User Manual for FOAMit models including: FI-20N, FI-20NK, FI-20NV, FI-20N-ST, FI-20NK-ST, FI-20NV-ST, 20 Gallon Air Operated Portable Foam Equipment, 20 Gallon Air Operated, Portable Foam Equipment, Foam Equipment
USER MANUAL MODEL NUMBER: FI-20N FI-20NK FI-20NV FI-20N-ST FI-20NK-ST FI-20NV-ST AND RELATED UNITS 20 Gallon Air Operated Portable Foam Equipment English (Original Instructions)
File Info : application/pdf, 6 Pages, 670.98KB
DocumentDocumentUSER MANUAL MODEL NUMBER: FI-20N FI-20NK FI-20NV FI-20N-ST FI-20NK-ST FI-20NV-ST AND RELATED UNITS 20 Gallon Air Operated Portable Foam Equipment English (Original Instructions) User Manual: Rotomolded Portable Foam Units | English READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT WARNING Read this manual completely and understand the machine before operating or servicing it. · Always wear protective clothing, gloves, and eyewear while operating or servicing unit. · Avoid contact of cleaning agent with skin and eyes. If contact occurs, see SDS sheet for further first aid measures. · Read chemical's Safety Data Sheet (SDS) before using this unit. · Never point the discharge wand at anyone. · Incoming air pressure cannot exceed 100 psi (7 bar). · After each use, relieve all remaining pressure in the system by unplugging the air line from the unit and opening the discharge ball valve to prevent accidental discharge. · After relieving the pressure from the unit, store the unit with the ball valve in the closed position. · Be sure to flush the unit with fresh water for 5 minutes when switching from an alkaline to an acid or an acid to an alkaline. · Do not exceed a fluid temperature of 100°F (37°C). · Only use clean and dry air. Air must be filtered and free of moisture or pump life will be diminished. If needed, install an air dryer before unit. · Do not use air lubricator before the unit. Specifications: Hose ............ 30 feet reinforced hose, 3/4 inch inside diameter (9 meters reinforced hose, 19 mm inside diameter) Foam Output.................................... 20 to 45 gallons/minute (75 to 170 liters/minute) Foam Distances ............................... 25 to 30 feet (7 to 9 meters) Liquid Temperature ........................ 40°F to 100°F (4.4°C to 37°C) Noise Level...................................... Average 79 dB(A) Discharge Wand Vibration Level ..... Maximum 2.5 m/s² Dimensions: Length ....................................... 22 in (559 mm) approximately Width ........................................ 17 in (432 mm) approximately Height ....................................... 48 in (1219 mm) approximately Weight, including discharge hose and wand: (Empty) ................................ 52 lbs (24 kg) approximately (Full) ..................................... 223 lbs (101 kg) approximately Requirements: Compressed Air Pressure Requirements: Air regulator (R25) factory set at 50 psi (3.4 bar). Operating range is 40 to 80 psi (3 to 5 bar) with 5 to 10 CFM (141.64 to 283.30 l/min) Chemical requirements: follow all instructions from chemical manufacturer. Air Operated Double Diaphragm Pump Models Offered: P56: Polypropylene body with Santoprene diaphragm P56V: Polypropylene body with Viton diaphragm P56K: Polypropylene body with Kalrez diaphragm Acceptable Products: Alkaline cleaners, Caustic cleaners, Sanitizers, and Acids * D-Limonene may only be used with Kalrez pump * Chlorine may only be used with Viton or Kalrez pump DO NOT USE: All hydrocarbons PROTECT THE ENVIRONMENT Please dispose of packaging materials, old machine components, and hazardous fluids in an environmentally safe way according to local waste disposal regulations. Always remember to recycle. *Specifications and parts are subject to change without notice. Model No.: FI-20N, FI-20NK, FI-20NV, FI-20N-ST, FI-20NK-ST, FI-20NV-ST Page 2 of 6 | 20221205 User Manual: Rotomolded Portable Foam Units | English READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT Operation Instructions: 1. Follow all instructions from chemical manufacturer. Fill the tank with water and the advised percentage of chemical concentrate. 2. With ball valve (HV60) in the closed position, plug an air line into the air fitting (AP25). 3. Slowly open the ball valve (HV60) completely. 4. Adjust the needle valve (NV14Y) to desired wetness or dryness of foam following the steps below: a. Close needle valve completely in clockwise direction. b. Open needle valve in counter-clockwise direction 3 complete turns. c. Continue to open valve in ¼ turn increments allowing 30 seconds between adjustments until proper consistency of foam is achieved. After Use Instructions: 1. Flush the unit with fresh water for 5 minutes. 2. Disconnect the air line from the air fitting (AP25) and relieve any remaining pressure in the system by opening the discharge ball valve (HV60). 3. Close the ball valve (HV60) after all pressure has been relieved from the system. Maintenance Instructions: To keep your portable tank foamer operating properly, periodically perform the following maintenance procedures: · Check the air pump (P56/P56K/P56V) for wear and leaks. · Inspect hoses for leaks or excessive wear. Make sure all hose clamps are in good condition and properly secured. · Replace filter (AFR25) in regulator (R25) as needed. · Check the suction tube and screen for debris and clean as needed. · Drain compressor tank on a regular basis to ensure proper operation of pump. Troubleshooting Instructions: · Check to ensure the discharge hose is uncoiled properly, and that there are no kinks that could obstruct fluid flow. · Check air regulator bowl (ABR25) for debris such as water, oil, or rust particles. Clean by unthreading the air regulator bowl from the air regulator (R25). · If needle valve (NV14Y) valve is open too far, the pump (P56/P56K/P56V) will cycle improperly due to lack of air pressure. If this occurs, reset needle valve as described in Operation Instruction #4. · Make sure proper foaming chemical and concentration is being used. · If air passes through the pump (P56/P56K/P56V) without cycling, the pump needs to be replaced. · If foam solution backs up into air regulator bowl (ABR25), the check valve (CV38) needs to be replaced. · If foam comes out wet, no matter where the needle valve (NV14Y) is positioned, the check valve (CV38) may need to be replaced. · Check for proper air pressure on air gauge (AG100). Air regulator (R25) is factory set at 50 psi (3.4 bar). Operating range is 40 to 80 psi (3 to 5 bar) with 5 to 10 CFM (141.64 to 283.30 l/min) · If the unit foams at a reduced pressure: o Check the air compressor supplying the unit. If the pressure is less than 40 psi, turn the foam unit off until the compressor can catch up. o If the air supply is 50 psi (3.4 bar) or above, check the AG100, which should read near 50 psi (3.4 bar). If the AG100 is more or less than 50 psi (3.4 bar), adjust the pressure by turning the knob on the top of the air regulator (R25). o If both of the above are okay, the stainless steel mixing mesh (SS-MESH) could be plugged. Remove and clean it by following the instructions below: 1. Be sure the foam unit is not plugged into an air supply and be sure to relieve all stored pressure in the unit by having the ball valve (HV60) in the open position. 2. Remove the stainless adaptor (HBSS1234) from the tee fitting (SST12HB38). 3. Remove the screen and the mixing mesh from inside the tee fitting (SST12HB38). 4. Clean any particles from the mixing mesh and the screen. 5. Replace the mixing mesh and then the screen into the back of the tee and screw the stainless adaptor back into the tee. It is recommended to use a pipe thread sealant when reinstalling the stainless adaptor back into the tee fitting (SST12HB38). If the mixing mesh has a lot of foreign particles in it, make sure the strainer (STR38-IL) is still in place. · Check for plugged strainer (STR38-IL). Replace strainer if necessary. Strainer must be used. Model No.: FI-20N, FI-20NK, FI-20NV, FI-20N-ST, FI-20NK-ST, FI-20NV-ST Page 3 of 6 | 20221205 User Manual: Rotomolded Portable Foam Units | English READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT TANK ASSEMBLY ITEM NUMBER: TANK-20N-A DFP7 (see parts list for color opons) TANK-20N COT FWAX15 W15 FWAX15 SSP12 AS1-VS SSAXLE15 DP-A PVCV34FM HOSE AND WAND ASSEMBLY ITEM NUMBER: SSWA38-HA30 ZERO TIP FOAM WAND ASSEMBLY ITEM NUMBER: SSWA38 HBSS1234 HV60 HHSB1238 W387 30 ft (9 m) HOSE ASSEMBLY ITEM NUMBER: H34-30 FAN TIP FOAM WAND ASSEMBLY ITEM NUMBER: PWA34-ST HBSS1234 HV60 SN1212 PW10 ST80200 H34B-F (Available per ft.) HBSS1234 SSC34 ANTI-KINK SPRING ASSEMBLY ITEM NUMBER: AKSS34 AKSS34 Model No.: FI-20N, FI-20NK, FI-20NV, FI-20N-ST, FI-20NK-ST, FI-20NV-ST Page 4 of 6 | 20221205 User Manual: Rotomolded Portable Foam Units | English READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT PLATE ASSEMBLY ITEM NUMBER (Santoprene pump): PA-PF34 ITEM NUMBER (Kalrez pump): PA-PF34K ITEM NUMBER (Viton pump): PA-PF34V Plate - Inside View P56, P56K, or P56V P56-BRKT P56-BRKT-SCREW HBSSEL1438 NV14Y R25 AG100 HBSSEL1438 HBSSEL1814 HBSS1438 SSC38 SST12HB38 EC14-2 SSC38 CV38 BPS-58SO BPS-58SO STR38-IL HHPB3414 SSC38 HBSSEL1438 Plate - Back View NV14Y SSA14 AP25 FWP12 HBSS1234 PVCV34FM OPTIONAL COMPONENTS WATER SEPARATOR 30 ft (9 m) AIR HOSE ASSEMBLY ITEM NUMBER: WS-20CFM ITEM NUMBER: AH30 Model No.: FI-20N, FI-20NK, FI-20NV, FI-20N-ST, FI-20NK-ST, FI-20NV-ST Page 5 of 6 | 20221205 User Manual: Rotomolded Portable Foam Units | English READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT ITEM NUMBER DESCRIPTION AG100 1.5in DRY MODEL 20 DUAL SCALE GAUGE AKSS34 SS ANTI-KINK SPRING FOR 3/4 INCH HOSE WITH PIN AP25 PLUG 1/4 NPTM AIR FITTING - BRASS AS1-VS 1/4-20 X 1/2 PHIL TRUSS MACH SCREW 19-8 W/516 ORANGE VIBRASEAL PATCH B8X58 8 X 5/8 inch STAINLESS STEEL SHEET METAL SCREW BPS-58SO Back Panel Screw - 5/8 inch with Stand Off BPS-SSR 1/4 INCH PUSHNUT BOLT RETAINER STAINLESS STEEL COT 1/8 X 1 COTTER PIN 18-8 S/S CV38 PVC CHECK VALVE 3/8 BARBS - SS SPRING DFP7 7 INCH HINGED CAP ASSEMBLY - INCLUDES BLACK CAP, LID FLANGE AND HINGE PIN DFP7-C 7 INCH FILL CAP POLYPRO BLACK DFP7-F 7 INCH TANK LID FLANGE POLYPRO DFP7-PIN HINGE PIN FOR 7 INCH FILL CAP AND FLANGE DFP7-C-BL 7 INCH FILL CAP POLYPRO BLUE PANTONE DFP7-C-GN 7 INCH FILL CAP POLYPRO GREEN PANTONE DFP7-C-RD 7 INCH FILL CAP POLYPRO RED PANTONE DFP7-C-YL 7 INCH FILL CAP POLYPRO YELLOW PANTONE DP-A DRAIN PLUG ASSEMBLY FOR TANK-10N TANK-20N DP FRONT DRAIN PLUG FOR PORTABLE UNIT POLYPRO DP-G FKM SQUARE CUT DRAIN PLUG GASKET DP-INSERT 304 STAINLESS DRAIN PLUG INSERT EC14-2 OETIKER CLAMP 13.8 EC75 OETIKER CLAMP-12/04/07 F34SS-L SS CRIPM FERRULE 1.90inches X 1.5 inches LONG F38SS STAINLESS 3/8 INCH FERRULE FACI14 FEMALE COUPLER - 1/4in NPTF FWAX15 FLAT AXLE WASHER FWP12 7/8 ID X 1.5 OD X 0.05 THK SSFW FWP14 C-816 1/2in SS WASHER H14B-F 1/4 INCH BLUE HOSE-HYBRID TPE-Available per ft. H34B-F 3/4 INCH BLUE HOSE-HYBRID TPE-Available per ft. H38B-F 3/8 INCH BLUE HOSE-HYBRID TPE-Available per ft. HBFSS1438 STAINLESS HOSE BARB 1/4 FPT X 3/8 BARB HBSS1234 STAINLESS HOSE BARB 1/2 X 3/4 HBSS1438 STAINLESS HOSE BARB 1/4 MPT X 3/8 BARB HBSSEL1438 STAINLESS HOSE BARB ELBOW 1/4 INCH NPT X 3/8 HOSE BARB HBSSEL1814 304 STAINLESS ELBOW 1/8 INCH NPT X 1/4 INCH HOSE BARB HHPB3414 HEX HEAD POLY REDUCER BUSHING 3/4 X 1/4 HHSB1238 HEX HEAD S.S. REDUCER BUSHING 1/2in X 3/8 HV60 NV14Y NV14Y-HNDL P56 P56K P56V 20756103B HB14P HB5638 HB5638K HB5638V P56-BRKT P56-BRKT-SCREW PLPF PLPF-PIN PVCV34FM PW10 R25 ABR25 AFR25 S142058-VS SSA14 SSAXLE15 SSC38 SS-MESH SSP12 SSST SST12HB38 ST80200 STR38-IL TANK-20N TW916 W15 W387 1/2in STAINLESS BALL VALVE - w/ WELDED NUT FLOW CONTROL VALVE - INCLUDES BLACK KNOB KNOB FOR 2839-1/4 NEEDLE VALVE 5700 SANTO PUMP 5700 PUMP WITH KALREZ SEALS FLOJET G57 PUMP WITH VITON Polypro G57 Air Port x HB Straight, w/ Viton o-ring 1/4in BRASS HB AIR FITTING /G57/P56 HOSE BARB FOR P56 PUMP HOSE BARB FOR P56K PUMP HOSE BARB FOR P56V PUMP PUMP BRACKET- STAINLESS STEEL HI LO SCREW FOR RETAINING P56-BRKT PORTABLE FOAMER BACK PLATE W/ HINGE AND HOLES 302 STAINLESS PORTABLE PLATE HINGE PIN PVC VALVE 3/4in FPT X 3/4in MPT 3/4in BLACK POLY PRO X 10in - FPTBE - SCH.80 AIR REGULATOR - SILVER COLOR - 1/4fpt TWO PORT 1/8fpt TWO PORT - INCLUDES FILTER AND BOWL METAL AIR BOWL for R25 AIR FILTER for R25 1/4-20 X 5/8 PHIL TRUSS MACHINE SCREW 18-8 W/#516 VIBRASEAL ORANGE PATCH SS304 MALE/FEMALE ADAPTER 1/4 NPT X 1/4 NPT STAINLESS STEEL AXLE 15.625 INCHES LONG BY 5/8 INCH IN DIAMETER DRILLED AND BEVELED WORM GEAR CLAMP, S/S (.25-.63) STAINLESS STEEL MESH WITH SSST FOR REPLACEMENT STAINLESS STEEL AXLE PLATE - 2.5 inch X 1 inch - 2 HOLE SCREEN DISC .687 DIA. 10 X 10 MESH @ .020 DIA. 300 SERIES S.S. STAINLESS TEE COMBO 1/2in FPT X 3/8 in BARB WITH SSST AND S.S. MESH VEEJET NOZZLE, BRASS 80200 IN LINE STRAINER 3/8 BARB 20 MESH 304 STAINLESS EDPM GSKT 20 GALLON NATURAL ROTOMOLDED TANK 1/2 INT TOOTH L/W 410SS NONMARKING WHEEL FOR PORTABLE UNITS S.S. 304 SPRAY WAND 3/8in MPT X 7in LONG - THREAD ON ONE END Model No.: FI-20N, FI-20NK, FI-20NV, FI-20N-ST, FI-20NK-ST, FI-20NV-ST Page 6 of 6 | 20221205Adobe PDF Library 17.0 Adobe InDesign 18.0 (Windows)