Fast Wireless Charging Holder
Instructions
Features
- Car holder with wireless charging function, charges your phone conveniently when driving.
- Power output 5W/7.5W/10W/15W, compatible with all phones with QI standard.
- Full 360 degrees rotation for perfect viewing angle.
- Starts charging once the phone contacts the holder, no need to plug a cable into the phone.
- Auto-Adjusted foot support helps align to the charging center automatically.
Product Diagram
A diagram shows the wireless charger holder, indicating dimensions for phone compatibility (68-95 mm) and the air vent mount.
Parameters
Air vent mount: 32 mm
Charging Cable: Type C charging interface
Release button: Used to open the clamp arms.
Charging Indicator: Turns red when charging.
Product Specification
| Wireless charger holder: | |
|---|---|
| Voltage | 5V/2A 9V/2.2A |
| Output | 15W (Max) |
| Charging frequency | 115K-205KHZ |
| Induction Distance | 1-5mm |
| FCC ID | 2BQJ8-TAC-151 |
LED Mode:
| Working state | LED light color |
|---|---|
| Standby mode | The light is not bright |
| Power transfer | Red, blue, red blue light flash once, then off |
| Charging | The red light stays on for a long time |
| FOD Warning | Flashing red light |
Compatible Devices
Works well with all Qi enabled devices including:
- iPhone models (16, 16 Pro Max, 16 Pro, 15, 15 Pro Max, 15 Pro, 14, 14 Pro Max, 14 Pro, 13, 13 Pro Max, 13 Pro, 13 mini, 12, 12 Pro Max, 12 Pro, 12 mini, SE, 11, XR, X, XS, XS Max, 8, 8 Plus)
- Samsung models (Note 8, Note 9, S7 edge, S8, S8+, S9, S9+, S10, S10+, S20, S21, S22, S23, S24)
- Huawei P30 Pro
- MIUI9
- Qi disabled devices with wireless receiver or wireless charging case (Require receiver compliant with WPC Qi standard to match).
Instructions
- Insert the adjuster into the ball joint of the air vent mount. Insert the ball into the socket at the back of the bracket and turn the adjuster to tighten.
- Insert the hook into the car air outlet vane and tighten to lock. When you hear 'clatter' sounds, it means the mount has been fixed tightly.
- Connect the charging cable to the charging interface. Press the release buttons on the side, then the clamp arms and foot support will open automatically.
- Place your device into the bracket, and the clamp arms and foot support will lock it automatically, then start to charge.
- For dashboard mounting: Clean the surface thoroughly before placing the suction cup. Press firmly around the base for 5 seconds, then lock it. Wait at least 20 minutes before use. For drop-down mounting, ensure the silicone pad fully contacts the dashboard.
- For standing installation, adjust the bracket arm to your preferred viewing angle. For best stability, shorten the arm.
- After connecting the power cord, press both release buttons to auto-open the clamping arm and footrest. The stand will detect your phone, secure it, and start charging.
- For windshield mounting: Clean the surface thoroughly first. Press the base firmly for 5 seconds, then lock it. Wait at least 20 minutes before use.
Attentions
- Please use the product correctly according to instructions.
- Please do not disassemble the product or throw it into fire and water, to avoid leakage caused by electrical short circuit.
- Please do not use the wireless charger in high temperature, wet, or corrosive environments, to avoid leakage caused by damaged circuits.
- Please do not place the wireless charger close to cards with magnetic stripes or chips (ID card, credit card, etc.) to avoid demagnetization.
- Please keep the wireless charger at least 20 CM distance away from implantable medical devices (heart pacemaker, implantable cochlea, etc.) to avoid potential interferences.
- Please keep it safe, do not let children treat the wireless charger as a toy to avoid unwanted accidents.
The pictures are for reference only; please take the actual product as the standard.
FCC Statement
FCC ID: 2BQJ8-TAC-151
FCC WARNING: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The equipment complies with FCC Radiation exposure limit set forth for an uncontrolled environment. The equipment should be installed and operated with a minimum distance of 20cm between the product and your body.