SRP FORMULA-R Sim Racing Pedals

1. GENERAL INFORMATION

1.1. User Cautions

Please read the safety and warning notes in this manual before using the pedals. Following these instructions is essential for issue-free operation and to be eligible for warranty claims. The pedals are designed for a specific purpose; any other use is considered dangerous. The manufacturer is not liable for damages resulting from non-compliance with the manual's instructions. This manual contains important operational information and should always be kept accessible.

1.2. Manufacturer's Details

Sim Racing Pro 2018 S.L.
Carretera de Tordera, 89
17300 Blanes (Girona)
Spain
Tel: +34 627 639 716
Email: info@simracing-pro.com

1.3. Technical Service Details

Sim Racing Pro 2018 S.L.
Carretera de Tordera, 89
17300 Blanes (Girona)
Spain
Tel: +34 627 639 716
Email: support@simracing-pro.com

2. DESCRIPTION OF THE PEDALS

2.1. General Description

This manual provides all necessary instructions for the installation, commissioning, maintenance, and use of the pedals. The product consists of a base, three pistons, and a set of three pedals: accelerator, brake, and clutch.

Components

One Base, 3 pistons, set of three pedals (accelerator, brake, and clutch).

Electrical Power Supply

Power and electricity consumption: 5 Volts USB-C
Model: Sim Racing Pro
Total Power: 225mW
Total consumption: 45mAh

Note: These consumptions are approximate and depend on the performance of each element.

2.2. What's Included

• Set of pedals
• 1 pc Allen key nº3
• 1 pc Allen key nº4
• 1 pc Allen key nº5
• 1 pc. 10 mm open-end wrench
• 1 pc open end wrench 13 mm
• 1 x 2m USB cable (USB-C to USB-A)
• 1 user manual / CE certificate
• 1 Warranty form

2.3. Working Principle

The SRP GT 3p/2p pedals are designed for Driving Simulation.

2.4. Intended Use

The pedals are intended for driving simulation when playing PC car racing games. Do not use them for any other activities or with elements not indicated herein. Exceeding the pedals' working capacity may void the manufacturer's responsibility for any resulting damage.

2.5. Important Safety Precautions

Pedals may be suitable for children over six years old with appropriate adult supervision. Proper fastening is essential for correct functioning. Appropriate use and maintenance contribute to the equipment's longevity.

2.6. Control Panel

Refer to section 7.3 for control panel details.

2.7. Important Safety Symbols

Symbols found on the pedals include:

• DANGER! Electrical risk: Indicates electrical risk in the electrical panel and indicated areas. [⚡]

Note: Ensure all identification signs and warning plates are maintained and preserved. Do not dismantle or alter them under any circumstances.

3. WARNINGS AND SAFETY INSTRUCTIONS

3.1. Protection and Safeguards

The materials used are not hygienic risks, but plastic components and lubricants may generate toxic fumes in case of fire. Do not perform maintenance or cleaning operations on the pedals or surrounding areas without first disconnecting the USB connection.

4. STORAGE AND TRANSPORT

4.1. Receiving the Pedals

Upon receipt, check the pedals for any damage incurred during delivery.

4.2. Weight and Dimensions

Refer to general dimensional drawing 9.1.

4.3. Storage

No specific storage measures are required. If the pedals are to be unused for an extended period, it is recommended to protect them from dust by covering them and disconnecting them from any power source.

4.4. Transport and Handling

Ensure the manual is available when moving the pedals. Consider the total weight of the pedals for transportation.

5. DIMENSIONS

Note: This product is designed for assembly by the end-user.

Standard Fastening SRP

Diagram Description: Shows a base plate with mounting holes. Dimensions provided are 347mm (width) and 330mm (length). It indicates the use of M6 through bolts and recommends using at least 4 clamping points.

Equivalent Fastening to G25 / G27 / G29

Diagram Description: Shows an alternative mounting pattern with dimensions 204.02mm (width) and 186.00mm (height). It specifies M6 thread with a maximum depth of 8mm.

5.1. Unpacking

Upon receipt, unpack the pedals with care, preferably near their final location. Do not install if any damage is observed. If in doubt, refrain from use and contact the supplier.

5.2. Setup Location

The surface must support the pedals' weight (as per section 4.1). Pedals are best placed on a metal frame for secure fixing, or directly on the floor on a carpet or rubber surface.

5.3. Assembly

Once the product is in its working location, it can be installed and connected.

5.4. Electrical Connection

The pedals connect via USB and require a stable, standardized 5V supply voltage within the specified operating ranges. Faulty power supply can lead to malfunction or damage to electrical components. Ensure all connecting cables are protected and not left in inconvenient areas.

Diagram Description: Illustrates the rear of the pedal base showing the connections for THROTTLE, BRAKE, CLUTCH, and the USB-C port.

6. BEFORE YOU START

6.1. Fastening

Ensure the pedals are levelled correctly as described in section 5.3.

6.2. Review with Pedals Connected

Diagram Description: Shows the pedal base with various LEDs. The text describes the function of each LED:

• POWER: Red LED indicating USB power.
• WARNING: Orange LED for failure indication.
• INI-OK: Green LED indicating data communication with the PC.
• THROTTLE: Blue LED indicating throttle piston status.
• BRAKE: Blue LED indicating brake piston status.
• CLUTCH: Blue LED indicating clutch piston status.
• BRAKE REGULATOR: Blue LED indicating brake adjustment activation.

7. INSTRUCTIONS FOR USE

7.1. Pre-inspection and Adjustments

• Before use, check that the pedals are connected correctly.
• Verify the status of the LED indicators for correct operation (see point 6.2).

7.2. Controls

The pedals typically include an accelerator, a brake, and a clutch, depending on the model.

7.3. CONTROL SETTINGS

Key Adjustment

There are 9 positions for the keys. Unscrew the two Allen screws to move them.

Cam Angle Adjustments

By unscrewing the two screws labeled 'A', the cams can be adjusted in the range of 70° to 90°. Recommendations: 70° for GT seating position, 90° for Formula (lying down) position. This applies to the accelerator, brake, and clutch cams.

Firmness Adjustments

Loosen screw 'B' to raise the piston for more firmness, or lower it for less firmness. This adjustment is applicable to all three pistons (accelerator, brake, and clutch).

Brake Travel Adjustments

Using the 13 mm spanner, turning screw 'A' to the left shortens the travel to a minimum of 15 mm. Turning it to the right increases travel up to a maximum of 45 mm. After setting the desired travel, perform a calibration via the application to reset the minimum value and then manually adjust the maximum value for braking pressure.

Throttle Travel Adjustments

By loosening hexagon socket screw 'C' (and unscrewing part 'D'), the throttle route is shortened. Unscrew a maximum of 15 mm. The pedal is supplied at its maximum route.

Diagram Description: Illustrates three stages of throttle travel: *Maximum stroke, *Standard stroke, and *Minimum stroke, showing the mechanical adjustment.

7.4. Download and Use of the App

Download the app from the Download section on the SRP website. Execute and follow the application's steps for optimal configuration.

Diagram Description: Shows a screenshot of the SRP-MySetup V3.0 application interface, displaying firmware version, profile, mode (PRO/CUSTOM), and various control buttons like 'BASIC SETTINGS', 'ACTIVATE PRO MODE', 'ADVANCED SETTINGS', 'OPEN MONITOR', 'LANGUAGE', 'MANUAL', 'OPEN VR MONITOR', and 'EXIT'.

8. MAINTENANCE

8.1. General Cleaning

It is advisable to clean the pedals periodically to remove dust. Do not use cleaning fluids on the plate area, as this could damage the pedals. Regular cleaning and maintenance help maintain optimal performance and product longevity.

8.2. Replacement of Elements

Any element replacement must be performed by technical service or via remote connection with technical service. Ensure the power supply is fully disconnected before performing any maintenance or cleaning operations on the pedals or attached devices.

9. ATTACHMENTS

9.1. General Measures Diagram

Diagram Description: Provides overall dimensions of the pedal set. One view shows the side profile with dimensions like 245.09mm and 162.04mm. Another view shows the top/bottom layout with dimensions like 441.21mm.

10. DECLARATION OF CONFORMITY

Declaración de conformidad

Company: Sim Racing-Pro S.L.
Address: Carretera de Tordera nº 89, 17300 BLANES (Girona), Spain
Product: Pedales de Simulación
Model: [Model not specified in this section]
Serial Number: [Not specified]
Year of Manufacture: [Not specified]

In conformity with the following regulations:

• 2006/42/CE Machinery Directive
• 2006/42/CE Directive relating to machinery.
• 2006/95/CE Low Voltage Directive.
• 2004/108/CE Electromagnetic Compatibility Directive.

We declare that the indicated machine complies with the essential health and safety requirements of the European Community's Machinery Directive. This Declaration of Conformity will lose its validity if the machine is modified without prior agreement or authorization from Sim Racing-Pro S.L.'s Technical Service.

Date: Blanes, July 1, 2020

Signatory: Sra. Leidy Quintero, LEGAL REPRESENTATIVE, SIM RACING-PRO 2018 S.L.

11. "CE" BRANDING

The plate is stamped with the manufacturer's brand, the CE conformity brand, and the manufacturer's social information. Specific details like brand, model, serial number, and year of manufacture are displayed on the top of the plate.

12. WARRANTY

Sim Racing Pro 2018, S.L. is committed to ensuring the proper functioning of the pedals and replacing elements due to manufacturing defects. The warranty is valid as long as the pedals have not been distorted or varied through normal operation, and the faulty element has NOT BEEN MISHANDLED OR MANIPULATED. The warranty period is 2 years from the date of billing, excluding electrical components and parts subject to normal wear and tear.

13. TECHNICAL DOCUMENTATION

List of documentation included:

Paper support:

• Instruction Manual
• CE Declaration of Conformity (included in the manual)
• Warranty sheet (included in the manual)