14pcs RGBW 4in1 Par Light User Manual

Technical Parameters

LED Display

Description of the LED display panel with numbered components:

• 1: Menu
• 2: Up
• 3: Down
• 4: Enter
• 5: Display
• 6: DMX in
• 7: DMX Out
• 8: Fuse
• 9: Power

Diagram Description: A visual representation of the LED display panel showing four buttons (1-4) and a display screen, followed by three connectors labeled 5 through 9.

Unpacking Instructions

Upon receiving the device, unpack it and check that the contents are complete and intact. Notify the carrier immediately if it shows damage, and keep all packing materials for safe transportation of the device.

Contents include:

• 1 power cord
• 1 remote control
• 2 handles
• 1 lamp
• 1 instruction manual
• 2 knobs

Safety Instructions and Operating Instructions

1. After plugging in the power and turning on the switch, the light may show "rst" indicating it is resetting; do not operate during this time.
2. Must be plugged into a grounded electrical outlet for indoor use only.
3. Do not expose the device to rain or humidity to avoid fire or electric shock. Keep the device at least 50cm away from the ground. Ensure ventilation slots are unblocked and no flammable objects are near the device.
4. Disconnect the device from the power supply before performing any operation or maintenance. The ambient temperature should not exceed 40°C, and the maximum temperature should not exceed 45°C.
5. In case of failure, stop the equipment immediately and do not attempt self-repair. Improper maintenance can result in damage and malfunction. Contact technical support. Use only original spare parts and ensure the power cord is not clogged or damaged.
6. Lamps are for decorative purposes only, not suitable for ordinary household lighting.
7. To replace the fuse: Remove the device from the power supply. Remove the fuse holder with a screwdriver. Remove the blown fuse and replace it with a fuse of the same characteristics.
8. WARNING: If the fuse continues to blow after replacement, stop using the device. For further instructions, contact Seller Support. Continued use may cause serious damage.

CAUTION: DO NOT OPEN THE HOUSING. SHOCK HAZARD.

Please read this manual carefully before operating this product.

Further Safety Instructions

9. Secure the equipment using the screw holes on the brackets. Ensure the equipment is firmly fixed to prevent vibration and movement during operation. Always check that the supporting structure is strong enough to withstand at least 10 times the weight of the equipment.
10. The equipment must be fixed by professionals in places out of reach of people, and no one should pass underneath it during operation.
11. CAUTION: There is a danger of explosion if the battery is improperly placed. Replace only with the same or equivalent types.
12. Warning about remote control batteries: Used batteries should not be thrown away with household waste. They must be collected at a separate collection point for recycling. Improper battery replacement can lead to explosion. Keep new and used batteries out of the reach of children. If the battery compartment is not properly closed, stop using it and keep it out of children's reach. WARNING: The supplied remote control contains button cells which, if swallowed, can cause severe internal burns or even death within 2 hours.
13. If you have any doubts about whether a battery has been swallowed or introduced into other parts of the body, contact your doctor immediately.
14. Before cleaning the device, disconnect it from the power source if connected. Do not use harsh cleaners. Wipe off dust or dirt with a clean cloth. The manufacturer is not responsible for damage caused by incorrect handling, improper use, or wear and tear.
15. Technical modifications are reserved.
16. End of life of the product: This symbol [recycle-symbol] indicates that this product should not be thrown into household waste in European Community countries. To protect the environment and human health, waste should be recycled responsibly to support the sustainable reuse of resources. To recycle used appliances, go to an appliance collection center or contact the dealer where you purchased the product. They will ensure the ecological recycling of the product.

Remote Control Operation

To control the light by remote, unplug the DMX cable and set Remote Control to ON. To control the device via the menu, set the remote to OFF.

Diagram Description: Four views of the par light fixture, labeled 1 through 4, showing front, side, rear, and angled perspectives.

Startup Steps for Various Modes

1. Automatic mode: Press "MENU" to find "Au01" and press "ENTER". Use the "Up" or "Down" key to select "Au09" or "Au10", and press "ENTER".
2. Sound mode: Press "MENU" to find "Au01" and press "ENTER". Use "Up" or "Down" to select "So01" or "So02", and press "ENTER".

Console Mode and Master-Slave Mode

DMX Connection: DMX out to No. 1 fixture dmx in; No. 1 fixture dmx out to No. 2 fixture dmx in.

Address Setting: Press "menu" to find "addr", press "enter", display "a001". Press "Up" or "Down" to select the console value.

Master-slave setting: Lamp No. 1 is set to self-propelled or voice-activated function according to the startup mode. Lamps 2, 3, 4**** are set to DMX512 mode. The DMX address code is 001.

Diagram Description: Three diagrams illustrating DMX daisy-chain connections between fixtures, labeled 1, 2, and 3.

Remote Control Functions

Diagram Description: An illustration of the remote control with various buttons.

• ON/OFF: Standby Switch
• Strobe: Go to strobe mode
• DMX: Go to DMX mode
• Auto: Go to Auto mode
• Jump: Go to Jump mode
• MENU: Go to menu mode
• Flash: Turn to stroboscopic mode
• Sound: Turn to voice control mode
• RED: Go to red mode
• GREEN: Go to green mode
• BLUE: Go to blue mode
• AMBER: Go to warm white mode
• CAYN: Go to cold white mode
• ROSEO: Go to purple mode
• WHITE: Turn to white light mode
• Up/Down: Adjust the value of DMX/jump/flash mode, and adjust the sound sensitivity in sound control mode.

Function List

8 Channel Mode

4 Channel Mode

Menu Options

Compliance and Product Information

Diagram Description: Four views of the par light fixture, including a view of the rear panel showing connectors and controls. Below the diagrams are compliance marks: FC, RoHS, UKCA, CE, and a WEEE symbol [recycle-symbol].