Instruction Manual for access LIGHTING models including: 52069LEDD, Anello Pendant Ceiling Light, Pendant Ceiling Light, Ceiling Light, Anello Light, 52069LEDD
Access Lighting 52069LEDD-MBL/ACR 641594242805 0641594242805 1008211627
Access 52069LEDD-MBL/ACR Anello LED 32 inch Matte Black Pendant Ceiling Light
File Info : application/pdf, 2 Pages, 271.43KB
DocumentDocumentCERTIFICATION: cULus DRY NO. 52069LEDD INSTALLATION INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS MESURES DE SECURITE A RESPECTURE Before assembling your ACCESS LIGHTING fixture, please make sure that you carefully read through this instruction sheet. Save this instruction sheet and refer to it when additions to or changes in the fixture configuration are made. Lisez attentivement ce manuel d'instructions. Enregistrer cette feuille d'instructions et de s'y référer lorsque les ajouts ou changements dans la configuration de montage sont faites. CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR. CONSULTER UN ELECTRICIEN QUALIFIE POUR VOUS ASSURER QUE LES CONDUCTEURS DE LA DERIVATION SONT ADEQUATS THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D'INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHERENTS NOTE: The important safeguards and instructions that appear in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution and care, are factors that can't be built into any product. These factors must be supplied by the person(s) caring for and operating the fixture. Read all instructions Do not install this fixture in hazardous locations. N'installez pas cet appareil dans des emplacements dangereux. Do not install any fixture assembly closer than 6 inches from any curtain or similar combustible material. Laisser une distance d'au moins 6 pouces entre ce luminaire et la toute surface combustible. "WARNING Risk of Fire and Electric Shock." "CAUTION: Risque d' Incendie et de Choc Electriques." GENERAL INFORMATION All electrical connections must be in accordance with all ordinances, Local and the U.S. National Electrical Codes (NEC). These fixtures are intended for mounting to a standard 4" metal octagon outlet box. The box must be directly supported by the building structure and U.L. Recognized. 1 COLLECTION ANELLO APPLICATION PENDANT MODEL NO. 52069LEDD WHAT WE PROVIDE · Mounting Hardware · Metal with Acrylic shade · LED WHAT YOU NEED · Screwdriver · Wire Cutters · Wiring Supplies as Specified by Electrical Code Recommended Dimmers (0-10V) Any 0-10V Dimmer (ELV) LUTRON Diva DVELV-300P (ELV) LUTRON Maestro CL MACL-153M (ELV) LUTRON Skylark Contour CTCL-153P (TRIAC) LEVITON Decora Sureslide 6672 (TRIAC) LEVITON Decora Sureslide 6674 (TRIAC) LUTRON Diva DVCL-153P (TRIAC) LUTRON Skylark CL SCL-153 or SCL-153P STEP BY STEP INSTRUCTIONS Before starting your installation disconnect the Power by turning off the Circuit Breaker or by removing the fuse at the fuse box. Just turning the light off at the light switch is not sufficient to prevent electrical shock. CERTIFICATION: cULus DRY N L NO. 52069LEDD 1 MOUNT THE MOUNTING BRACKET If there is an existing fixture remove it. Align the mounting bracket to the junction box and with a pencil, mark the location of the drywall anchors. Drill a hole and insert the supplied drywall anchors. Secure the mounting bracket to the junction box and drywall anchors with the supplied screws. 2 3 MAKE WIRE CONNECTION AND MOUNT THE CANOPY TO THE MOUNTING BRACKET Expose the supply wires from the J-box. Gently pull the supply wires through the hole in the mounting bracket. Connect the black supply wire to the black driver wire. Secure with the supplied wire nuts. Connect the white supply wire to the white driver wire. Secure with the supplied wire nuts. Attach the green J-Box wire around green hexagonal head screw or connect it to the green supply grounding wire of the fixture. Secure all wires with electrical tape (not supplied). Tuck all wires carefully into the J-Box. If not connecting to 0-10V dimmer, cap off the Grey and Purple wires with supplied wire nuts. Align the fixture canopy to the mounting bracket and secure with the supplied screws. RESTORE THE ELECTRICITY AND CHECK THE OPERATION OF YOUR NEW ACCESS LIGHTING FIXTURE If the fixture is to be removed or replaced, CAUTION please ensure that the electricity is switched off and that the fitting is cool before touching it. 2 VER: 21.10.1Adobe PDF library 9.90 Adobe Illustrator CS5.1