Instruction Manual for MONSTERTECH models including: 00670001, VPC Control Panel Mount, 00670001 VPC Control Panel Mount, Control Panel Mount, Panel Mount
MTSIM VPC CONTROL PANEL MOUNT INSTRUCTION MANUAL 13 M8x18 joint plastic washer Ø16 black locknut M8 A locknut has to be rough-running on a bolt. Therefore you need to use a wrench and a hex key
Manuals – MONSTERTECH USA
File Info : application/pdf, 15 Pages, 1.28MB
DocumentDocumentVPC CONTROL PANEL MOUNT Instruction Manual Bedienungsanleitung Mode d`emploi GENERAL ASSEMBLY INFO AND HOW TO PROFILE NUT HEX KEY SET WITH BALL HEAD + EXTENSION OR SIMILAR REQUIRED MTSIM VPC CONTROL PANEL MOUNT INSTRUCTION MANUAL 2 UNIVERSAL CONNECTOR M8x30 Ø8mm Nut M8 BOLT DIMENSIONS AND HOW TO MEASURE THEM [mm] 35 M8x35 25 M8x25 8 8 MTSIM VPC CONTROL PANEL MOUNT INSTRUCTION MANUAL 3 PROFILE CAP ASSEMBLY MTSIM VPC CONTROL PANEL MOUNT INSTRUCTION MANUAL 4 PARTS FOR TOP / FRONT MOUNT 1x 1x [dimensions in mm / different scales] 5 6 6 2x 22 2x 18 4x 16 PARTS FOR SIDE MOUNT 1x 160 65 2x M6 4x Ø5,5 15 1x 40 4 0 8 8 1x 18 1x 16 1x M8 40 40 1x locknut M8 selbstsichernd 2x 6,6 12 1x plastic 8,4 16 MTSIM VPC CONTROL PANEL MOUNT INSTRUCTION MANUAL 5 CENTER ASSEMBLY 2x M6x18 flat head hinge MTSIM VPC CONTROL PANEL MOUNT INSTRUCTION MANUAL 6 4x washer Ø15 4x M5x16 2x slot nut M6 MTSIM VPC CONTROL PANEL MOUNT INSTRUCTION MANUAL 7 2x M6x22 MTSIM VPC CONTROL PANEL MOUNT INSTRUCTION MANUAL 8 MTSIM VPC CONTROL PANEL MOUNT INSTRUCTION MANUAL 9 ALTERNATIVE ASSEMBLY ON FRONT 2x M6x22 MTSIM VPC CONTROL PANEL MOUNT INSTRUCTION MANUAL 10 MTSIM VPC CONTROL PANEL MOUNT INSTRUCTION MANUAL 11 ASSEMBLY FOR SIDE MOUNT Remove the feets and keep the bolts. 2x washer Ø12 plastic black MTSIM VPC CONTROL PANEL MOUNT INSTRUCTION MANUAL 12 joint M8x18 A locknut has to be rough-running on a bolt. Therefore you need to use a wrench and a hex key to tighten it. Hold up the M8x18 bolt with the hex key while tighten the locknut with the wrench (or reverse). Its perfect tighten if you still can angle your mounted device but it is tight enough not to move unintentional. plastic washer Ø16 black locknut M8 MTSIM VPC CONTROL PANEL MOUNT INSTRUCTION MANUAL 13 M8x16 slot nut M8 13-06-2022 WARNING NOTICES CAUTION! Do not clamp your fingers while attaching the table mount. CAUTION! Check before usage if all screws are tightened. CAUTION! Check before usage that the mounting plate is screwed on tight after making height adjustments. DANGER: Contains small parts not suitable for children under 3 years. Only suitable for children over 12 years and adults. All MONSTERTECH products are hand assembled and quality checked. The mount is designed for usage only with a computer controller (f.e. joystick or throttle). We exclude liability if the product is used for purposes other than intended. MONSTERTECH shall be liable for damage arising from causes other than the detriment to life, body and health only to the extent that such damage arises from wilful misconduct, gross negligence or the culpable violation of a fundamental contractual obligation on the part of MONSTERTECH or a vicarious agent (e.g. the delivery service) of MONSTERTECH. Any further liability for damages shall be excluded. If you have safety concerns or questions regarding assembly, contact us under info@mtsim.com or visit www.mtsim.com/en WARNHINWEISE VORSICHT! Klemmgefahr beim Befestigen der Tischhalterung. VORSICHT! Achten Sie darauf, dass vor Benutzung alle Schrauben immer fest angezogen sind. VORSICHT! Achten Sie darauf, dass die Befestigungsplatte nach der Höheneinstellung fest angezogen ist. GEFAHR: Nicht für Kinder unter 3 Jahren, Kleinteile - Verschluckungsgefahr! Nur für Kinder ab 12 Jahren und Erwachsene Alle Produkte der Firma MONSTERTECH sind handgefertigt und qualitätsgeprüft. Die Halterung ist nur zur Verwendung in Kombination mit einem PC Controller (z.B. Joystick oder Schubreglers) ausgelegt. Wir übernehmen keine Haftung für zweckentfremdete Benutzung. Für andere als durch Verletzung von Leben, Körper und Gesundheit entstehende Schäden haftet die MONSTERTECH lediglich, soweit diese auf vorsätzlichem oder grob fahrlässigem Handeln oder auf schuldhafter Verletzung einer wesentlichen Vertragspflicht durch MONSTERTECH oder eines Erfüllungsgehilfen (z. B. dem Zustelldienst) der MONSTERTECH beruhen. Eine darüber hinausgehende Haftung auf Schadensersatz ist ausgeschlossen. Bei Fragen zur Sicherheit oder Aufbau unserer Produkte, wenden Sie sich an info@mtsim.com oder besuchen unsere Website unter www.mtsim.com NOTICES D`AVERTISSEMENT ATTENTION! Risque de pincement des doigts lorsque vous attachez la fi xation à la table. ATTENTION! Vérifi ez que toutes les vises sont correctement serrées avant utilisation. ATTENTION! Après ajustement en hauteur de la plaque de montage, vérifi ez que les vises sont correctement serrées avant utilisation. DANGER: Contient des petites pièces susceptibles d`être avalées. Ne convient pas aux enfants de moins de 3 ans. Utilisation appropriée pour enfants à partir de 12 ans et adultes. Tous les produits MONSTERTECH sont fait main et on passés les contrôles de qualité. La fixation est conçue uniquement pour une utilisation avec un joystick ou une manette des gaz. Nous dégageons toute responsabilité pour toute utilisation autre que celle prévue. Pour les dommages engendrés autres que l'atteinte corporelle, à la vie et à la santé, MONSTERTECH n'est responsable que dans la mesure où ces dommages reposent sur un acte intentionnel, une faute lourde ou la violation fautive d'une obligation contractuelle essentielle par MONSTERTECH ou par des agents délégués par MONSTERTECH. Une responsabilité allant au-delà en dommages et intérêts est exclue. Si vous avez des questions concernant la sécurité ou l`assemblage, contactez-nous a info@mtsim.com ou visitez www.mtsim.com/fr/