Instruction Manual for COMMAND ACCESS TECHNOLOGIES models including: LPM190 Series Mortise Lock, LPM190 Series, Mortise Lock, Lock
Command Access Mortise Lock
LPM190 Series INSERT INSTRUCTIONS Optional: LPM193-198 A B Optional: REX OR LBM Kit Includes A. 1-LPM19X Series Mortise Lock B. 1- 51056 - 2 Position 48" Wire Harness C. 1- 50436 - 2 Position 8' Wire Harness (LPM193-98)* TOOLS REQUIRED · Chisel/Wood rasp File · 1" Spade Bit SPECIFICATIONS Latch retraction · Input Voltage: 24VDC +/- 10% · AVERAGE LATCH RETRACTION CURRENT: 1A · Average holding current: 300 ma · Wire gauge: Minimum 18 gauge · Direct wire run - no relays or access control units in-between power supply & lock Lever Control · Input Voltage: SPECIFY 24VDC or 12VDC +/- 10% · CURRENT 24V = 350mA · Current 12V = 700mA Optional built-in SWITCHES SPDT - Rated .5a @24V REX · · · lbm · · · green= Common (C) Blue = normally open (NO) grey = normally closed (NC) green/BLK= Common (C) Blue /BLK= normally open (NO) grey/BLK = normally closed (NC) R e c o m m e n d e d P o w e r S u p p l i e s : Use a power limited class 2 power supply All Command Access exit devices & field installable kits have been thoroughly cycle tested with Command Access power supplies at our factory. If you plan on using a non-Command power supply it must be a filtered & regulated linear power supply. U.S. Customer Support 1-888-622-2377 Visit our website for more details www.commandaccess.com Canada Customer Support 1-855-823-3002 Ceiling Tile Installation Instructions CAT GREEN CHANNEL 1 LED CAT LOCKING HARDWARE OPERATOR NORMALLY OPEN DRY CONTACT FROM ACCESS CONTROL SYSTEM NO VOLTAGE LOCKING + HARDWARE - NORMALLY OPEN DRY CONTACT FROM ACCESS CONTROL SYSTEM NO VOLTAGE LOCKING + HARDWARE - "B"wire LPM1 Series Installation Example Standard Wire Run Optional Wire Run 1. The door must be prepared according to our LPM190 template and a 3/8" wire raceway. Be sure that the mortise pocket and the raceway are clear of debris prior to installation. 2. Install the "B" wire through the wire raceway leaving enough slack to "quick connect" to the mortise chassis. 3. Hardware wire "B" directly to electric hinge (CAT ETH4WH or 420W) or other transfer device, 18ga wire min. 4.Connect the wire run coming from the 26.5VDC power supply (not included - PS220 or PS210) into power transfer. The power supply may be up to 300 feet away (see power supply wiring instructions). Note: these wires are not polarity sensitive. US customer support 1-888-622-2377 | www.commandaccess.com | CANADA customer support 1-855-823-3002 Installation Instructions For Lever Control Solenoid on LPM models 193-198 Only 1. The door must be machined with a 3/8" wire raceway, mortise lock pocket & prepped for a energy transfer hinge. Make sure the mortise pocket is free of debris. 2. Run the wires from the ETH hinge through the 3/8" raceway starting at the ETH hinge & exiting into the mortise pocket. Mortise Lock Pocket Mortise Lock Pocket ETH Hinge Pocket 3/8 Wire Raceway Wire Transfer Hinge 3/8 Wire Raceway 3. Screw the ETH hinge to the door. At this time DO NOT connect the hinge wires on the jamb side to the wires coming from the power supply. 1 2 3 4 4. Connect the wires exiting the mortise pocket to the Bridge Rectifier (included). Bridge Rectifier Mortise Lock Pocket Wire Transfer Hinge 5.Connect the Bridge Rectifier to the plug exiting the mortise chassis. 6. Carefully slip the connected mortise lock chassis into the mortise pocket paying close attention not to pinch any wires. Bridge Rectifier Mortise Lock Pocket Mortise Lock Pocket ETH Hinge Pocket Plug Plug 3/8 Wire Raceway 7. Mount the chassis per manufacturer's instructions. 8. Connect the wires from the power supply at the ETH hinge on the jamb side. Connect the hinge to the jamb. EU (Fail Secure) Bridge Rectifier EL (Fail Safe) Bridge Rectifier Energy Transfer Hinge Switch EU (Fail Secure) 12VAC/DC or 24VAC/DC Energy Transfer Hinge Switch EL (Fail Safe) Power Supply 12VAC/DC or 24VAC/DC Power Supply US customer support 1-888-622-2377 | www.commandaccess.com | CANADA customer support 1-855-823-3002 Installation Instructions HOW TO CHANGE HANDING 1. Locate the handing screw. This screw is used to hand the handles. The Locking side is opposite the screw. 2. To hand the latchbolt, remove the faceplate. Pull the latchbolt out of the chassis and rotate, then release. The latchbolt is spring loaded and will return on it's own. LH/LHR RH/RHR Rotate 180 Deg. 1-1/8" MOTOR NOTCH 2" 1" Handing Screw 2" Template for LPM190 Series Mortise Locks *Additional MOTOR Notch Only required for wood doors 1-1/4" diameter cylinder hole for exterior side only 5/8" diameter thumb turn hole for interior side only 3/8" diameter through hole 1" diameter through hole 3/8" diameter through hole 2-9/64" 1" 6-1/8" 1-3/16" 1-23/32" 2-1/4" 2-7/32" 2-3/4" 3-9/32" 4-5/8" US customer support 1-888-622-2377 | www.commandaccess.com | CANADA customer support 1-855-823-3002Adobe PDF Library 16.0.3 Adobe InDesign 17.0 (Macintosh)