mailto:care@selectblinds.commailto:customercare@selectblinds.com
Pick the SelectBlinds.com Warranty Thatâs Right For You
Installation Guide for SelectBlinds models including: Woven Wood Shades, Woven, Wood Shades, Shades
Textured Woven Wood Shades | SelectBlinds
File Info : application/pdf, 5 Pages, 1.02MB
DocumentDocumentINSTALLATION GUIDE WOVEN WOOD SHADES LLIIFFTT SSYYSSTTEEMMSS:: CCOONNTTIINNUUOOUUSS CCOORRDD LLOOOOPP || CCOORRDDLLEESSSS LLIIFFTT || MMOOTTOORRIIZZAATTIIOONN ® Simple. Smart. Custom. OUTSIDE MOUNT NOTE: If using your own screws instead of those provided, be sure to pre-drill a small hole with a 5/64" drill bit before the final screws go in to attach brackets. 1. Center and hold the headrail at least two inches above the window. While keeping the shade level, make a small line with your pencil just above each of the pre-drilled holes in the headrail. Set the shade aside. 2. Align the top edge of a bracket along each mark, and use the holes in the back of the bracket to mark where your two screws will go. 3. Align the brackets with the holes, and use a Phillips drill bit to fasten the screws in place. *If you are using wall anchors, pre-drill with a 1/4" bit instead, and tap the wall anchors into the holes with a hammer before drilling in the screws. ® Simple. Smart. Custom. INSTALLATION GUIDE | WOVEN WOOD SHADES UPDATED MAR 2024 2. ATTACHING THE LIFT HANDLE ® Simple. Smart. Custom. INSTALLATION GUIDE | WOVEN WOOD SHADES UPDATED MAR 2024 PROGRAMMING AND USING YOUR REMOTE MOTORIZED WOVEN WOOD SHADES WARNING: DO NOT attempt to raise or lower your motorized shade with your hands. This may cause permanent damage to the motor, and other components in the headrail, which may not be covered under your warranty. Your shade's motor and remote(s) are pre-programmed at the factory, and are ready to use once the shade is installed. Look for the tag with two numbers on the back of each bottom rail. This indicates which channel and remote your shade is programmed to. All you have to do is install the battery in the remote. Open the battery compartment at the bottom of the remote and insert the lithium battery into the round slot, positive side up. Slide the battery cover back onto the remote. LIMIT (L) CONFIRM (C) MOUNTING BATTERY PACK For 1) outside mount and for 2) inside mount with a shallow windowsill, you won't have room behind the headrail to attach the battery pack. You can either 1) attach the battery pack to the wall near the window, or 2) vertically inside the shallow windowsill, below the headrail, and as far back as possible. Note: Be sure your placement of the battery pack allows for uninterrupted operation of your shade and window. 1. To attach battery pack for outside mount: The most important thing to remember is to use a pencil and a level to make sure your mounting clips are aligned when you attach them to the wall. Slide the battery pack into place on the clips when ready. 2. To attach battery pack for shallow inside mount: With a pencil and a level, make sure the mounting clips are aligned vertically when you attach them inside the windowsill, as far back as possible toward the glass, so as not to interfere with the shade's operation. Slide the battery pack into place on the clips when ready. LABEL ® Simple. Smart. Custom. INSTALLATION GUIDE | WOVEN WOOD SHADES UPDATED MAR 2024 PAIRING THE REMOTE WITH A MOTOR NOTE: The factory pairs each of your shades to the remote. The following steps are only necessary if you want to change how the cha nnels are configured, or if you are adding a new shade to a remote already in use. 1. Plug the battery pack into the shade. 2. Set the remote to whichever channel you want to program the shade to. STEP 4 3. Push and hold the button on the battery pack until the shade jogs. 4. With your finger, quickly press and hold the Confirm (C) button on the back of the remote. When the shade jogs (a quick up and down movement), the remote is paired to the channel you've chosen. ADJUSTING UPPER AND LOWER LIMITS NOTE: The upper and lower limits are already set-up at the factory, so the following steps are only necessary if you want to change how these settings are configured. Both limits must be reprogrammed in these instructions. 1. Start with the shade fully raised. For a few seconds, press and hold the Limit button until the shade jogs. Your motor is now in programming mode. 2. Press Down to lower the shade until it's almost to the bottom, then press Stop. From here, repeatedly press Down to lower the shade slowly. 3. When the shade reaches the desired bottom position, flip the remote and use your pen to press the Confirm button. The shade will jog to acknowledge that your lower limit is now set, but the motor is still in programming mode. 4. Press Up to raise the shade until it's almost to the top, then press Stop. From here, repeatedly press Up to raise the shade slowly. 5. When the shade reaches the desired top position, flip the remote and use your pen to press the Confirm button. The shade will jog to acknowledge that your upper limit is now set, and the motor will automatically exit programming mode. CONFIRM (C) CONFIRM (C) LIMIT (L) ® Simple. Smart. Custom. INSTALLATION GUIDE | WOVEN WOOD SHADES UPDATED MAR 2024 Here are some general guidelines on how to do so: Team at 888-257-1840, or email customercare@selectblinds.com. INSTALLATION GUIDE | WOVEN WOOD SHADES UPDATED MAR 2024