Installation Guide for EcoFasten models including: Versatile Flashed Base Plate, Flashed Base Plate, Base Plate, Plate
EcoFasten EFS-2011013 from BayWa r.e.
VERSATILE FLASHED BASE PLATE INSTALLATION GUIDE REVISION: 0088//0022//2222 VERSION: VW2I.P3_V1.0 ECOFASTENSOLAR.COM TABLE OF CONTENTS QUIKFOOT INSTALLATION GUIDE REVISION: 08/02/22 VERSION: V2.3 CLICKING THE PAGE NAME WILL TAKE YOU TO THAT PAGE TABLE OF CONTENTS PAGE 01 FEATURES & BENEFITS PAGE 02 COMPONENTS PAGE 03 INSTALLATION PAGE 04 LINE DRAWINGS PAGE 06 SPECIFICATIONS PAGE 16 PAGE 01 QUIKFOOT INSTALLATION GUIDE REVISION: 08/02/22 VERSION: V2.3 FEATURES+ BENEFITS QUIK FOOT QuikFoot includes a base plate and uses two self-drilling attachment points for optimal pullout value. When paired with an EcoFasten compression bracket, the QuikFoot flashing creates a watertight seal that will maintain the roof's integrity. FEATURES · Patented Watertight Technology · Installs without removing shingles · Can be used on slate roofs · Two self-drilling screws provide optimal strength · Compatible with a variety of compression brackets PAGE 02 QUIKFOOT INSTALLATION GUIDE SYSTEM COMPONENTS 2 3 4 REVISION: 08/02/22 VERSION: V2.3 1 5 COMPONENTS 6 7 1. L-FOOT SCL-101 BLK 3" (OTHER OPTIONS AVAILABLE) 2. 5/16" SERRATED FLANGE NUT 3. 5/16" EPDM BONDED SEALING WASHER 4. EPDM SEALING WASHER 5. QF FLASHING AL BLK 8X12" 6. #15-13 SELF DRILLING FASTENER (2X) 7. QF BASE AL 1.25" PAGE 03 QUIKFOOT INSTALLATION GUIDE INSTALLING QUIKFOOT REVISION: 08/02/22 VERSION: V2.3 Snap horizontal chalk lines to mark the position of each row. Find the rafters and mark the position for installation. INSTALLATION Place the QF Base over the rafter vertically and screw down using two fasteners. The stud on the base plate should line up with the chalk line. Slide the flashing over the base plate and under the row of shingles directly above the base plate. (If the course of shingles is elevated by the flashings, notching of the shingles is acceptable) PAGE 04 QUIKFOOT INSTALLATION GUIDE INSTALLING QUIKFOOT REVISION: 08/02/22 VERSION: V2.3 Place the bare EPDM washer over the stud, pushing it all the way down. Then place an EcoFasten compression bracket over the stud and bare EPDM washer, followed by the bonded sealing washer with the rubber side facing down. Secure the bracket to the stud using the serrated flange nut and torque to 50-inch pounds. INSTALLATION PAGE 05 QUIKFOOT INSTALLATION GUIDE REVISION: 08/02/22 VERSION: V2.3 LINE DRAWINGS CUQTFSHBAEESTE:AQLF1B.2A5S"E AL 1.25" PART NUMBER 3012014 DESCRIPTION QF BASE AL 1.25" 2 3 1 ITEM NO. DESCRIPTION 1 QF BASE AL 1.25", ASSEMBLY 2 SS SERRATED FLANGE LOCK NUT, 3/8-16 3 3/8 STAINLESS STEEL AND EPDM BONDED SEALING WASHER 1) QF BASE AL 1.25", ASSEMBLY 3.25 1.5 2X 0.33 THRU ALL 1.34 1.02 3/8" THD Material Finish Aluminum/Steel Mill REV.- CS1 PAGE 06 QUIKFOOT INSTALLATION GUIDE REVISION: 08/02/22 VERSION: V2.3 CUT SHEET: QF BASE AL 1.25" LINE DRAWINGS PAGE 07 LINE DRAWINGS QUIKFOOT INSTALLATION GUIDE REVISION: 08/02/22 VERSION: V2.3 CUQTFSHFLEAESTH: QINFGFLAALSBHLIKN8GXA12L"BLK 8X12 PART NUMBER 3012016 DESCRIPTION QF FLASHING AL BLK 8X12" 1 2 ITEM NO. 1 2 DESCRIPTION QFL 8X12 MATTE BLK FLASHING EPDM SEALING WASHER 1) QFL 8X12 MATTE BLK FLASHING 8.0 12.0 0.47 THRU 0.51 Material Finish Aluminum Black REV.- CS1 PAGE 08 QUIKFOOT INSTALLATION GUIDE REVISION: 08/02/22 VERSION: V2.3 CUT SHEET: QF FLASHING AL BLK 8X12 LINE DRAWINGS PAGE 09 QUIKFOOT INSTALLATION GUIDE REVISION: 08/02/22 VERSION: V2.3 LINE DRAWINGS CUTL-SFHOEEOT: TL-FLO-O1T0L2-1B02LBKLK33"" PART NUMBER 3011015 DESCRIPTION L-FOOT L-102 BLK 3" 1 2 3 ITEM NO. DESCRIPTION 1 L-102-3 ANOD BLK 2 SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG 3 SS SERRATED FLANGE LOCK NUT, 3/8-16 1) L-102-3 ANOD BLK 1.88 0.38 THRU ALL 0.42 3.0 2X 0.41 2X 0.46 1.92 Material Finish Aluminum Black REV.- CS1 PAGE 010 QUIKFOOT INSTALLATION GUIDE REVISION: 08/02/22 VERSION: V2.3 LINE DRAWINGS CULT-SFHOEOETT: LL-F-O1O0T2L-M10L2 LML6L"6" PART NUMBER DESCRIPTION 3011016 L-FOOT L-102 MLL 6" 1 2 3 ITEM NO. 1 2 3 DESCRIPTION L-102-6 SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG SS SERRATED FLANGE LOCK NUT, 3/8-16 1) L-102-6 0.38 THRU ALL 2.0 2X 0.41 0.41 2X 1.6 6.0 3.02 Material Finish Aluminum Mill REV.- CS1 PAGE 11 QUIKFOOT INSTALLATION GUIDE REVISION: 08/02/22 VERSION: V2.3 CULT-SFHOEOETT: LS-FCOLO-T1S0C1L-1M01LMLLL33"" PART NUMBER 3011017 DESCRIPTION L-FOOT SCL-101 MLL 3" 1 LINE DRAWINGS 2 ITEM NO. 1 2 3 3 DESCRIPTION L FOOT W/ STANDARD DIMPLE AND OPEN SLOT, 3 IN TALL MLL SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG SS SERRATED FLANGE LOCK NUT, 3/8-16 1) L FOOT W/ STANDARD DIMPLE AND OPEN SLOT, 3 IN TALL MLL 0.38 THRU ALL 1.88 0.42 0.41 1.75 3.0 1.92 Material Finish Aluminum Mill REV.- CS1 PAGE 012 QUIKFOOT INSTALLATION GUIDE REVISION: 08/02/22 VERSION: V2.3 CULT-SFHOEOETT: LS-FCOLO-T1S0C1L-1B01LBKLK33"" PART NUMBER 3011018 DESCRIPTION L-FOOT SCL-101 BLK 3" 1 LINE DRAWINGS 2 3 ITEM NO. 1 2 3 DESCRIPTION L FOOT W/ STANDARD DIMPLE AND OPEN SLOT, 3 IN TALL BLK SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG SS SERRATED FLANGE LOCK NUT, 3/8-16 1) L FOOT W/ STANDARD DIMPLE AND OPEN SLOT, 3 IN TALL BLK 0.38 THRU ALL 1.88 0.42 0.41 1.75 3.0 1.92 Material Finish Aluminum Mill REV.- CS1 PAGE 13 QUIKFOOT INSTALLATION GUIDE REVISION: 08/02/22 VERSION: V2.3 CUTCSFHUEENT: CIVF ULN-IFVOL-OFOTOTMMLLLL 33"" PART NUMBER DESCRIPTION 2012022 CF UNIV L-FOOT MLL 3" 1 LINE DRAWINGS ITEM NO. 1 1) CLICKFIT L FOOT ASSEMBLY 0.79 THRU DESCRIPTION CLICKFIT L FOOT ASSEMBLY 1.79 3.06 2.76 0.38 THRU Material Finish Aluminum/Stainless Steel Mill REV.- CS1 PAGE 14 QUIKFOOT INSTALLATION GUIDE REVISION: 08/02/22 VERSION: V2.3 DECDKESCCKRSEW CRSESW SS PART NUMBER 3016010 3016011 3016012 DESCRIPTION DECK SCREW SS #15X2" DECK SCREW SS #15X3" DECK SCREW SS #15X4" 1 LENGTH (L) 2" 3" 4" LINE DRAWINGS ITEM NO. DESCRIPTION 1 ROOFING SCREW, DRILL POINT, BLACK 1) ROOFING SCREW, DRILL POINT, BLACK 0.44 1/4" THD 0.11 Material Finish L Steel Black REV.- CS1 PAGE 15 QUIKFOOT INSTALLATION GUIDE REVISION: 08/02/22 VERSION: V2.3 SPECIFICATIONS SYSTEM COMPONENTS 1. QF Base AL 1/25": Consists of (1) stainless steel base plate attachment bracket with (1) preinstalled stainless steel stud, (1) stainless steel serrated flange nut and (1) EPDM sealing washer. Base is made out of 6000 series aluminum. 2. QF FLASHING AL BLK 8X12": Black finish (Kynar painted) .032 gauge aluminum, embossed. 3. Fastener: Self-drilling #15 roofing screws are available from Ecofasten in 2", 3" and 4" lengths. Third party fasteners that have been approved by the engineer of record are permissible. 4. Recommended Sealant: If required by roof manufacturer, sealant shall be roof manufacturer approved. DELIVERY / STORAGE / HANDLING Inspect material upon delivery. Notify manufacturer within 24 hours of any missing or defective items. Keep material dry, covered and off the ground until installed. PATENTS Visit www.efpatents.com for patent information. PAGE 16 SPECIFICATIONS QUIKFOOT INSTALLATION GUIDE REVISION: 08/02/22 VERSION: V2.3 DESIGN REQUIREMENTS 1. Bracket spacing to be recommended by project engineer. 2. Install a minimum of two fasteners per base plate. 3. It is important to design new structures or assess existing structures to make sure they withstand retained loads. EXAMINATION 1. Substrate: Inspect structure on which brackets are to be installed and verify that it will withstand any additional loading that may be incurred. 2. Notify General Contractor of any deficiencies before installing EcoFasten Solar brackets. 3. Verify that roofing material has been installed correctly prior to installing solar attachment bracket. INSTALLATION Comply with architectural drawings and project engineer's recommendation for location of system. Comply with Manufacturer's written installation instructions for installation and layout. PAGE 17 4 1 4 1 W. V A N B U R E N S T, S U I T E 2, P H O E N I X A Z 8 5 0 0 9 1 - 8 7 7 - 8 5 9 - 3 9 4 7 | INFO@ECOFASTENSOLAR.COMAdobe PDF Library 16.0.7 Adobe InDesign 17.3 (Macintosh)