Installation Guide for ARMATURA models including: IG_EN v1.5, 20241226, 105X145mm, OmniAC30 All Weather Outdoor Multi Tech Smart Standalone Terminal, OmniAC30, All Weather Outdoor Multi Tech Smart Standalone Terminal, Outdoor Multi Tech Smart Standalone Terminal, Multi Tech Smart Standalone Terminal, Tech Smart Standalone Terminal, Smart Standalone Terminal, Standalone Terminal
%PDF-1.7 %âãÏÓ 4 0 obj /Type /Page /Parent 2 0 R /Contents 10 0 R /MediaBox [-0.0000 -0.0000 297.6378 411.0236] /TrimBox [0.0000 0.0000 297.6378 411.0236] /CropBox [-0.0000 -0.0000 297.6378 411.0236] /Resources /ProcSet [/PDF /ImageB /Text] /XObject /Im28 28 0 R /Im30 30 0 R >> /Shading /Sh19 19 0 R >> /Font /HeBo 31 0 R /Helv 38 0 R >> /ExtGState /GS11 11 0 R /GS16 16 0 R >> /ColorSpace ...
OmniAC30 Installation Guide Version: 1.5 How to Install the Device? Installation Environment Please refer to the following recommendations for installation. window 6.5ft 10ft KEEP DISTANCE AVOID GLASS REFRACTION Device Installation AVOID DIRECT SUNLIGHT AND EXPOSURE KEEP EFFECTIVE DISTANCE 0.3-2m With Backplate : 1. Attach the mounting template sticker to the wall, and drill holes according to the mounting paper. 2. Fix the Backplate on the wall using wall mounting screws. 3. Attach the device to the Backplate. 4. Fasten the device to the Backplate with a security screw. 1 2 53.15" / 1.35m 3 4 1 With Back Cover: 1. Attach the mounting template sticker to the wall, and drill holes according to the mounting paper. 2. Fix the Back Cover on the wall using wall mounting screws. 3. Attach the device to the Back Cover. 4. Fasten the device to the Back Cover with a security screw. 1 2 49.21" / 1.25m 3 4 Note: Features and parameters with mark are not available in all devices. 2 Wiring Diagram Power Connection Recommended AC Adapter 1) 12V ± 10%, at least 3A. 2) To share the power with other devices, use an AC Adapter with higher 12V current ratings. Ethernet Connection Connect the device and computer software over an Ethernet cable. As shown in the example below: PC Default IP address: 192.168.1.201 Subnet mask: 255.255.255.0 IP address: 192.168.1.130 Subnet mask: 255.255.255.0 Click on [COMM.] > [Ethernet] > [IP Address] , input the IP address and click on [OK]. Note: In LAN, the IP addresses of the server (PC) and the device must be in the same network segment when connecting to the software. 3 Wiegand Reader and RS485 Connection 485B 485A GND 12V-OUT WD1-OUT WD0-OUT IWD1 IWD0 GND 12V-OUT 485 Reader 485485+ GND +12V WD1 WD0 GND +12V Wiegand Reader Access Controller GND WD1 WD0 Door Sensor, Exit Button, Auxiliary Connection AUX SEN GND BUT NO COM NC ALARMALARM+ Smoke Detector NO COM Detector Power Door Sensor Alarm Alarm Power ExitButton 4 Lock Relay Connection The system supports Normally Opened Lock and Normally Closed Lock. The NO LOCK (normally unlocked when power-on) is connected with 'NO' and 'COM' terminals, and the NC LOCK (normally locked when power-on) is connected with 'NC' and 'COM' terminals. Take NC Lock as an example below: 1)Device not sharing power with the lock Lock AUX SEN GND BUT NO COM NC ALARMALARM+ +12V GND DC 12V FR107 AC Adapter DC12-3A 12V 2)Device sharing power with the lock AUX SEN GND BUT NO COM NC ALARMALARM+ +12V GND 5 Lock FR107 DC 12V AC Adapter DC12-3A 12V Printer Connection 12V-OUT GND GND RS232-RXD RS232-TXD RS232 Cable Printer 6 Copyright © 2025 ARMATURA LLC. All rights reserved.Corel PDF Engine Version 22.1.1.523 CorelDRAW 2020