User Manual for Shenzhen Hobk Electronic Technology models including: HBK-D01, HBKD01, 2A4H6HBK-D01, 2A4H6HBKD01, HBK-D01 RFID Card Reader, RFID Card Reader
SHENZHEN HOBK ElECTRONIC TECHNOLOGY CO., LTD HBK-D01 WIEGAND RFID READER 2A4H6HBK-D01 2A4H6HBKD01 hbk d01
RFID CARD READER USER MANUAL HBK-D01 1.Warm Tips 1Confirm the voltage (12VDC) and differentiate positive anode and cathode of the power supply. 2About the wiring between the reader and the controller, the wire should be 22 AWG at least and the length should not exceed 100 meters. 3When external power is used, suggest to use same power GND with controller panel. It is recommended to use multi-strand twisted pair cable to connect card reader to access controller. 4There is no need to wire the LED and BEEP cables if you do not need the card reader to prompt an authorized card through sound and light. 2.Introduction The RFID card reader can't work-alone and it needs to work with Wiegand protocol access controller, such as access control panel, fingerprint device or master controller. It uses ST MCU to ensure stable performance, and low-power circuit makes the service life longer. 3.Features The maximum reading distance is 6cm. Waterproof, conforms to IP66. It is useful for safety door system, easy to connect and use. Ultra-low power consumption, the standby current is less than 50mA. Support wiegand 26bits or wiegand 34bits output format. Fast response speed, the door opening time is less than 0.3s. Widely used in factories, houses, residential quarters, offices, mechanical and electrical control equipment and so on. 4. Specification Working Voltage 12VDC Static Current 50mA Card Type EM-ID Frequency 125KHz Working Temperature -40~60 Working Humidity 10%-90%RH Panel Material PC Waterproof Rating IP66 Shell Material PC + ABS Shell Size 90x45x19mm Wiegand 26bits Output Format (Selectable) Wiegand 34bits Communication Distance <100M Status Indication Bi-color LED + Buzzer Lead Cable Length 25cm LED Status Indication Red means standby, Green means activated/triggered 5. Wiring Definiti Color Functionality Description Red +12V +12V power input Black GND GND Green D0 Wiegand output D0 White D1 Wiegand output D1 Blue LED LED signal feedback Yellow BEEP Buzzer signal feedback Gray Wiegand 34bits Optional Note: If the output format of the card reader you want is Wiegand 34bits, please connect the Gray wire and the Black wire together. 6.Installation Remove the back cover from the reader Drill 2 holes on the wall for the self-tapping screws and 1 hole for the cable Put the supplied rubber plugs into the 2 holes Fix the back cover firmly on the wall with 2 self-tapping screws Thread the cable through the cable hole Attach the keypad to the back cover 7.Sound and Light Indication Operation Status LED Indicator Standby Red Read authorized card Green Read un-authorized card Flash red 3 times Buzzer A short beep 3 short beeps Remarks: The card reader will prompt sound and light indication only when the LED and BEEP cables are connected to the access controller. 8. Wiring Diagram 9.Packing List Name Card Reader User Manual Plastic Anchors Self-Tapping Screw Quantity 1 1 2 2 Remarks Used for fixing #7x1", used for fixing FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.Adobe Acrobat Pro DC 15.7.20033 Adobe Acrobat Pro DC 15.7.20033