Installation Guide for PlumbNation models including: HMAC-600A Ultra 3 Inlet Macerator Pump, HMAC-600A, Ultra 3 Inlet Macerator Pump, 3 Inlet Macerator Pump, Macerator Pump, Pump

Bathroom Macerator Installation Guide

Bathroom, Macerator, Installation, Guide

www.plumbnation.co.uk

Flo-Force Ultra 3 Inlet Macerator Pump Installation Guide (472KB)

Flo-Force Ultra Macerator Pump with High Grade Motor Casing - 3 Inlets - HMAC-600A


File Info : application/pdf, 4 Pages, 472.06KB

PDF preview unavailable. Download the PDF instead.

flo-force-ultra-3-inlet-macerator-pump-installation-guide
Installation Requirements
Electrics: The unit must be installed to comply with current UK electrical regulations, with a fused spur rated at 3 amps. We advise that this is done by a registered electrician.
This appliance must be earthed. If the supply cord is damaged, it must be replaced by a qualified person. The cable type is H05VV-F, 3G0.75mm2 VDE. The IP rating of this appliance is IP55.
Water: The unit is designed for a horizontal toilet outlet with the standard European 18cm to the outlet centre from the floor. All other inlets must be gravity fed into the unit. The outlet comes as standard with a 32mm connection however 22mm can be used with a reducer. If using bends in the connecting pipe work ensure they are smooth curves to avoid blockages.
Specification: Water temperature should be a minimum of 1°C it is important that the unit does not freeze, and a maximum of 40 °C. Maximum vertical discharge 9.5 m. Maximum horizontal discharge 60m.

plumbworld
Big brands, small prices. 600A Macerator
Inputs
The macerator can be used with multiple inputs, or just one. Blanking plates are provided to help you.
Installation
The electrical installation of this product must be done by qualified persons only.
This macerator is only for use with a toilet using a horizontal outlet. The toilet must also have a flushing tank or tap. Note: the horizontal outlet must be 18cm above floor level in accordance with EU standards.

Customer Care Helpline Telephone: 0333 202 5981 Email: orders@plumbnation.co.uk Discharge pipe length to the first elbow must be a minimum length of 0.5m.
Toilet Only Configuration
NOTE DIRECTION OF

Discharge pipe mustbe32mm or40nmonly

Secure macerator to pan with large Jubilee clip, ensuring h Is fully tightened

 Place this horizontal toilet outlet into the macerator, and clamp the rubber sleeve of the macerator around the pipe using the supplied jubilee clip.
 Repeat for the 32mm or 40mm discharge pipe.

plumbworld
Big brands, small prices.

plumbworld
Big brands, small prices.
600A Macerator

Configuration with Other Appliances

Prior to first use flush a large quantity of clean water through the unit.
General Care and Maintenance

~ Dischafge Pipe

Util'ily S ink, Dislhwa;sher, ~ Waslhing1IMachiru:

Toilet

i;;;;:, Balh ,S!hO'l!Ver, Balhroom 13.asin

Connect the discharge pipes of each appliance to the rubber connectors provided and clamp with supplied jubilee clamps.
For use with a bath or shower, there must be a gradient of 1cm per metre or greater. If used with a shower, a second check valve must be used. This must be fitted between the macerator and the tray. If other appliances are fitted along the discharge line, check valves must also be used on these.

Daily Usage:
 This product is suitable for indoor use only.
 Do not put foreign objects, such as but not limited to condoms, sanitary towels, and wet wipes through the system as this will cause damage to the unit, and will invalidate your warranty.
Servicing:
· Service and cleaning should be performed once every 6 months. It is recommended that this is done by a professional.
· Before servicing, ensure the electric supply is off.
· Appropriate PPE must be used whilst servicing the unit.

Warranty
Please note the following situations that will invalidate the warranty:

 Failure to install the appliance in accordance with this installation guide.
 Installation by unqualified persons.  Foreign objects in the system.  Failure to carry out regular
servicing/maintenance as detailed in this guide.
Product Disposal This product should not be disposed of with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, the unit should be disposed of at an appropriate local authority facility.

The symbol on the appliance states

·

that it meets the new directive (2012/19/EU) and must be handled in

accordance with this standard at the

end of its service life.

plumbworld
Big brands, small prices.

plumbworld
Big brands, small prices.
600A Macerator

Trouble Shooting

Symptom The macerator has cut out
The macerator has cut out The water is back flowing The unit is leaking.
The macerator is nonoperational and has never been
opened.
The macerator is not powerful enough.
The macerator emits a humming noise but does not
discharge waste.
The macerator discharges waste with no demand.
Macerator is not emitting a humming noise.

Cause The device has overheated.
Power supply has been interrupted Insufficient gradient
Check valve/jubilee clips are not fitted correctly. The macerator is connected to an incorrect size pipe. The electrical install was incorrect. The check valve is facing in the wrong direction. Pressure switch is blocked
Discharge pipes are too long/high Discharge pipe is to small Unit is blocked.
Pump is blocked Check valve is installed the wrong way round. Check valve is faulty
The tank is leaking There is a partial blockage Pressure switch is defective The unit is not properly connected to the electric supply The pressure switch is not connected. The motor is not operational

Resolution Leave the unit to cool for 30 mins, switch it back on and hold the override switch to reset the unit. Check for blockages. Check fuses and power supply.
Ensure a gradient of 1cm per meter is used. Check these items.
Ensure the pipe is 32 or 40mm.
Ensure the device was installed by a qualified person. Check the check valve(s).
Check/replace the pressure switch. Check the distances against the spec. Check the sizes Service as per instructions above. Check/service pump. Check the check valve.
Examine/replace the check valve. Check the tank. Clear the blockage Replace the pressure switch Check the supply
Check by pressing the override switch several times. If pressing the override switch has no effect the motor may be dead.

plumbworld
Big brands, small prices.

Check out our full range of macerators.



References

Adobe Acrobat Pro DC 17 Paper Capture Plug-in; modified using iTextSharp 4.1.6 by 1T3XT