audio.com - a better way to upload and share audio online
Instruction Manual for PAC models including: PAC APH-CH03 AmpPro Harness 2015-20 select Chrysler Amplified Models, PAC APH-CH03, AmpPro Harness 2015-20 select Chrysler Amplified Models, Chrysler Amplified Models
PAC APH-CH03 AmpPro Harness Works with PAC's AP4-CH41 AmpPro module to install a new amplifier in select 2015-20 Chrysler, Dodge, Jeep, and RAM vehicles with factory amp at Crutchfield
File Info : application/pdf, 2 Pages, 437.70KB
DocumentDocumentAPH-CH03 Speaker connection harness for select Alfa Romeo, Chrysler, Dodge, Jeep, Maserati and Ram vehicles with factory amplified sound systems Introduction and Features The APH-CH03 simplifies speaker wire connections when adding aftermarket amplifiers. Aftermarket amplifiers can be easily added with no need to cut or modify a vehicle's original wiring. This harness has an additional feature of deactivating the active noise cancellation (ANC) system in applicable vehicles that are equipped with it. Each pair of speaker wires has been labeled with a number to help with tracking what vehicle speaker corresponds to it. Installation Notes 1. All connectors should be plugged in when using this wiring harness in order for the ANC deactivation feature to work properly. 2. Not all applicable vehicles will come equipped with a corresponding speaker for all of the wires populated in our harness. It is important to understand which speakers the vehicle is equipped with. 3. The positive polarity speaker wires on the APH-CH03 are indicated by a solid color. 4. The negative polarity speaker wires on the APH-CH03 are indicated by a stripe running along the length of the wire. 5. If you are leaving any of the factory speakers connected to the factory amplifier, simply connect the speaker wires (color for color) between the male and female connectors. For example, If you want speakers 3 and 4 to be powered by the factory amplifier, simply connect the Yellow and Yellow / Black, Green and Green / Black wires from the male connector to the Yellow and Yellow / Black, Green and Green / Black wires from the female connector. Installation Steps 1. Locate the vehicles factory amplifier and disconnect the White 22-pin, Gray 22-pin and Gray 10-pin connectors. 2. Connect the APH-CH03 harness to the connectors that were disconnected in the previous step. 3. Connect the male connectors from the APH-CH03 to the amplifier. 4. Use a tone generator (PAC Part# TL-PTG2) to verify what speakers in the vehicle correspond to the speaker numbers on the harness. 5. Use the wiring chart in this manual to write down what speaker in the vehicle corresponds to the speaker numbers labeled on the APH-CH03. For example, after testing with a tone generator you found that the Red and Red/Black wires labeled Speaker 1 correspond with the Front Left Tweeter in the Vehicle; you then write down Front Left Tweeter in the Speaker Description box for Speaker 1. 6. Connect the longer loose wires from the APH-CH03 to your aftermarket amplifier or passive crossovers according to the tables in this manual that were filled out in the previous step. Wiring Chart Wire Color Red Red / Black Orange Orange / Black Yellow Yellow / Black Green Green / Black Blue Blue / Black Purple Purple / Black Pink Pink / Black Light Green Light Green / Black White White / Black Gray Gray / Black Brown Brown / Black Black Black / White Polarity + + + + + + + + + + + + - Label Text Speaker 1 Speaker 2 Speaker 3 Speaker 4 Speaker 5 Speaker 6 Speaker 7 Speaker 8 Speaker 9 Speaker 10 Speaker 11 Speaker 12 Speaker Description P ifi A C ti Copyright © 2020. All rights reserved. PAC is a Power Brand of AAMP Global. PAC-audio.com Rev: v.1 Date:42220 Page 1 APH-CH03 Wiring Overview Speaker connection harness for select Alfa Romeo, Chrysler, Dodge, Jeep, Maserati and Ram vehicles with factory amplified sound systems Harnesses A and B (Gray 10-pin Connectors): Connect to aftermarket amplifier or passive crossover. OE Amplifier Outputs: Connect corresponding colored wires for any speakers you wish to remain OE amplified. Harness C (White 22-pin Connectors): OE Amplifier Outputs: Connect corresponding colored wires for any speakers you wish to remain OE amplified. Harness D (Gray 22-pin Connectors): Connect to aftermarket amplifier or passive crossover. Technical Support P ifi A C ti Email: support@PAC-audio.com Phone: 866-931-8021 International: 727-592-5991 Copyright © 2020. All rights reserved. PAC is a Power Brand of AAMP Global. PAC-audio.com Rev: v.1 Date:42220 Page 2