Contact | Aerpro
Installation Guide for Connects2 models including: FP8473K, Steering Wheel Control Interface for Ford Vehicles
instruction manual is based on documented data and research. The manufacturer of this product cannot be held responsible for any changes made to the.
Nov 10, 2020 —
C T 2 3 F D 6 6 I N S T A L L A T I O N G U I D E S T E P O N E Firstly, use a panel removal tool to remove both of the fans and trim panel from each
File Info : application/pdf, 8 Pages, 1.60MB
DocumentDocumentFP8473K Steering Wheel Control Interface for Ford Vehicles i ii iii iv v vi vii viii ix i. USB Retention (Female) ii. Car Connector (24 Pin) iii. Car Connector (54 Pin) iv. ISO Connector (16 Pin) v. Flying Wires vi. Yellow RCA -Camera Retention vii. Red/White RCA -AUX Retention viii. USB Retention (Male) ix.Interface Box APPLICATION Note: Application data is subject to change at any time Ford Ranger 2019 - UP For US Vehicles with SYNC3 OEM systems (small display) FEATURES ·Retains Factory Steering Wheel Control Functionality ·Retains Phone Buttons ·Retains USB and AUX Inputs ·Retains Reversing Camera ·Supports Voice Assistant (with software update via SWCREFLASHER) ·Provides Speed Pulse, Park Brake, Reverse Gear & Power Antenna Outputs DISCLAIMER The information provided in this document is subject to change without notice due to manufacturer changes and/or improvements to the product/s. This instruction manual is based on documented data and research. The manufacturer of this product cannot be held responsible for any changes made to the vehicle by the manufacturer or damages that may occur through the installation of this product in accordance with the steps outlined herein. PRIOR TO INSTALLATION Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources. Please ensure that the correct tools are used during the installation to avoid damage to the vehicle or product. Connects2 can not be held responsible for the installation of this product. WIRING KEY IN WIRING HARNESS Purple Right Rear Speaker + Purple/Black Right Rear Speaker - Green Left Rear Speaker + Green/Black Left Rear Speaker - Grey Right Front Speaker + Grey/Black Right Front Speaker - White Left Front Speaker + White/Black Left Front Speaker - Yellow Black Red Orange ADDITIONAL CONNECTIONS Light Green Park Brake Pink Speed Pulse Purple/White Reverse Gear Blue/White Power Antenna (RCA) Red/White Connect to Head Unit AUX In R/L (RCA) Yellow Connect to Head Unit Camera Input USB Retention (Male) Connect to Head Unit USB Female USB Retention (Female) Connect to Vehicle Permanent 12V Ground Ignition 12V Illumination STEERING WHEEL CONTROL FUNCTIONALITY The following diagram, though based on careful research, is an example only Individual steering wheel control configurations may differ. 1 3 OK 2 4 Steering wheel 1 1. Volume + 2. Volume - 3. Track - 5 4. Track + 5. Source 8 6 VOL 7 9 10 Steering wheel 2 1. Volume + 2. Volume - 3. Voice Assistant* 4. Source 5. Track +(Short Press) Hang Up 11 (Long Press) 6. Track -(Short Press) Pick Up (Long Press) *Visit www.connects2.com for more information on how to download the SWC software update. Note: a reflasher tool is also required (Part No: SWCREFLASHER) 2 INSTALLATION GUIDE See wiring diagram on Pg.4 for more information Before installing the interface, the factory stereo must be removed and disconnected. To do this, please consult the vehicle owners manual/handbook or contact a fitting professional. A stereo connection (patch) lead is also required for the installation of this interface (supplied separately). Please ensure that you have the correct lead before proceeding. For universal patch leads, prepare the wiring loops in accordance with the instruction manual supplied with the product before installation. 1. Connect the 12 Pin connector from the stereo connection (patch) lead to the interface box 2. Connect the opposite end of the stereo connection (patch) lead to the steering wheel control input on the back of the aftermarket stereo NOTE: This may be a 3.5mm jack connector or a wired input depending on the brand of aftermarket stereo being fitted. Please consult the aftermarket stereo installation manual for further information on where to make the connection ! IMPORTANT: THIS STEP MUST BE COMPLETED BEFORE CONNECTING POWER TO THE INTERFACE. FAILURE TO DO SO MAY RESULT IN A LACK OF FUNCTIONALITY AND THE NEED TO REINSTALL THE PRODUCT 3. Connect the 14 Pin connector from the supplied wiring loom to the interface box 4. Connect the power/speaker ISO connector (16 pin) from the interface to the power/speaker ISO connector from the aftermarket stereo. NOTE: For aftermarket stereos which do not have an ISO connector, please see "Wiring Key" on Pg.2 for information on which wires to connect. Some interfaces may also have additional flying wires which can be connected to the vehicle to support various features ie. parking brake trigger, reverse gear and speed pulse. Details of these can be found under Additional Connections. 5. Connect the 24 pin and 54 pin vehicle specific connectors on the supplied harness to the corresponding connectors from the vehicle 6. Make additional connections to retain the OEM reversing camera (yellow RCA), AUX input (red/white RCA) and USB input (USB retention harness) if the vehicle is equipped. 7. Test stereo and steering wheel control functionality for correct operation before reassembling the vehicle dashboard. If steering wheel control functions are unresponsive, please uninstall the interface and wiring and reinstall carefully in accordance with the above steps. For further help and support, please contact us directly at https://aerpro.com/contact and fill out a support ticket with the full details of your issue. 3 WIRING DIAGRAM Connect to vehicle USB Retention Lead Connect to aftermarket stereo Vehicle Specific Connectors [24 Pin & 54 Pin] Connect to corresponding connector from vehicle Male ISO Connector Connect to aftermarket stereo Flying Wires Purple/White -Reverse Gear Lt. Green -Park Brake Pink -Speed Pulse Blue/ White -Power Antenna White/Red RCA Connectors (AUX) Connect to aftermarket stereo Yellow RCA Connector (Camera) Connect to aftermarket stereo Main Wiring Loom Connector [14 Pin] Connect to Interface Box Interface Box Stereo Connection (Patch) Lead Connector [12 Pin] Connect to Interface Box Note: Must be connected first, before power connection is made to the interface 4 DOUBLE DIN FITTING KIT FORD RANGER, EVEREST2015> (Flat Black. Not for Vehicles with SYNC3 8" Touchscreen) Tools Required:- - - - - - - - - - - - - - - - - - · Panel Removal Tool/s · Screwdriver/s DISCLAIMER This instruction booklet is based on carefully documented data and research. Connects2 cannot be held responsible for discrepancies/inconsistencies that may occur due to automobile manufacturing changes, options, or damage that may occur in the vehicle during the installation of components while using this booklet Need help with your installation? Visit https://aerpro.com/contact CONNECTS2 LTD CT23FD66 INSTA LLA TIO N GUIDE STEP ONE Firstly, use a panel removal tool to remove both of the fans and trim panel from each side of the head unit STEP TWO Next, remove the panels underneath the A/C controls by hand, followed by the panel situated between the head unit and A/C controls STEP THREE With the panels removed, use a screwdriver to remove the five screws holding the fascia panel in place STEP FOUR Once the fascia panel is free, disconnect all wiring to the panel and remove the panel CONNECTS2 LTD 2 CT23FD66 INSTA LLA TIO N GUIDE STEP FIVE Unscrew the eight screws holding the head unit and top display in place STEP SIX Once the head unit and top display are free, disconnect all wiring to both parts and remove STEP SEVEN Take the OEM fascia panel and remove all eighteen screws located on the back (circled) STEP EIGHT Remove the back of the panel and disconnect the wire which leads from the top board to the A/C panel to reveal a screw. Remove this and the three other screws on the panel to detach the A/C controls from the rest of the panel CONNECTS2 LTD 3 CT23FD66 INSTA LLA TIO N GUIDE STEP NINE Insert the new trim piece into the opening in the new fascia panel. Screw the fascia panel to the A/C controls (using the four screws removed in Step Eight) and refit the back of the panel (using the eighteen screws removed in Step Seven) [NB: At this point, a Connects2 CTSFO0l 8.2 interface can be connected to retain steering wheel control functionality] STEP TEN Attach both of the brackets to the aftermarket head unit, using the fasciapanel as a guide. Once satisfied with the fit, screw the head unit into the dash STEP ELEVEN Next, reconnect all connections to the fascia panel and air conditioning assembly and clip into place around the head unit STEP TWELVE Reattach all remaining trim panels to c omplete your installation of the FP8473K Double DIN Fascia Kit CONNECTS2 LTD 4