Furrion
Instruction Manual for FURRION models including: FACW12PA-BL, Single Zone Premium Wall Thermostat
8 Operation are 5 available modes (AUTO, COOL, HEAT, FAN and DRY) for you to select. See the following tables for detailed information of each mode. NOTE: The HEAT mode is only available after the furnace is enabled. AUTO MODE
Before operating your new product, please read these instructions carefully. This instruction manual contains information for safe use, installation and ...
File Info : application/pdf, 20 Pages, 486.31KB
DocumentDocumentSingle Zone Premium Wall Thermostat
Instruction Manual
Model: FACW12PA-BL
Welcome
Thank you for purchasing this Furrion® Single Zone Premium Wall Thermostat. Before operating your new product, please read these instructions carefully. This instruction manual contains information for safe use, installation and maintenance of the product. Please keep this instruction manual in a safe place for future reference. This will ensure safe use and reduce the risk of injury. Be sure to pass on this manual to new owners of this product. The manufacturer does not accept responsibility for any damages due to not observing these instructions. If you have any further questions regarding our products, please contact us at support@furrion.com
1
Contents
Welcome ............................................................................................ 1 Contents ............................................................................................ 2 About your Thermostat...................................................................... 3
Product Features.....................................................................................................3 Control Buttons .......................................................................................................3 LCD Icons ................................................................................................................4
Installation ........................................................................................ 5
What's in the Box ....................................................................................................5 Thermostat Installation ..........................................................................................5
Operation........................................................................................... 7
Turn On/Off the Thermostat....................................................................................7 Temperature Format...............................................................................................7 Operation Mode.......................................................................................................7 Set the Temperature ...............................................................................................9 Set the Fan Speed ...................................................................................................10 Mood Light...............................................................................................................10 Sleep Mode..............................................................................................................10
Special Features................................................................................ 11
Auto Fan ..................................................................................................................11 Compressor Time Delay..........................................................................................11 LCD Error Code .......................................................................................................11
Wiring Diagram ................................................................................. 12 Specifications .................................................................................... 13 Warranty............................................................................................ 14
2
About your Thermostat
Product Features
Your Single Zone LCD thermostat is equipped with a liquid crystal display (LCD) to indicate the temperature set-point in Fahrenheit(°F)/Centigrade(°C) and fan speed. It is also equipped with LCD to indicate the system available operation modes. NOTE: The available operation modes will be different depending on the system installed in your RV. Liquid Crystal Display and Mode Indicators Auto Fan Room Temperature Display Fahrenheit(°F)/Centigrade(°C) Display Sleep Mode LED Mood Light
Control Buttons
Press to increase the temperature set-point
Press to change the color of mood light
Press to select Fan Speed
Press to decrease the temperature set-point
Press to select SLEEP mode
Press once to turn on. Press repeatedly to select mode
3
About your Thermostat
LCD Icons
Operation Mode
Room Temperature or Error Code
Fan Speed
4
Installation
What's in the Box
Make sure you have all the following items included in the packaging. If any item is damaged or missing, contact your dealer. Thermostat x 1 Instruction Manual x 1 Warranty Card x 1 Self-tapping Screw x 2
Thermostat Installation
1. Select a suitable location that is not under direct influence from light, sun or other heat sources.
2. Rotate the thermostat cover counterclockwise and pull out the base plate. (Fig. 1)
Fig. 2
Thermostat Cables
4. Fix the base plate on the wall using 2 screws. (Fig. 3) NOTE: Make sure the base plate is not covering the hole and squeezing the thermostat cables.
Fig. 3
Thermostat Cables
Fig. 1
3. Use the base plate as a template and drill a hole on the vehicle wall. Extend the four wire cables from the cutout area. Refer to the cable tag label for each cable definition. (Fig. 2)
5
Installation
5. Connect the cables to thermostat. Rotate the thermostat clockwise until it clips into place. (Fig. 4 and Fig. 5)
Fig. 4
Thermostat cables
Fig. 5
6
Operation
Your Furrion wall thermostat has been preprogrammed with factory default settings. Review the settings below and adjust to your comfort level.
FACTORY DEFAULT SETTINGS
HEATING
68ºF / 20ºC
COOLING
72ºF / 22ºC
FAN SPEED
AUTO
MODE
AUTO
FURNACE DIFFERENTIAL 2ºF
Turn On/Off the Thermostat
Temperature Format
Simultaneously press both and buttons for 3 seconds to toggle the temperature format between Centigrade and Fahrenheit. NOTE: ºF indicates Fahrenheit and ºC indicates Centigrade.
Operation Mode
To turn On
Press and hold the button for 3 seconds to turn on the thermostat. The thermostat LCD will be illuminated and the factory settings will be displayed on the LCD for first time use. NOTE: The LCD will display the last setting if you have changed the parameters.
To turn Off
Press and hold button for 3 seconds to turn off the thermostat. Only the current room temperature will be displayed on the LCD.
7
After the thermostat is turned on, press the button repeatedly to toggle through the available modes. The activated mode icon and temperature set-point will be displayed on the LCD. The thermostat will transmit the last selected operation mode command to the control box after 2 seconds without any operation.
Depending on the system installed, there
Operation
are 5 available modes (AUTO, COOL, HEAT, FAN and DRY) for you to select. See the following tables for detailed information of each mode. NOTE: The HEAT mode is only available after the furnace is enabled.
AUTO MODE
The system will changeover between COOL and HEAT mode according to the room temperature. For example, when the room temperature is below 68ºF (20ºC), the system will operate in HEAT mode. In contrast, when the room temperature is above 77ºF (25ºC), the system will operate in COOL mode. It operates the Dry Mode in comfort temperature between 68ºF (20ºC) to 77ºF (25ºC).
The AUTO icon and the current temperature set-point displays on the LCD.
COOL MODE
The system will cycle the compressor on and off based on
the room temperature and the
temperature set-point.
The fan will be turned on after the compressor is running.
There are 4 fan speed selections in this mode.
The fan operates continuously at
Low low speed and the
icon
displays on the LCD.
The fan operates continuously at Med medium speed and the
icon displays on the LCD.
The fan operates continuously High at high speed and the
icon displays on the LCD.
The fan speed varies depending
on the difference between the
Auto temperature set-point and room
temperature. The
icon
displays on the LCD.
8
Operation
HEAT MODE
NOTE: The HEAT mode is only available when the furnace is enabled. The system will cycle the furnace
on and off based on the room temperature and temperature setpoint. There are 4 fan speed selections in this mode. The fan speed selections only apply to the rooftop fan that is part of the Air Conditioner. The fan speed selection does not change the fan speed of the furnace.
The fan operates continuously at
Low low speed and the
icon
displays on the LCD.
The fan operates continuously at Med medium speed and the
icon displays on the LCD.
The fan operates continuously High at high speed and the
icon displays on the LCD.
The fan speed varies depending
on the difference between the
Auto temperature set-point and room
temperature. The
icon
displays on the LCD.
OFF The fan is off. The
icon
displays on the LCD.
FAN MODE
The temperature set-point is not available.
There are 3 fan speed selections in this mode.
The fan operates continuously at
Low low speed and the
icon
displays on the LCD.
The fan operates continuously at Med medium speed and the
icon displays on the LCD.
The fan operates continuously High at high speed and the
icon displays on the LCD.
DRY MODE
Compressor runs continuously when room temperature is higher than set-point.
Compressor cycles ON for 10 minutes and OFF for 6 minutes when room temperature is lower than set-point.
The fan speed runs continuously at low speed.
Set the Temperature
The temperature set-point ranges from
9
Operation
60ºF~86ºF (16ºC~30ºC). 1. Press button to toggle to your
desired mode. 2. Press or button to increase or
decrease the temperature set-point to your comfort level. NOTE: The temperature set-point is not available in FAN mode.
Set the Fan Speed
predefined colors of LED light in the air distribution box. 1. Press LIGHT button on the
thermostat to turn on the mood light. 2. Press LIGHT button to toggle to your
desired mood light. 3. To turn off the mood light, press
LIGHT button repeatedly until the mood light turns off.
Sleep Mode
1. Press button repeatedly to toggle to your desired mode.
2. Press FAN button to select AUTO, HIGH, MEDIUM or LOW fan speed.
NOTE: The fan speed selection is not available in DRY mode.
Mood Light
The thermostat is designed with 7
1. Press SLEEP button on the thermostat to turn on SLEEP mode. The SLEEP icon and the current temperature set-point will be displayed on the LCD.
2. After meeting desired temperature. In Cool Mode: The temperature set-point will increase 2ºF after running for 1 hour and increase 2ºF after running for 2 hours, then the fan speed will be fixed to LOW speed. In Heat mode: The temperature set-point will decrease 2ºF after running for 1 hour and decrease 2ºF after running for 2 hours, then the fan speed will be fixed to LOW speed.
10
Special Features
Auto Fan
LCD Error Code
When the auto fan mode is selected, the fan speed will vary depending on the temperature difference between the temperature set-point and the room temperature.
Temperature Difference >3ºF
>1ºF
<-1ºF
Fan Speed
The fan operates on High level The fan operates on Med level The fan operates on Low level
Compressor Time Delay
A time delay of approximately three minutes occurs any time the compressor is required to begin the cooling cycle.
NOTE: The time delay occurs automatically after a mode is selected or a power event occurs to ensure pressure in the compressor is equalized appropriately, to prevent damage.
Power Interruption
In the event the power to the air conditioner or controller is interrupted, the system will restart automatically with the last status and operational parameter set-points once the power is restored.
The following error code will be displayed on the LCD when the system detects one of the following faults has occurred.
LCD Error Code
E1 Indoor temperature sensor out of order. System will shut down.
E2 Evaporator temperature sensor out of order. System will shut down.
Loss of communication between the E3 thermostat and control box. System
will shut down.
E4 Condenser temperature sensor out of order. System will shut down.
E5 Outdoor temperature sensor out of order. System will shut down.
lo
Insufficient low level of +12V power supply. System will shut down.
11
(OPTIONAL) (CONN TO AIR DISTRIBUTION BOX) USE COPPER CONDUCTORS ONLY.
Wiring Diagram
GRN/YEL
INDOOR MOTOR
C COMPRESSOR
GRN/YEL
R
S
O.L
BLK OUTDOOR
MOTOR GRN/YEL PASSED DIELECTRIC
BRN WHT
IF COM CP
OF
CAPACITOR
WHT BLK YEL RED WHT
BLU RED
BLU
WHT
RED
GRN/YEL
FUSE
RED
RED
LIMMITED SWITCH
HEAT ELEMENT
RED
BLK BLK
HEAT ELEMENT
RED
BLK
RED
6PIN CONN 1 2 3 4 5 6
3PIN CONN 3 2 1
WALL THERMOSTAT
115VAC 60Hz 1
RED YEL BLK
TO UPPER UNIT Elect.Heater Optional*
BK WHT GRN/YEL
LOW
RY2
GAY
COM BK ON
RY7
MED
HIGH BLU WHT
WHT CN6
COIL SENSOR ROOM SENSOR
B
CN3 A 12V
GND CN2
12V R G B
CN5
CN8
CN1
BRN BRN
RED BLK
RGB LED
TO UPPER UNIT
BLU BLK YEL RED WHT GRN/YEL TO FURNACE ANALOG
+12V GND
1 23456
THERM
CONTROL
PASSED DIELECTIC
12
Specifications
DC Input Power Power Consumption Baud Rate Dimension Weight LCD Viewing angle
DC 12V <0.5W 9600bps 3 x 3 x 15/16" (75 x 75 x 22.5mm) 0.06kg 12 o'clock
13
Warranty
FURRION WARRANTS FOR A PERIOD OF 1 YEAR FROM DATE OF RETAIL PURCHASE BY THE ORIGINAL END-USE PURCHASER, THAT THIS PRODUCT, WHEN DELIVERED TO YOU IN NEW CONDITION, IN ORIGINAL PACKAGING, FROM A FURRION AUTHORIZED RESELLER AND USED IN NORMAL CONDITIONS, IS FREE FROM ANY DEFECTS IN MANUFACTURING, MATERIALS, AND WORKMANSHIP. IN CASE OF SUCH DEFECT, FURRION SHALL REPLACE OR REPAIR THE PRODUCT AT NO CHARGE TO YOU. THIS WARRANTY DOES NOT COVER: PRODUCTS WHERE THE ORIGINAL SERIAL NUMBERS HAVE BEEN REMOVED, ALTERED OR CANNOT READILY BE DETERMINED; DAMAGE OR LOSS CAUSED BY ACCIDENT, MISUSE, ABUSE, NEGLECT, PRODUCT MODIFICATION, FAILURE TO FOLLOW INSTRUCTIONS IN INSTRUCTION MANUAL, COMMERCIAL OR INDUSTRIAL USE; DAMAGE OR LOSS CAUSED TO THE DECORATIVE SURFACE OF PRODUCT; TO ANY DATA, SOFTWARE OR INFORMATION; AND NORMAL WEAR AND TEAR. THIS WARRANTY ONLY PROTECTS THE ORIGINAL END-USER ("YOU") AND IS NOT TRANSFERABLE; ANY ATTEMPT TO TRANSFER THIS WARRANTY SHALL MAKE IT IMMEDIATELY VOID. THIS WARRANTY IS ONLY VALID IN THE COUNTRY OF PURCHASE. THIS WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. FURRION SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IF FURRION CANNOT LAWFULLY DISCLAIM IMPLIED WARRANTIES UNDER THIS LIMITED WARRANTY, ALL SUCH WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THIS WARRANTY. No Furrion reseller, agent, or employee is authorized to make any modification, extension, or addition to this warranty.
14
Warranty
FURRION IS NOT RESPONSIBLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DOWNTIME, GOODWILL, DAMAGE TO OR REPLACEMENT OF ANY EQUIPMENT OR PROPERTY, ANY COSTS OF RECOVERING, REPROGRAMMING, OR REPRODUCING ANY PROGRAM OR DATA STORED IN OR USED WITH FURRION PRODUCTS. FURRION'S TOTAL LIABILITY IS LIMITED TO THE REPAIR OR REPLACEMENT OF THIS PRODUCT PURSUANT TO THE TERMS OF THIS WARRANTY. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR EXCLUSIONS OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OR CONDITIONS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY BY STATE OR (WHERE APPLICABLE IN THE COUNTRIES WHERE FURRION HAS NON-US/CANADIAN AUTHORIZED DEALERS) COUNTRY. NO ACTION OR CLAIM TO ENFORCE THIS WARRANTY SHALL BE COMMENCED AFTER THE EXPIRATION OF THE WARRANTY PERIOD. Keep your receipt, delivery slip, or other appropriate payment record to establish the warranty period. Service under this warranty must be obtained by contacting Furrion at warranty@furrion.com Product features or specifications as described or illustrated are subject to change without notice.
15
16
17
18
Furrion Innovation Center & Institute of Technology
52567 Independence Ct., Elkhart, IN 46514, USA Toll free:1-888-354-5792 Email: support@furrion.com
©2007-2018 Furrion Ltd. Furrion® and the Furrion logo are trademarks licensed for use by Furrion Ltd. and registered in the U.S. and other countries. FURRION.COM
IM-FHA00028 V1.0