ADAYOåé³å¤åªä½å®æ¹ç½ç«-ç§æåé ä¼è´¨çæ´»
Instruction Manual for ADAYO models including: W1BFTV4, W1BFTV4 Wireless Accessory Charger Module, Wireless Accessory Charger Module, Accessory Charger Module, Charger Module, Module
Foryou Multimedia Electronics Co., Ltd. W1BFTV4 Wireless Accessory Charger Module PUZ-W1BFTV4 PUZW1BFTV4 w1bftv4
File Info : application/pdf, 5 Pages, 490.39KB
DocumentDocumentWireless Accessory Charger Module Warning Prevent debris from rem aining on the tray, or it may affect the charging efficiency or fail to charge. Metal foreign objects (such as coins, paper clips) will inhibit the wireless charging function. Do not put metal items on the charging tray. If your phone has a metal ring, it may affect charging. Do not put inflammables and explosives on the charging tray. The charging temperature range is - 40~58. Beyond this range, it will enter temperature protection. In order to avoid mutual influence, do not put the remote control key on the charging tray during charging. This product is designed for assem bly before the vehicle leaves the factory,Installation by professional workers is necessary. Do not put the card with chip (such as bank card, highway toll card, etc.) on the wireless charging tray, or it may cause degaussing damage to the card. Please confirm that your mobile phone supports wireless charging. +CAN Power turn ON first, Put the mobile phone screen upward and place it in the center of the tray to charge the mobile phone. The car screen display wireless charging status when the mobile phone start charging. WPT output param eters: 110~ 205kHz,10.72 dBuA/ m @10m Matters Needing Attention Although the wireless charging can be installed on the back of your mobile phone, you may have the function of wireless charging. However, due to the uneven quality of such products in the market, we are not sure whether they match our wireless chargers. Therefore, we do not recommend that you install the wireless charging receiver back sticker and use it on Only one mobile phone can be charged at a time, and the maximum charging power is this vehicle, and we are not responsible for the consequences. 15W. Wireless Accessory Charger Module Model name: W1BFTV4 Input: 9-16VdcEffective voltage:12-16Vdc, Output: 15W Max Brand: ADAYO FCC STATEMENT: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliancecould void the user's authority to operate the equipment. Exposure to radio frequency energy: The radiated output power of this device meets the limits of FCC radio frequency exposurelimits. This device should be operated with a minimum separation distance of 20cm (8 inches)between the equipment and a person's body. NOTE: This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residential installation. This equipment generatesuses and can radiate radio frequency energy and, if not installed and used in accordance withthe instructions, may cause harmful interference to radio communications. However, there isno guarantee that Wireless Accessory Charger Module interference will not occur in a particular installation. lf this equipment doescause harmful interference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct the interference byone or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiveris connected. -Consult the dealer or an experienced radio/TV technician for help. IC STATEMENT: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Exposure to radio frequency energy: The radiated output power of this device meets the limits of ISED Canada radio frequencyexposure limits. This device should be operated with a minimum separation distance of 20cm(8 inches)between the equipment and a person's body. Wireless Accessory Charger Module Le présent appareil est conforme aux CNR d'ISDE Canada applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et(2) l'appareil doit accepter tout brouillage radioélectrique subi, méme si le brouillage estsusceptible d'en compromettre le fonctionnement. L'exposition à l'énergie radiofréquence: La puissance de sortie rayonné de cet appareil est conforme aux limites de la lSDE Canadalimites d'exposition aux fréquences radio. Cet appareil doit être utilisé avec une distanceminimale de séparation de 20cm entre (8 pouces) l'appareil et le corps d'une personne. CE compliance statement Foryou Multimedia Electronics Co., Ltd. declares that this product is in compliance with the essentiarequirements and other relevant provisions of Directive 2014/53/EU.For the full RED DoC file, Please download it as follow web: www.AdayoMe.com Wireless Accessory Charger Module Product dist ance from t he human body :45cm. Inst allat ion mode and met hod: Screw inst allat ion, first inst all t he WACM on the bracket using screws, and then install the bracket on the back of the storage box under the center control of the car using screws. Specific available installation location: the back of the storage box under t he car cent er cont rol. Application scenario: Place the mobile phone flat above the storage box where t he WACM is locat ed for wireless charging. Manufacture Company Name:Foryou Multimedia Electronics Co., Ltd. Address:No.1, North Shangxia Road, Dongjiang Hi-tech Industry Park, Huizhou, Guangdong, P.R.China