Home - NEXX Helmets
Instruction Manual for NEXX models including: X.WST3, X.WST3 Plain Full Face Helmet, Plain Full Face Helmet, Full Face Helmet, Face Helmet, Helmet
Manuals – Nexx UK
Manuals - NEXX Helmets
File Info : application/pdf, 38 Pages, 1.86MB
DocumentDocumentEN CN X.WST3 At NEXX, we do not just engineer helmets, we tech emotions. We believe in the heat of passion - parts of life getting new blood. HELMETS FOR LIFE is our motto, beyond the protection, past excellence, that any motorcyclist regardless of age or style lives the moment they wear NEXX. CONTENT 04 INSTRUCTION MANUAL 05 PARTS DESCRIPTION 06 VENTILATIONS 09 HOW TO CLEAN THE VISOR 10 HOW TO REMOVE THE VISOR 11 HOW TO PLACE THE VISOR 12 HOW TO USE THE INNER SUN VISOR 13 HOW TO REMOVE DE INNER SUN VISOR 14 HOW TO PLACE THE INNER SUN VISOR 15 PINLOCK 16 ERGO-PADDING * 17 HOW TO PLACE ACTION CAMERA SIDE SUPPORT * 18 LINING SPECIFICATIONS 19 FRS - FAST RELEASE SYSTEM 20 FRS - FAST RELEASE SYSTEM 23 HOW TO REMOVE THE INNER LINING 24 HOW TO PLACE THE INNER LINING 28 HOW TO CHANGE DUST FILTER FOR WINTER FILTER 29 ACCESSORIES 30 SIZE CHART 32 X.COM 3 * 35 HOMOLOGATION TAG 36 HELMET CARE * Not included / 3 EN Please read this manual very carefully before wearing your helmet and keep it in a safe place. For a correct use and for your safety, please pay attention to following instructions. The main function of the helmet is to protect your head in case of impact. This helmet is made to absorb some of the energy of a blow by partial destruction of its component parts and, even though damage may not be apparent, any helmet which has suffered an impact in an accident or received a similarly severe blow or other abuse should be replaced. To maintain the full efficiency of this helmet, there must be no alteration to the structure of the helmet or it´s component parts. CN 4 PARTS DESCRIPTION 3 6 2 7 8 9 10 1 4 5 11 12 1 - Shell / 2 - Visor / Shield / / 3 - Top Air Intake ventilation / 4 - Chin Air Intake Ventilation / 5 - Chin Wings Deflector / 6 - Frontal Air Intake Ventilation / 7 - Sunvisor Lever / 8- Spoiler / 9 - Spoiler Extensor / 10 - Visor Mechanism / / 11- FRS - Fast Release System Lever / 12- X.COM 3 cover / X-COM 3 5 VENTILATIONS TOP INTAKE VENTILATIONS OPEN AIRFLOW CIRCUIT TOP INTAKE VENTILATIONS CLOSE 6 VENTILATIONS FRONTAL INTAKE VENTILATIONS CLOSE FRONTAL INTAKE VENTILATIONS OPEN AIRFLOW CIRCUIT LATERAL INTAKE VENTILATIONS CLOSE LATERAL INTAKE VENTILATIONS OPEN 7 VENTILATIONS AIRFLOW CIRCUIT CHIN INTAKE VENTILATIONS OPEN CHIN INTAKE VENTILATIONS CLOSE CHIN WINGS DEFLECTOR: HELMET STABILIZER 8 HOW TO CLEAN THE VISOR EN To clean the visor without affecting its characteristics should be used only soapy water (preferably distilled) and a soft cloth. If the helmet is deeply dirty (ex.Insect remains) can add a little liquid from the dish to water. Remove the visor from the helmet before carrying a deeper cleaning. Never use objects to clean the helmet that may damage/scratch the visor. Always store the helmet in a dry place and protected from light, preferably in the bag provided by NEXX HELMETS. CN / NEXX HELMETS 9 HOW TO REMOVE THE VISOR 1 OPEN THE VISOR ALL THE WAY UP 2 PUSH THE BUTTON - BOTH SIDES 3 REMOVE THE VISOR 10 HOW TO PLACE THE VISOR 1 ALIGN THE VISOR PINS WITH THE MECHANISM HOLES 2 PRESS TO LOCK 11 HOW TO USE THE INNER SUN VISOR 1 CLOSE 2 FULL CLOSE POSITION 3 OPEN 12 4 FULL OPEN POSITION HOW TO REMOVE DE INNER SUN VISOR 1 OPEN THE SUNVISOR 2 PULL FROM BOTH SIDES 3 PULL FROM BOTH SIDES 13 4 REMOVE THE VISOR HOW TO PLACE THE INNER SUN VISOR 1 INSERT BOTH SIDES 2 PULL UP 14 3 READY TO USE PINLOCK * 4 4- Remove the film 15 ERGO PADDING * * Not included / 16 CAMERA SIDE SUPPORT 1 2 Use Tork screwdriver T10 or Hex screwdriver H2.5 3 4 5 6 17 LINING SPECIFICATIONS The lining of the helmet has the following characteristics: EN - Removable (only some models), - Anti-allergy - Anti-sweat This lining can be removed and washable, as shown in the picture (only some models). If for some reason this lining is damage it can be easily replaced (only some models). CN - - - 18 REMOVABLE LINER PARTS Ear Pad (R) Deflector Ear Pad (L) Center Linner 19 FRS - FAST RELEASE SYSTEM REMOVE THE EARPADS FOR CLEANING PURPOSES 1 PULL THE LEVER 2 SLIDE THE RED BUTTON 20 3 PULL THE LINNER EARPAD (REPEAT THE PROCESS THE OTHER SIDE) ( FRS - FAST RELEASE SYSTEM REMOVE THE EARPADS IN CASE OF EMERGENCY 1 PULL THE LEVER 2 SLIDE THE RED BUTTON 21 3 PULL THE LINNER EARPAD (REPEAT THE PROCESS THE OTHER SIDE) ( FRS - FAST RELEASE SYSTEM REMOVE THE EARPADS IN CASE OF EMERGENCY 4 PULL THE EMERGENCY STRAP (BOTH SIDES) 5 REMOVE THE EARPAD (BOTH SIDES) 6 REMOVE THE HELMET SAFELY 22 HOW TO REMOVE THE INNER LINING 1 PULL THE EARPADS BOTH SIDES USING FRS SYSTEM (SEE PREVIOUS PAGE) 2 PULL THE BACK SIDE OF THE LINNER 3 RELEASE THE SPRINGS 23 4 PULL THE FRONTAL PART OF THE LINNER HOW TO PLACE THE INNER LINING 1 INSERT THE FRONT OF THE LINNER 2 TIGHTEN THE SPRINGS 3 INSERT ON THE BACK 24 4 MAKE THE STRAP PASS THROUGH THE EARPADS HOW TO PLACE THE INNER LINING 5 SLIDE THE RED BUTTON TO LOOSE THE EARPADS (SEE FRS PAG.31) (31"" 6 INSERT ( 37) 7 INSERT ( 37) 25 8 PRESS AND SLIDE FRS BUTTON UNTIL CLOSE POSITION HOW TO PLACE THE INNER LINING 9 PRESS THE PIN 10 PRESS THE PIN 11 PRESS THE PIN 12 MAKE SURE THE BUTTON IS SECURELY LOCKED AND THE EARPADS SECURELY ATTACHED 26 HOW TO PLACE THE INNER LINING INSERT EARPADS WITH FRS 27 HOW TO CHANGE DUST FILTER FOR WINTER FILTER 1 REMOVE THE CHIN FILTER HOLDER AND THE DUST FILTER 2 INSERT THE WINTER FILTER AND THE CHIN FILTER HOLDER 28 ACCESSORIES HELMET BAG ACCESSORIES BAG CAMERA SIDE SUPPORT DEFLECTOR EXTRA VISOR * PINLOCK * WINTER FILTER SMALL SCREWS X2 x2 *Available in some models 29 SIZE CHART SHELL SIZE HELMET SIZE HEAD SIZE CM IN XXS 51/52 20,1/20,5 XS 53/54 20,9/21,3 S 55/56 21,7/22 M 57/58 22,4/22,8 L 59/60 23,2/23,6 XL 61/62 XXL 63/64 XXXL 65/66 24/24,4 24,8/25,2 25,6/26 EN CN 30 The size selection of the helmet is crucial to ensure the safety of the user. Never should use a helmet that is EN too small or too large in relation to the size of the head. To purchase a helmet is important that you try it: make sure the helmet fits perfectly to the head, there should be no gap between the helmet and the head; make some movements of rotation (left and right ) with the helmet on the head(closed) this should not shake; it´s important that the helmet is comfortable and involving the entire head. CN 31 X.COM 3 * The X.WED 3 model is by Default Equipped to Accommodate the NEXX Helmets X-COM 3 Communications System. X.WED3 Mesh *PRO version only PRO 1 2 3 4 * Not included / 32 X.COM 3 * RIGHT SIDE * Not included / 33 Mesh *PRO version only PRO X.COM 3 * ANTENNA * Not included / 34 HOMOLOGATION TAG HOMOLOGATION TAG INSERTED HERE 35 HELMET CARE SOIN À PRENDRE PFLEGE EN - Light colors with matte finish require extra care as they are naturally more exposed to dust, fumes, compounds or other types of impurities. THIS IS NOT COVERED UNDER WARRANTY! Neon colors will fade when subjected to prolonged UV rays exposure. THIS IS NOT COVERED UNDER WARRANTY! We are not liable for any damage, loss or detriment resulting from faulty assembly of any accessory. - Do not expose the helmet to any type of liquid solvent; - The helmet should be handled with care. Leaving it drops can damage the painting as well as reduce their characteristics of protection. THIS NOT COVERED UNDER WARRANTY! - Keep the helmet in a safe place (not hang on the mirror of motorcycle or other support than can damage the lining). Do not carry your helmet on the biker or in the arm while driving. - Always use the helmet in the proper position, using the buckle to adjust to the head; - In order to maintain trouble free operation of the visor, it is advisable to periodically lubricate the mechanisms and rubber parts around the visor with silicone oil. The application may be made with a brush or with the help of a cotton swab. Apply sparingly and remove the excess with a dry clean cloth. This proper care will maintain the softness of the rubber seal and will dramatically increase the durability of the visor fixing mechanism. - Clean and lubricate mechanisms after use in extreme off road dust and dirt conditions. CN - - - - - - - 36 This hight quality helmet is made with the most advanced European technology. The helmets are EN technologically advanced for the motorcycle rider´s protections, which are made for motorcycle riding only. This helmet specifications is subject to change without notice. CN 37 Nexxpro Fábrica de Capacetes S. A. Zona insdustrial de Amoreira da Gândara, lote nº11 3780-024 Amoreira da Gândara, Anadia - PORTUGAL nexx@nexxpro.com www.nexx-helmets.com MADE IN MARÇO 2023/R01