Tour guide system, Wireless tour guide system, Pager system, Wireless calling system, Pager – WirelessLinkx
Instruction Manual for WirelessLink models including: 2A7KF-813T, 2A7KF813T, 813T, 813T Wireless Tour Transmitter, Wireless Tour Transmitter, Tour Transmitter, Transmitter
Shanghai Biancheng Electronic Technology Co., Ltd. 813T Wireless Tour Guide System 2A7KF-813T 2A7KF813T 813t
File Info : application/pdf, 5 Pages, 253.55KB
DocumentDocument813T & 813R Operation Manual 813T Transmitter : Power On/Off: 3 options: LOCK/ON/OFF; After switching on the device, the channels and battery bar will be shown on the display. Mute Button: Press M, and display will show MUTE. Now the transmitter is muted. Press the M again, and it will be in normal working state. Charging LED Light: red light in charging; blue light: fully charged. Channel Change: Press LEFT or RIGHT button below CHANNEL to change the transmitter channel. When the switch button is on LOCK, the channel can't be changed. The button below "M"has no function. Model: 813R Receiver Change the Channel: Press the or button to change the channel after the device is switched on. When the switch button is on LOCK, the channel can't be changed. When transmitter and receivers are in the same channel, receivers can hear the transmitter. Change the Volume: Press + or - button to change the volume. Make sure the headphone is plugged into the 3.5mm jack deep enough, so the receiver can hear the transmitter. Note: These products are one way wireless communication system. Widely used in the simultaneous interpretation, tour guiding, teaching, training, conferences, etc. One transmitter can talk in one group to numerous receivers. The working frequency is mainly UHF 794-806MHz in Asia, UHF 863-865MHz in Europe, and UHF 902-928MHz in North America. Only manufacturer can change the frequency. The devices use rechargeable batteries. 813T transmitter can work 8 hours continuously after full charge and 813R receiver can work 15 hours continuously after full charge. Type-C cables can be used to charge the devices. Wrong and violent plugging will damage the charging port in the device. It will take 3 hours for full charge. When the devices are being charged, the light will turn red. When they are fully charged, the light will turn blue. Manufacturer: Shanghai Biancheng Electronic Technology Co., Ltd. Address: Building #C, 180 South Changjiang Road, Shanghai, China TEL: +86 15921788065 Website: www.wirelesslinkx.com Specifications Transmitter Parameters Receiver Parameters Frequency: 902-928MHz Frequency: 902-928MHz Number of channels: 26 Number of channels: 26 Channel interval: 1MHz Channel interval: 1MHz Battery: lithium polymer battery Receiving sensitivity: -100dbm Working current: 125mA Working current: 60mA Charging current: 350mA Charging current: 350mA Output interface: 3.5mm Input interface: 3.5mm Battery: 3.7V / 1000mAH Battery: 3.7V / 1000mAH Size: 86.5*48*18mm Size: 86.5*48*18mm Weight: 55g Weight: 55g Distortion: 1% Distortion: 1% Frequency response range: 20Hz - 10KHz Frequency response range: 20Hz - 10KHz Working distance: 150 meters Working distance: 150 meters SNR(Signal to Noise Ratio): 100dB SNR(Signal to Noise Ratio): 100dB Battery life: 8 hours Battery life: 15 hours Federal Communications Commission (FCC) Statement. This device complies with part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide Reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one ormore of the following measures: ·Reorient or relocate the receiving antenna. ·Increase the separation between the equipment and receiver. ·Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ·Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications made to this device not expressly approved by Shanghai Biancheng Electronic Technology Co., Ltd. may void the FCC authorization to operate this device.Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment. RF exposure statement: This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The device is installed and operated without restriction.