? Who installs it? 0800 7245115 Imported to Brazil by: Intelbras S/A Indústria de Telecomunicação Eletrônica Brasileira Rodovia SC 281, km 4,5 Sertão do Maruim São José/SC 88122-001 CNPJ 82.901.000/0014-41 www.intelbras.com.br 01.21 Made in China