Genkinno P1 SE Robotic Pool Cleaner User Manual

1. Introduction

This user manual provides instructions for the Genkinno P1 SE robotic pool cleaner. For further assistance or information, please contact Genkinno Customer Service via email at support@genkinno.com or visit their website at www.genkinno.com. You can also find them on Facebook at @genkinno.

2. Warnings and Cautions

2.1 Warnings

• Only use accessories recommended or sold by the manufacturer.
• This model is designed for swimming pools with a flat floor only.
• Do not allow children to ride on or play with the cleaner.
• Use only the original and authorized power adapter.
• The charging adapter must be connected to a leakage-protected socket when charging.
• Do not operate the cleaner when people or animals are in the pool.
• While charging, the cleaner should be uncovered and kept in a cool place to prevent damage from overheating.
• Only certified professionals can disassemble the sealed driving kit.
• Do not operate the cleaner while the pool filter is running.
• Oil sealant for the servo contains grease, which can cause water pollution if exposed.
• If storing the cleaner for an extended period, charge it every three months to maintain battery life between 40%-60%. Use only the original adapter. Failure to charge for extended periods can lead to over-discharge and damage.
• Do not use or store the cleaner near any heat source.
• Do not pierce the cleaner's shell with sharp objects.
• Do not hammer, impact, or throw the cleaner.
• Ensure the charging socket is dry before charging.

2.2 Precautions

• Check that the wheels turn properly.
• Always clean and wash the filter tray after use.
• Turn off the cleaner during maintenance, cleaning, or when not in use.
• Store the cleaner in a cool, ventilated place away from direct sunlight.
• Due to battery limitations, the cleaner is suitable for pools up to 1614 sq. ft (150㎡). Larger pools may result in reduced cleaning effectiveness.

2.3 Water Conditions

Use the Robotic Pool Cleaner in the following water conditions:

3. In the Box

The package includes:

• 1 X Genkinno P1 SE
• 1 X Water Filter Tank (filter included)
• 1 X Charger
• 1 X User Manual
• 1 X Floating Cable
• 1 X Handle

4. Robotic Pool Cleaner Parts

4.1 Robotic Pool Cleaner Components

The robotic pool cleaner has the following parts:

• 1. Drain
• 2. Charge Input
• 3. Power Button
• 4. Battery Level LED
• 5. Function LED
• 6. Floating Cable
• 7. Handle/Antenna
• 8. Release Button
• 9. Anti-collision Rubber
• 10. Wheel

4.2 Water Filter Tank

The cleaner includes a water filter tank and a filter.

5. Using for the First Time

5.1 Charging the Cleaner

Connect the cleaner and the included charger to charge the battery. Clean the charging port before charging. The red indicator light on the adapter signifies charging, while a green light indicates the charging process is complete.

5.2 Turn on the Cleaner

Press the start button once. The cleaner will power on, and the power indicator LED will turn green.

5.3 Check the Battery Level

Green LED: The cleaner is working normally.

Red LED: The battery requires recharging.

6. Using the Robotic Pool Cleaner

6.1 Robotic Pool Cleaner Status Indicator

The cleaner features LED status indicators. Refer to the table below for status meanings:

6.2 Auto Mode

Once turned on, the cleaner defaults to Auto Mode. It will begin operating approximately 1 to 2 minutes after being placed in the pool.

6.2.1 Placing the Robotic Pool Cleaner into the pool

Release the cleaner and let it sink to the floor of the pool.

6.2.2 Path Planning

When the cleaner reaches the side of the pool, it automatically plans its next route, parallel to the previous one.

6.2.3 Power Mode Switch

The cleaner's maximum suction power of 100W activates automatically when it encounters large leaves and other debris.

6.2.4 Auto Parking

When the cleaning session is complete or the battery is low, the cleaner will park itself for easy removal.

6.2.5 Removing the Robotic Pool Cleaner from the Pool

Locate and grab the floating cable, then pull the cable to remove the cleaner from the swimming pool.

6.3 Cleaning After Use

It is highly recommended to clean the filter basket after each cleaning cycle. Follow these steps:

1. Press the button [release button].
2. Pull out the water filter tank.
3. Open the water filter tank.
4. Clean the water filter tank.
5. Take out the filter.
6. Clean the filter.

7. Off-season Storage

If the cleaner will not be used for an extended period, follow these storage steps:

• Ensure the cleaner is turned off.
• Make sure no water is left inside the cleaner.
• Thoroughly clean the filter basket and panels and reassemble them.
• Roll up the cable without kinks.
• Store the cleaner indoors, away from direct sunlight and weather elements like rain or snow.
• If storing for a long period, charge the cleaner every three months to maintain battery life between 40%-60%.

8. Frequently Asked Questions (FAQ)

1. How large of a swimming pool can be cleaned?
   Due to battery capacity limitations, the cleaner is suitable for pools up to 1614 sq. ft (150㎡). Larger pools may affect cleaning ability.
2. How deep underwater can it work?
   The floating cable is 2 meters long. For optimal performance, a maximum depth of 2 meters (approx. 6.6 feet) is recommended.
3. How do I safely remove my cleaner from the water?
   Gently pull on the floating cable to bring the cleaner to the edge of the pool and then remove it.
4. How often should I clean the filter?
   It is highly recommended to clean the filter basket after each cleaning cycle.
5. Can the P1 SE clean walls and the waterline?
   This cleaner is designed to clean the pool floor/bottom underwater. It cannot effectively clean the walls or the waterline.
6. What is the runtime of the P1 SE? How long does it take to fully charge?
   It takes approximately three hours to fully charge the cleaner using its safe fast-charge technology. A full charge provides up to two hours of use, sufficient for cleaning most pools multiple times.

9. Specifications

10. Warranty

This product has passed all quality control and safety tests in accordance with relevant laws, regulations, and safety standards.

Warranty Information

• The warranty covers 24 months (applies only to the battery and motor) from the date of original purchase.
• This warranty is void if the product has been altered, misused, or repaired by unauthorized personnel.
• The warranty covers manufacturing defects and does not cover damage resulting from mishandling by the owner.
• The order number or record must be presented for any claim or repair during the warranty period.

Genkinno Support: http://www.genkinno.com/support

Genkinno Service: For questions about this document, contact Genkinno at support@genkinno.com.

Facebook: @genkinno