QSFPTEK - Trusted Transceivers, Optical Network Solution Partner
User Guide for QSFPTEK models including: S7300-48TE4X2Q Multi Gigabit Ethernet L3 Switch, S7300-48TE4X2Q, Multi Gigabit Ethernet L3 Switch, Gigabit Ethernet L3 Switch, Ethernet L3 Switch
S7300-48TE4X2Q, 48-Port Multi-Gigabit Ethernet L3 Switch,48x 100M/1000M/2.5GBASE-T, with 4x 1G/10G SFP and 2x 40G QSFP Uplink Ports
File Info : application/pdf, 11 Pages, 1.03MB
DocumentDocumentS7300-48TE4X2Q Quick Start Guide 48-Port Multi-Gigabit Ethernet L3 Switch 48x 100M/1000M/2.5GBASE-T, with 4x 1G/10G SFP+ and 2x 40G QSFP+ Uplink, Support BGP V1.0 www.qsfptek.com v1.0 1 / 11 Introduction The QSFPTEK S7300-48TE4X2Q multi-gigabit L3 switch has 48x 100M/1000M/2.5GBASE-T RJ45, 4x 10G and 2x 40G uplink ports. It delivers 600 Gbps switching capacity and 360 Mpps forwarding rate. It supports mature IPv6 features, comprehensive security and reliability features, simple to deploy and manage. It can be used as an ideal and cost-effective access or aggregation layer switch for campus networks. We appreciate your decision to select S7300-48TE4X2Q. This manual is intended to help you become acquainted with the switch desi gn and provide instructions for implementing the switches into your network. Accessories www.qsfptek.com v1.0 2 / 11 Hardware Overview Front Panel Ports RJ45 ETH Ports 1G/10G SFP+ Port 100M/1000M/2.5G-T TX Port 40G QSFP+ Port CON Port ETH Port Description SFP+ ports, with LINK/ACT indicators RJ45 ports, with LINK/ACT indicators SFP+ A baud rate of 9600bps, RJ45 port An RJ-45 Ethernet management port QSFP+ CON Front Panel LEDs RJ45 SYS LEDS RJ45 (Port 1-48) SFP+ (Port TE1-TE4) QSFP+ (Breakout) SYS LED PWR LED SFP+ Breakout Status Description Green On 2.5G port link. Blinking 2.5G packets receiving or transmitting. Green On 10G port link. Blinking 10G packets receiving or transmitting. Green On 10/40G port link. Blinking 10/40G packets receiving or transmitting. / / If the SYS indicator flickers, the system works normally. / / If the PWR indicator is always on, the device is powered on. PWR www.qsfptek.com v1.0 3 / 11 Back Panel 4 Bulit-in Fans Grounding Column AC POWER1 Installation Requirements Tools Preparation Screwdriver Static-proof wristband Bolt Ethernet cable Other Ethernet terminal devices Control terminal AC POWER2 Safety Principles Keep dustless and clean during or after the installation. Put the cover at the safe place. Put tools at the right place where they are not easily falling down. Put on relatively tight clothes, and fasten the tie or scarf well and roll up the sleeve, avoiding stumbling the machine box. Put on the protective glasses if the environment may cause damage to your eyes. Avoid incorrect operations that may cause damage to human or devices. Site Environment Make sure that the workshop is well-ventilated, the heat of electrical devices is well-discharged Avoid to damage devices by following the electrostatic discharge prevention procedure. S5300-48M6X Hardware Installation Manual Put the machine box at the place where cool air can blow off the heat inside the machine box. Make sure the machine box is sealed. www.qsfptek.com v1.0 4 / 11 Mounting the Switch Connecting the Power 1. Plug the AC power cord to the switch power port on the back rear. 2. Connect the other end of the power cord to a AC power source equipment. Connecting the RJ45 Port www.qsfptek.com v1.0 5 / 11 1. Connect one end of the Ethernet cable to the RJ45 port on networking equipment, such as PC, printer, server, storage, etc. 2. Connect the other end of the Ethernet cable to the switch RJ45 port. Connecting the SFP+ Port 1. Insert the SFP+ module into the SFP+ port. 2. Plug a fiber patch cable to the SFP+ transceiver. 3. Connect the other end of the fiber to the device that you want to realize data communication. www.qsfptek.com v1.0 6 / 11 Connecting the QSFP+ Port 4. Insert the QSFP+ module into the QSFP+ port. 5. Plug a fiber patch cable to the QSFP+ transceiver. 6. Connect the other end of the fiber to the device that you want to realize data communication. Connecting the Management Ports Connecting the Console Port 1. Prepare an console cable. 2. Insert the RJ45 connector of the console cable into the console port on the switch. 3. Connect the D89 female connector on the other end of the console cable to the serial port on the computer host. www.qsfptek.com v1.0 7 / 11 Configuring the Switch Configuring the Switch Using the Web-based Interface Step 1: Connect your computer to the switch using an Ethernet cable and open a web browser. Step 2: Set the IP address of the computer to 192.168.0.x (where "x" is any number from 2 to 254) and the subnet mask to 255.255.255.0. Step 3: Open a web browser and type http://192.168.0.1 in the address bar. Enter the default username and password (admin/admin) .Step 4: Click sign-in to access the web-based configuration page. www.qsfptek.com v1.0 8 / 11 Configuring the Switch Using the Console Port Step 1: Use the console cable to direct connect the switch console port to your computer. Step 2: Launch the terminal simulation software such as Hyper Terminal on the computer. Step 3: Configure the parameters of the terminal emulation software as follows: 9600 bits per second, 8 data bits, no parity, 1 stop bit, and no flow control. Step 4: Enter the default username and password (admin/admin). www.qsfptek.com v1.0 9 / 11 Troubleshooting Hardware Fault Analysis Power and cooling systems--power and fan Port, cable and connection--ports on the front panel of the switch and the cables connecting these ports Faults Relative with Power and Cooling System Do the following checkups to help remove the fault: 1. When the power on-off is at the "ON" location, check whether the fan works normally. If the fan does not work well, check the fan. 2. If the switch is too hot, check whether the air outlet and air inlet are clean and then do relative operations in section 2.3 "Requirements for Common Locations". 3. If the switch cannot be started and the PWR indicator is off, check the power. Faults Relative with Port, Cable and Connection Do the following checkups to help remove the fault: If the port of the switch cannot be linked, check whether the cable is correctly connected and whether the peer connection is normal. If the power on-off is at the "ON" location, check the power source and the power cable. If the CLI port does not work after the system is started up, check whether the CLI port is set to a baud rate of 9600 bps, eight data bits, no sum check bit, one stop bit and no traffic control. www.qsfptek.com v1.0 10 / 11 Support and Other Resources Contact us https://www.qsfptek.com/company/contact-us.html Email sales@qsfptek.com Customer Success https://www.qsfptek.com/resources/customer-success-stories Product Warranty S7300 series switches are backed by a 5-year limited warranty supported by QSFPTEK. And you are eligible to apply for a return or e -xchange of your items within 14 days of receiving them. For more details about applying qualifications, please live chat or email sales@qsfptek.com for support. 5 Years Warranty 30-day Return Window www.qsfptek.com v1.0 11 / 11