Screw Fasteners | DEWALT
nVent CADDY, ERICO, ERIFLEX, LENTON New Website | nVent
Instruction Manual for ERICO models including: CSBBRS1EG Branch Line Restraint, CSBBRS1EG, Branch Line Restraint, Line Restraint, Restraint
File Info : application/pdf, 5 Pages, 1.21MB
DocumentDocumentINSTRUCTION SHEET CSBBRS1EG Branch Line Restraint, Structural Attachment Fitting for steel 12 gauge (0.1094"[2.78mm] to 0.50"[12.7mm] thick NA Part Number CSBBRS1EG CSBBRS1MEG CSBBRS1EG CSBBRS1MEG EU Article Number --402239 --402239 Rod Size 3/8" M10 1/2" M12 UL® Load Rating 425 lbs (1891N) 45 - 59 310 lbs (1380N) FM® Load Rating 60 - 74 210 lbs (935N) 290 lbs (1290N) 200 lbs (890N) 75 - 90 210 lbs (935N) 220 lbs (980N) Rod Root Least Radius of Gyration Maximum Unbraced Length (L) Size Dia. r L/r = 100 L/r = 200 L/r = 300 L/r = 400* 3/8" 0.300" 0.075" 7" 14" 22" 30" M10 7.94mm 1.99mm 198mm 397mm 595mm 794mm 1/2" 0.404" 0.101" 10" 20" 30" 40" M12 9.60mm 2.40mm 240mm 480mm 720mm 960mm Refernece: NFPA®13, (2007) *Reference: NFPA13, (2010) 1. Orient part in the direction needed for installation. 2. Install with a standard screw gun with a depth sensitive nosepiece or clutch for correct seating of fastener. Use a size 5/16" [8mm] hex head on drill & tap screw. 1/2" min Install top/bottom flanges or web Branch Line Restraints are intended to be installed in accordance with NFPA®-13 and manufacturer's installation instructions. WARNING: 1. ERICO products shall be installed and used only as indicated in ERICO product instruction sheets and training materials. Instruction sheets are available at www.erico.com and from your ERICO customer service representative. 2. ERICO products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings. 3. All instructions must be completely followed to ensure proper and safe installation and performance. 4. Improper installation, misuse, misapplication or other failure to completely follow ERICO's instructions and warnings may cause product malfunction, property damage, serious bodily injury and death. 5. Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment. 6. All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any other purpose. NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted. The customer is responsible for: a. Conformance to all governing codes. b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified engineer. c. Using appropriate industry standard hardware as noted above. SAFETY INSTRUCTIONS: All governing codes and regulations and those required by the job site must be observed. Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application. ELCO is a registered trademark of Asia Fastening (US), Inc. FM is a registered certification of FM Approvals LLC, LTD. NFPA is a registered trademark of National Fire Protection Association, Inc. UL is a registered trademark of UL LLC. CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation. TECHNICAL SUPPORT: www.erico.com CFS450_E 1 OF 5 © 2011, 2012, 2013 ERICO International Corporation. INSTRUCTION SHEET CSBBRS1EG Branch Line Restraint, Structural Attachment Fitting for steel 12 gauge (0.1094"[2.78mm] to 0.50"[12.7mm] thick 3. Rotate barrel to 3/8"-16 or 1/2"-13, based on threaded rod needed for application. ELCO® part number ECC720 for more information go to www.elcoconstruction.com 3/8"-16 side A A B 1/2"-13 side B Correct installation Incorrect installation SECTION A-A 4. Fully thread rod into barrel nut. SECTION B-B Rod not fully threaded into barrel nut. CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation. TECHNICAL SUPPORT: www.erico.com CFS450_E 2 OF 5 © 2011, 2012, 2013 ERICO International Corporation. INSTRUCTION SHEET CSBBRS1EG Branch Line Restraint, Structural Attachment Fitting for steel 12 gauge (0.1094"[2.78mm] to 0.50"[12.7mm] thick This product is intended to be used as a restraint and not a hanger. CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation. TECHNICAL SUPPORT: www.erico.com CFS450_E 3 OF 5 © 2011, 2012, 2013 ERICO International Corporation. INSTRUCTION SHEET CSBBRS1EG Branch Line Restraint, Structural Attachment Fitting for steel 12 gauge (0.1094"[2.78mm] to 0.50"[12.7mm] thick This product is intended to be used as a restraint and not a hanger. CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation. TECHNICAL SUPPORT: www.erico.com CFS450_E 4 OF 5 © 2011, 2012, 2013 ERICO International Corporation. INSTRUCTION SHEET CSBBRS1EG Branch Line Restraint, Structural Attachment Fitting for steel 12 gauge (0.1094"[2.78mm] to 0.50"[12.7mm] thick This product is intended to be used as a restraint and not a hanger. CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation. TECHNICAL SUPPORT: www.erico.com CFS450_E 5 OF 5 © 2011, 2012, 2013 ERICO International Corporation.