User Manual for Ceatidential models including: 2A38M-OTMA01, 2A38MOTMA01, OTM-A01 Bluetooth Audio Device, OTM-A01 Audio Device, Bluetooth Audio Device, Audio Device, Bluetooth Device, Device
ALPINE ELECTRONICS MARKETING, INC. OTMA01 Auto EQ Bluetooth Audio Transmitter 2A38M-OTMA01 2A38MOTMA01 otma01
ALPINE ELECTRONICS MARKETING, INC. OTMA01 2A38M-OTMA01 2A38MOTMA01 otma01
OTM-A01 Product Summary 2024/4/22 Product Summary Product form Product Name Bluetooth Audio Device OTM-A01 Power Supply USB-C(USB2.0) Input/output system Input Bluetooth Audio USB-Audio USB Bus Power BLE: 2.402GHz~2.480GHz Output Bluetooth: 2.402GHz~2.480GHz AUX (3.5mm TRS JACK) Intended use Automotive & Home Use Bluetooth Version BT-Rx Bluetooth v5.2 BT-Tx Bluetooth v5.3 BT-Rx Class2 Bluetooth Class BT-Tx Class2 Power Power Class 2 Operating temperature range -20degC ~ +60degC Storage temperature range -40degC ~ +85degC This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modification warning.Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be colocated or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). RF Exposure Information This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator and your body NOTE To satisfy FCC requirements. This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: "Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device." Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L' exploitation est autorisée aux deux conditions suivantes : 1) l'appareil ne doit pas produire de brouillage; 2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. WDP1_How to use (usual action) BT-Rx to BT-Tx Bluetooth BT-Rx BT-Tx Bluetooth JBL GO2 iPhone SE3 USB Power USB-A to C Cable Apple 10W Power ON WDP1 operates on USB Bus Power, so it is Power ON when USB power is supplied to USB Power. When not powered, it will be Power OFF. USB-Audio to LINEOUT iPhone SE3 JBL GO2 LINE INPUT USB Audio Apple Lightning-USB USB-A to C Cable USB AUX OUT 3.5mm TRS CABLE USB-A to C Cable Apple 10W Power ON Indicator Blue LED (LED lighting:Power ON) Connect to USB Power Bluetooth connection between BT-Rx and iPhone SE3 When the LED flashes, it is BT-Rx Pairing Mode. (LED Flashing:Pairing) LED changes from blinking to lit when connection is complete. Press 5~10sec Pairing Key Once the WDP1 BT-Rx is in paired mode, the "ALPINE WDP1 RX" will appear on the iPhone SE3 Bluetooth connection screen. Bluetooth connection between BT-Tx and JBL GO2 When the LED flashes, it is BT-Tx Pairing Mode. (LED Flashing:Pairing) Press 10sec~ Pairing Key Play Sine Wave Launch Signal gen APP on iPhone SE3 Tap to Play Sine Wave Pairing by short press of Pairing button. Indicator switches from slow blinking to fast blinking. Power ON by short press of power button. Indicator glows with slow flashing light. Indicator LED LINE INPUT USB Charge Port Once the WDP1 and JBL GO2 are in pairing mode, position them close to each other for connection. Once the WDP1 and JBL GO2 are in pairing mode, position them close to each other for connection. Manipulate the volume on the JGL GO2 to set the minimum audible sound level. Set to 1000.0Hz Set to +0.0dB LED changes from blinking to lit when connection is complete. About USB-Audio and AUX OUT connections for USB-Audio, connect the iPhone to the Lightning-Camera adapter, connect the camera adapter to the USB-A to C cable, and connect it to the USB-Audio connector on the WDP1. for AUX OUT, connect the WDP1 AUX OUT to the JBL GO2 LINE INPUT using a 3.5mm TRS cable.WPS 表格