Duratech | Homepage
Instruction Manual for DURATECH models including: DVP050 Vision Pro Moonlight, DVP050, Vision Pro Moonlight, Pro Moonlight, Moonlight
Duratech |
File Info : application/pdf, 24 Pages, 1.37MB
DocumentDocumentManual DVP050 DVP100 DVP170 Visit www.duratech.be for other available languages Pro 06-03-23 2 Table of contents Technical specifications Remarks Box contents Installation instructions Installation specialties Wiring instructions setup 1 Wiring instructions setup 2 Wiring remarks Synchronizing Color programs Troubleshooting Page 4 Page 5-6 Page 7 Page 10-11 Page 12-13 Page 14-15 Page 16-17 Page 18-19 Page 20 Page 21 Page 22 3 ENG Technical specifications Lamp Type DVP050-RGBW DVP100-RGBW DVP170-RGBW Description All colours and Tunable white All colours and Tunable white All colours and Tunable white Voltage Power Color temp 10-14 VAC 33 W n.a. Luminous flux* 1200 lm 10-14 VAC 85 W n.a. 3500 lm 10-14 VAC 180 W n.a. 7000 lm (*) Propulsion systems remains a tolerance of +/- 10% on luminous flux measurements @ 25°C ; 12VAC For operation only with a safety isolation transformer Minimum input voltage: (at lamp terminals) Nominal input voltage: (at lamp terminals) Maximum input voltage: (at lamp terminals) 10 VAC 50/60 Hz 12 VAC 50/60 Hz 14 VAC 50/60 Hz IEC Protection Class III Operation on DC voltages is NOT allowed Maximum water temperature: +40°C Lamps have to be kept out of ice zones Ingress protection rate: IP68 measured at 3m max depth = 3m 4 ENG Remarks Water conditions Prevent damage to your pool lamps and wires due to unstable water conditions. Your local government may have enacted guidelines for your pool water conditions to apply by. If not we strongly advise the following parameter specifications to be applied: pH level Free Chlorine Combined chlorine Water temperature 6,8 - 7,6 max. 3ppm max. 1 ppm max +40°C and lamps need to be kept out of ice zones Always adhere to the instructions provided by your chemical brand/supplier for the correct use and application of pool chemicals. Salt water pools, or pools fitted with a salt water chlorine generator contain salt in the pool water. Salt is a corrosive material. Overdosage and/or consistent levels of salt increase the possibility of deterioration of your pool lamps and cables. As a rule of thumb, a concentration of 35gr/l salt can be accepted when pH values are between 7,2-7,4. In any case, we urge proper use, care and maintenance of your installation, in order to minimize the effect of corrosion and deterioration. Please be aware that pool lamps and cables with defects caused due to abnormalities in the water condition are not covered by our factory warranty. 5 Installation/maintenance The luminaire is maintenance free If the luminaire needs to be replaced, it needs to be completely removed from the water If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively ! replaced by the manufacturer or his service agent or a similar qualified person in order to avoid hazard VISION Pro Pool lamps must be completely submerged into water during operation. ! Fixing the lamps with adhesives or silicone kit into a niche is not allowed Not following these instructions, will void warranty. 6 ENG Box contents VISION Pro lamp (50, 100 or 170 mm) Connection Kit* 2m Cable** Manual Retrofit Kit (only for 170mm models) * Lamp type ** DVP050-RGBW DVP100-RGBW DVP170-RGBW Connection kit 513-0480 ; 1 washer for fixnut ; blue cable gasket 513-0636 ; 2 washers for fixnut ; orange cable gasket 513-0393 ; 3 washers for fixnut; green cable gasket Cable 1 mm2 1,5 mm2 2,5 mm2 7 Installation instructions Installing faceplate Toolset ( not included ) Contact your local distributor for a toolset (513-0151) Lamp Face Plate 8 ENG Installation instructions Installing connector DVP050-RGBW 2m Cable DVP100-RGBW Washer Fix Nut Silicone Gasket Connector ! Installation: Page 10 & 11 DVP170-RGBW 9 Connector installation 1 2 3 10 ENG 4 5 6 11 Installation specialties DVP050 & PZA-WG For installations with DVP050 & PZA-WG-S or PZA-WG-G: Please make sure to only use 1 silicone washer for the Fix nut PZA-WG-G Fix nut 12 ENG DVP050 Removal tool When DVP050 needs to be removed from the PZA-WG wall conduits, a special tool is needed (513-0491)* 1. Insert the tool over the lamp, straight into the wall conduit 2. Twist the tool counter clockwise the lamp should be snapped into the 3 hooks of the tool 3. Pull the lamp straight out of the wall conduit * Available separately 13 Wiring instructions Setup 1 For new installations Each lamp is connected to the transformer by a separate cable Pool Pool house SELECT CABLE SECTION & MAXIMUM LENGTH 2m cable included in lamp package Separate cable ( not included ) ! Always use a toroïdal transformer 14 ENG LAMP TYPE SELECT CABLE SECTION & MAXIMUM LENGTH 1,5mm2 2,5mm2 4,0mm2 6,0mm2 10mm2 VA TRANSFORMER (12VAC)* DVP050-RGBW 23m 35m 60m 95m 155m 43 VA DVP100-RGBW 9m 15m 24m 35m 60m 111 VA DVP170-RGBW 4m 7m 11m 17m 29m 234 VA STABLE OPERATION OF THE POOL LIGHTS IS ONLY GUARANTEED WHEN THE INSTALLED CABLE CROSS SECTION MATCHES OR EXCEEDS THE ADVISED VALUES IN THE ABOVE TABLE * The transformer VA rating must be greater or equal to the sum of VA ratings of all connected lamps. These cable lenghts are calculated with worst case voltage drops in the electrical wiring. 15 Wiring instructions Setup 2 For existing or other installations All lamps are connected to the transformer via 1 cable Pool Pool house SELECT CABLE SECTION & MAXIMUM LENGTH 2m cable included in lamp package Separate cable ( not included ) ! Always use a toroïdal transformer 16 ENG LAMP TYPE DVP050-RGBW DVP100-RGBW DVP170-RGBW SELECT CABLE SECTION & MAXIMUM LENGTH QTY 2,5mm2 4,0mm2 6,0mm2 10mm2 VA TRANSFORMER (12VAC) 1 35m 60m 95m 155m 43 2 18m 30m 48m 78m 86 3 12m 20m 32m 52m 129 4 9m 10m 24m 39m 172 1 15m 24m 35m 60m 111 2 8m 12m 18m 30m 221 3 5m 8m 12m 20m 332 4 4m 6m 9m 15m 442 1 7m 11m 17m 29m 234 2 4m 6m 9m 15m 468 3 2m 4m 6m 10m 702 4 2m 3m 4m 7m 936 STABLE OPERATION OF THE POOL LIGHTS IS ONLY GUARANTEED WHEN THE INSTALLED CABLE CROSS SECTION MATCHES OR EXCEEDS THE ADVISED VALUES IN THE ABOVE TABLE 17 Wiring remarks For installations with LINK Controller or LINK Master Third party equipment such as frequency inverters and electric motors can generate excessive noise on the 230VAC / 400VAC power line. This noise might be injected into the adjacent 12VAC power line and disturb the power line communication towards the VISION Pro RGBW lights. To prevent this, please take care of the following: ! Keep 230VAC / 400VAC power line cables at least 50cm separated over their full length from the 12VAC power line towards any RGB lights ! Do not mix 12VAC and 230VAC / 400VAC power line cables into the same cable trays 18 ENG Pool Pool house 12VAC to lamps (**) 230VAC Min. 50cm 230VAC / 400VAC to third party equipment (**) Do not mix 12VAC and 230VAC / 400VAC power line cables into the same cable trays 19 Synchronizing With LinkTouch + LINK Controller (PLP-REM or PLP-REM-350)* + LINK Master (DLM450 or DLM600) First make sure the LinkTouch is paired (see manual LinkTouch) Turn the lamps on and spin the color wheel on the LinkTouch until the lamps react. If the lamps do not react, turn them off and back on untill they react to the color wheel. As soon as the lamps follow the color wheel: wait 1 minute. The lamps are now synced. With Transmitter + LINK Controller (PLP-REM or PLP-REM-350)* Turn the lamps on and push the UP button 10 times. Wait for 20 seconds, then turn the lamps off. Repeat this process until the lamps react to the remote. As soon as the lamps follow the remote: wait 1 minute. The lamps are now synced. Manual synchronization (without DURALINK control products) 1. Switch ON the 12 VAC line voltage and make sure that all lamps light up. 2. Switch OFF the 12 VAC line voltage and wait for at least 1 minute 3. Switch ON 4. The lamps should now all be on color program 1: Blue *PLP-REM or PLP-REM-350 need to have firmware V6.7 (29-07-20) or newer 20 ENG Color programs RGBW LAMPS 1 DEEP BLUE SEA Saturated blue 2 DAYLIGHT BLUE Light blue 3 SUNSET Slow animation orange - red 4 LOVE IS IN THE AIR 55 FOREST SPRING Red Green 6 THINK PINK 7 SUNSHINE 8 JUNGLE BEACH 9 VOODOO Pink Yellow Slow animation blue & green tints Slow animation red & purple tints 10 DISCO Fast animation lila-pink-peach-yellow-green blue 11 PARTY Fast animation blue-green-red-pink-yellow-green 12 WARM WHITE 3000K 13 NEUTRAL WHITE 14 SUN WHITE 6000K 10.500K fixed colors dynamic colors white tints *all color programs are dimmable if LINK Touch, LINK Controller or LINK Master are used (in PLC mode) 21 Troubleshooting PROBLEM . The pool light is flickering . Several pool lights in the pool show different color programs . The lamp is flashing red 22 SOLUTION 1. Switch the lamps ON and select Cold white color program 2. Remove the lamp from the water, unscrew the fix nut, pull back the gasket and the black cable jacket, so you can reach the brass contacts inside the connector block (do not remove the connector block) 3. Measure the voltage at the lamp terminals (while the lamp is still ON) 4. The voltage at the lamp should be at least 10VAC 50/60Hz. If the measured line voltage is below 10VAC: A. Check the output voltage at the transformator terminals. This voltage should be between 12VAC and 14VAC. Verify that the used transformator VA rating is sufficient for powering all connected lamps B. If the transformator output voltage is ok, then install a thicker cable between the transformator and the lamp. (wiring instructions p. 14-19) Make sure that all lamps are connected to the same 12VAC power line. Execute the synchronization as explained on p.20 The lamp is exposed to an overvoltage. Consult an electrician to verify the installation and to make sure the voltage at the lamp side is below 14VAC. ENG Declaraction of Conformity Declarations of conformity covering this product are available for download from the House of Duratech website: www.duratech.be VISION Moonlight VISION Spectra VISION Adagio Pro VISION Pro VISION Wall Conduits VISION Face Plates VISION Specials HEAT Hot Splash HEAT Sun Spring HEAT Dura V HEAT Dura Vi HEAT Dura +i HEAT Dura Pro HEAT Accessories FLOW Inverter FLOW Cartridge Filter COVER Tube COVER Motor COVER Wall Duct COVER Cable Duct COVER Hanging System LINK Driver LINK Touch LINK Controller LINK Cover LINK Master LINK Accessoires 23 Contact details Propulsion Systems bv Dooren 72 1785 Merchtem, Belgium Tel +32 2 461 02 53 www.duratech.be info@propulsionsystems.be We reserve the rights to change all or part of the contents of this document without prior notice 402-0259-6