User Manual for NORMAN models including: DIAL01 Remote Control, DIAL01, Remote Control, Control, Remote
N301502-Model#DIAL01遙控器說明書-QR Code版本 re02
Step 2: Remove the Battery Cover. Step 3: Replace CR2032 3V batteries. Step 4: Put the battery cover and Color ring back. Step 5: Remote lights will illuminate after proper installation. When pressing “ALL” button, the button will light up and you can then operate all shades that are programmed to the remote at once.
File Info : application/pdf, 15 Pages, 1.44MB
DocumentDocumentRemote Control Model# DIAL01 PRODUCT SPECIFICATION 1. ModelDIAL01 2. DimensionsOD 67.6mm x H 21.2mm 3. Weight (including battery)74.5g ± 20g 4. Battery/VoltageCR2032 3V x 2 5. Radio Frequency proprietary 2.4 GHz 6. Operation Temperature : 0°C - 50°C / 32°F - 122°F FCC ID: Q3V-DIAL01 IC: 28542-DIAL01 FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Unauthorized modifications may void the user's authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. N301502 IC Information Innovation, Science and Economic Development Canada (ISED) Notices This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Canada, avis d'Industry Canada (ISED) Cet appareil contient un ou des émetteurs/récepteurs exempts de licence conformes aux RSS exempts de licence d'Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis aux deux conditions suivantes: 1. Cet appareil ne doit pas causer d'interférences. 2. Cet appareil doit accepter toutes les interférences, y compris les interférences pouvant entraîner un fonctionnement indésirable de l'appareil. CAN ICES-003(B) / NMB-003(B) RF Exposure Warning The equipment complies with FCC/ISED RF exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter. BUTTON OVERVIEW Move Shade to Fully Open Setup Best Privacy Control All Channels Stop My Favorite Best View Shade Channel (There are 5 channels) Move Shade to Fully Closed The function of buttons may vary depending on the shade type, please refer to section "OPERATION". REPLACE BATTERY CHANNEL BUTTON INTRODUCTION SELECT ONE CHANNEL When you select a channel (1~5), the selected channel will light up, and you can then operate the shade(s) that are programmed to this channel. Color Battery CR2032 3V Ring Cover Batteries Step 1: Remove the Color ring. Step 2: Remove the Battery Cover. Step 3: Replace CR2032 3V batteries. Step 4: Put the battery cover and Color ring back. Step 5: Remote lights will illuminate after proper installation. GROUP CONTROL When pressing "ALL" button, the button will light up and you can then operate all shades that are programmed to the remote at once. OPERATION Lift Feature Button Function Bottom Up (Cellular Shade / Roller Shade / Roman Shade) Top Down Bottom Up (Cellular Shade) Day & Night (Cellular Shade) Pefect Sheer Best Privacy Fully close for best privacy. Fully close for best privacy. Fully close for best privacy. Fully close for best privacy. Best View Fully open for best view. Fully open for best view. Fully open for best view. Fully open for best view. My Favorite Move to "My Favorite" pre-set position. Default "My Favorite" position: 1/2 of shade height. Move to "My Favorite" pre-set position. Default "My Favorite" position: 1/2 of shade height. Move to "My Favorite" pre-set position. Default "My Favorite" position: 1/2 of shade height. Move to "My Favorite" pre-set position. Default "My Favorite" position: 1/2 of shade height. Counterclockwise Dial Slightly adjust shade position to close. Slightly move middle rail to close. When dial more than 90°, middle rail will continously move to close. Middle rail will stop when it fully closed to bottom rail. Keep dialing the remote, middle rail and bottom rail will move down together. Slightly move middle rail to close. When dial more than 90°, middle rail will continously move to close.Middle rail will stop when it fully closed to bottom rail. Keep dialing the remote, middle rail and bottom rail will move down together. When shade is not fully closed, slightly tilt to make bottom rail lowered a bit. Turn over 90° to make shade fully closed. When shade is fully closed, slightly tilt to make vane opened a bit. Turn over 90 degrees to make vane fully opened. Clockwise Dial Slightly adjust shade position to open. Slightly move middle rail to open. When dial more than 90°, middle rail will continously move to open. Slightly move middle rail to open. When dial more than 90°, middle rail will continously move to open. When vane is opened, slightly tilt clockwise to make vane closed a bit. Turn over 90° to make shade fully closed. When shade is fully closed, slightly tilt to make bottom rail raised a bit. Turn over 90° to make shade fully raised. Fully Close Continuously move shade to close. Continuously move bottom rail to close. Continuously move bottom rail to close. Move shade to fully closed/ When adjusting vane openness, press 1 time and shade will be fully lowered down and closed. Press again and vane would be opened. Fully Open Continuously move shade to open. Continuously move bottom rail to open. Bottom rail will stop when it fully close to middle rail. Press this button again, bottom rail and middle rail will move up together. Continuously move bottom rail to open. Bottom rail will stop when it fully close to middle rail. Press this button again, bottom rail and middle rail will move up together. Move shade to fully open. When adjusting vane openness, press 1 time and shade will be fully closed. Press again and shade would be fully rolled up. Catalogue · PAIRING REMOTE WITH SHADE 01 · CLEAR PAIRING REMOTE WITH SHADE 02 · SET MY FAVORITE POSITION 03 · CLEAR MY FAVORITE POSITION 04 · SET UPPER LIMIT 05 · CLEAR UPPER LIMIT 06 · SET LOWER LIMIT 07 · CLEAR LOWER LIMIT 08 · SET VANE OPEN POSITION(ONLY FOR PERFECT SHEER) 09 · CLEAR VANE OPEN POSITION(ONLY FOR PERFECT SHEER) 10 · COPY REMOTE 11 · FACTORY RESET FOR COPY REMOTE 12 PAIRING REMOTE WITH SHADE Shades are pre-programmed to the designated channel / group according to your order details. If you want to change the pre-setting, please CLEAR pre-setting first (please refer to page 2) , then follow the below steps to set up a new pairing. IMPORTANT! Please only pair shades with the same lift type to the same channel for optimal operation. Step 1: On Shade x3 SHADE BUTTON Honeycomb Shade Roman Shade, Roller Shade & PerfectSheer: AC Adapter Press shade button 3 times. The green light will start blinking, while shade is ready for pairing. Roller Shade: Rechargeable Battery with Charging Wand Roman Shade, Roller Shade & PerfectSheer: Rechargeable Battery with AC Adapter Step 2: On Remote SET BUTTON 3 SECS Press and hold SET button for 3 seconds, and center buttons will blink, the remote is in SETUP mode. Step 3: Pairing Remote with Shade Shade Response Paired successfully Jog x 1 Choose a desired channel. The selected channel will light up. SET BUTTON 3 SECS Press and hold SET button for 3 seconds, and the center buttons will stop blinking. Then, the remote exits SETUP mode. i SETUP mode will time out after 20 seconds of inactivity. 01 CLEAR PAIRING REMOTE WITH SHADE Step 1: On Shade x3 SHADE BUTTON Honeycomb Shade Roman Shade, Roller Shade & PerfectSheer: AC Adapter Press SHADE BUTTON 3 times. The green light will start blinking, while shade is ready for pairing. Roller Shade: Rechargeable Battery with Charging Wand Roman Shade, Roller Shade & PerfectSheer: Rechargeable Battery with AC Adapter Step 2: On Remote SET BUTTON 3 SECS Press and hold SET button for 3 seconds, and center buttons will blink, the remote is in SETUP mode. Step 3: Clear remote with Shade Shade Response Clear pairing remote with shade successfully Jog x 2 Choose the channel which belongs to the shade you would like to unpair from your remote. The selected channel will light up. SET BUTTON 3 SECS Press and hold SET button for 3 seconds, and the center buttons will stop blinking. Then, the remote exits SETUP mode. i SETUP mode will time out after 20 seconds of inactivity. 02 SET MY FAVORITE POSITION Please press "My Favorite" to check the default position setting, if you would like to change My Favorite position, you could follow below procedures. CAUTION! To avoid an accidental setup with other shades: Please power off other shades first, or pair the designated shade in a separate channel. Then proceed to set up or clear your desired settings. Step 1: Move the shade to desired position. Step 2: Press and hold SET button for 3 seconds, and center buttons will blink. SET BUTTON 3 SECS Step 3: Choose the channel which is paired to the shade. The selected channel will light up. Step 4: Press button to save My Favorite position. Setup Success Shade Response Jog x 1 03 CLEAR MY FAVORITE POSITION If you clear My Favorite position, and do not set a new one, My Favorite position will reset back to default position which is 1/2 the length of the shade. CAUTION! To avoid an accidental setup with other shades: Please power off other shades first, or pair the designated shade in a separate channel. Then proceed to set up or clear your desired settings. Step 1: Press and hold SET button for 3 seconds. The center buttons will blink. SET BUTTON 3 SECS Step 2: Choose the channel which is paired to the shade. The selected channel will light up. Step 3: Press and hold button to clear My Favorite. The shade will jog twice and return to default Favorite position. Setup Success Shade Response Jog x 2 04 SET UPPER LIMIT Shades upper limit has been set before shipping out from factory. If you want to change the pre-setting, please CLEAR the upper limit first (please refer to page 6) , then follow below steps to set up new upper limit. CAUTION! To avoid an accidental setup with other shades: Please power off other shades first, or pair the designated shade in a separate channel. Then proceed to set up or clear your desired settings. Step 1: Move the shade bottom rail to desired position. But for cellular Shade Motorized Day & Night, please always move both middle rail and bottom rail to desired position. Step 2: Using a pin (not provided), press and hold the RESET button for 1 second. The center buttons will start blinking - the remote is now in RESET mode. 1 SEC Step 3: Choose the channel which is paired to the shade. The selected channel will light up. Step 4: Press OPEN BUTTON open button to save upper limit. Setup Success Shade Response Jog x 1 05 CLEAR UPPER LIMIT If the upper limit hasn't been set successfully, the Best View, Best Privacy, and My Favorite function can't work optimally. CAUTION! To avoid an accidental setup with other shades: Please power off other shades first, or pair the designated shade in a separate channel. Then proceed to set up or clear your desired settings. Step 1: Using a pin (not provided), press and hold the RESET button for 1 second. The center buttons start blinking - the remote is now in RESET mode. 1 SEC Step 2: Choose the channel which is paired to the shade. The selected channel will light up. Step 3: Press and hold OPEN BUTTON 1 SEC open button for 1 second to clear upper limit. Setup Success Shade Response Jog x 2 06 SET LOWER LIMIT Shades lower limit has been set before shipping out from factory. If you want to change the pre-setting, please CLEAR the lower limit first (please refer to page 8) , then follow below steps to set up new lower limit. CAUTION! To avoid an accidental setup with other shades: Please power off other shades first, or pair the designated shade in a separate channel. Then proceed to set up or clear your desired settings. Note: Lower limit for for Perfect Sheer---Shade is fully lowered and vane is fully opened. Step 1: Move the shade to desired position. For Perfect Sheer, move the shade to vane fully opened position. Step 2: Using a pin (not provided), press and hold the RESET button for 1 second. The center buttons will start blinking - the remote is now in RESET mode. 1 SEC Step 3: Choose the channel which is paired to the shade. The selected channel will light up. Step 4: Press CLOSE BUTTON close button to save lower limit. Setup Success Shade Response Jog x 1 07 CLEAR LOWER LIMIT If the lower limit hasn't been set successfully, the Best View, Best Privacy, and My Favorite function can't work optimally. CAUTION! To avoid an accidental setup with other shades: Please power off other shades first, or pair the designated shade in a separate channel. Then proceed to set up or clear your desired settings. Step 1: Using a pin (not provided), press and hold the RESET button for 1 second. The center buttons will start blinking - the remote is now in RESET mode. 1 SEC Step 2: Choose the channel which is paired to the shade. The selected channel will light up. Step 3: Press and hold CLOSE BUTTON 1 SEC close button for 1 second to clear lower limit. Setup Success Shade Response Jog x 2 08 SET VANE OPEN POSITION(ONLY FOR PERFECT SHEER) Vane open position has been set before shipping out from factory. If you want to change the pre-setting, please CLEAR the vane open position first (please refer to page 10) , then follow below steps to set up vane open position. CAUTION! To avoid an accidental setup with other shades: Please power off other shades first, or pair the designated shade in a separate channel. Then proceed to set up or clear your desired settings. Step 1: Move the shade to desired position. Step 2: Using a pin (not provided), press and hold the RESET button for 1 second. The center buttons will start blinking - the remote is now in RESET mode. 1 SEC Step 3: Choose the channel which is paired to the shade. The selected channel will light up. Step 4: Press SET button to save vane open position. SET BUTTON Setup Success Shade Response Jog x 1 09 CLEAR VANE OPEN POSITION(ONLY FOR PERFECT SHEER) CAUTION! To avoid an accidental setup with other shades: Please power off other shades first, or pair the designated shade in a separate channel. Then proceed to set up or clear your desired settings. Step 1: Using a pin (not provided), press and hold the RESET button for 1 second. The center buttons will start blinking - the remote is now in RESET mode. 1 SEC Step 2: Choose the channel which is paired to the shade. The selected channel will light up. Step 3: Press and hold SET button for 1 second to clear vane open position. SET BUTTON Setup Success Shade Response Jog x 2 1 SEC 10 COPY REMOTE Copy all settings from the existing remote to a new remote. New Remote 1 Press and hold RESET button for 1 second by pin (not provided), center buttons will start blinking. 2 Press RESET button 3 times, center buttons will flash quickly. 1 SEC Existing Remote SET BUTTON 3 SECS 3 Press and hold SET button for 3 seconds, the center buttons will start blinking. 4 Press SET button 3 times, the channel lights will blink 4 times. Copy Success New Remote All of channel lights will light up for 1 second, and exit out of RESET mode. Existing Remote Press and hold SET button for 3 seconds and the center buttons will stop blinking and exit out of SETUP mode. 11 FACTORY RESET FOR COPY REMOTE CAUTION! By performing FACTORY RESET, your copied remote will be erased. The connection between your existing remote and hub will be disconnected. But you can still use the existing remote to operate the paired shades. Step 1: Press and hold RESET button for 1 second by pin (not provided). The center buttons will start flashing and enter RESET mode. 1 SEC Step 2: Press RESET button 6 times, the channel lights will flash 4 times, then the center buttons will start blinking. PRESS x 6 Step 3: Press and hold RESET button for 1 second, and exit out of RESET mode. 1 SEC 12GPL Ghostscript 9.55.0 Adobe Illustrator 28.1 (Windows)