SECO-LARM SK-910RAQ Enforcer Rf Receivers Instruction Manual

Instruction Manual for SECO-LARM models including: SK-910RAQ Enforcer Rf Receivers, SK-910RAQ, Enforcer Rf Receivers, Rf Receivers

SECO-LARM SLI ENFORCER SK-910RAV-4Q (01) PDF MANUAL - Manual-Hub.com

File Info : application/pdf, 4 Pages, 790.99KB

SECO-LARM SLI ENFORCER SK-910RAV-4Q (01)

Installation Manual
ENFORCER ®

SK-910RAQ SERIES Miniature RF Receivers

Up to 500 ft. range

Operate on 11-24VAC/DC1

SK-910RAQ Shown

Code learning

FCC compliant

Fixed code or CODEBUMPTM code-hopping

Introduction

These mini RF receivers are compatible with both code hopping and fixed-code transmitters (see page 4 of this manual for a list of compatible transmitters). They can be used for a variety of applications, such as allowing the same transmitter to arm/disarm a vehicle alarm and open/close a garage door opener. The receivers come in one- or two-channel versions. Each channel can learn the codes of up to 15 different transmitter buttons on a first-in, first-out basis.
Installation Notes
1. Mount out of sight in a location where it is not surrounded by metal, and where it is not exposed to the weather or moisture. Metal will block the RF signal, resulting in a reduced range.
2. For best range, pull the antenna wire as straight and high as possible. If the receiver receives interference from local RF activity (eg., airport or military base), the antenna wire can be folded. DO NOT CUT THE ANTENNA WIRE.

Models Available
SK-910RAQ .......... 1-channel mini-receiver, 3A Form "C" relay, 315MHz SK-910RAVQ ........ 1-channel mini-receiver, 5A transistor ground output, 315MHz SK-910RAV2Q ...... 2-channel mini-receiver, 3A transistor ground outputs, 315MHz SK-910RA-4Q ....... 1-channel mini-receiver, 3A Form "C" relay, 433.92MHz SK-910RAV-4Q ..... 1-channel mini-receiver, 5A transistor ground output, 433.92MHz SK-910RAV2-4Q .. 2-channel mini-receiver, 3A transistor ground outputs, 433.92MHz More RF receivers are available (1 to 4 channels). Contact SECO-LARM for details.
1All models work on 11-24VAC/DC, except for the low voltage versions.

https://manual-hub.com/

ENFORCER RF RECEIVERS

Learning a New Button Code (channel 1)
1. Press the mode switch which is located at the top of the receiver case for three seconds. The green LED will start to flash quickly.
2. While the green LED is flashing quickly, press a button on a compatible transmitter. The green LED will flash once and then turn off to show that button was learned.
3. Repeat steps 1 and 2 to learn more buttons into channel 1.
NOTE -- The green LED will flash a maximum of 15 seconds. If no transmitter button is pressed during this time, the receiver will exit the code-learning mode, and the green LED will turn off.
Learning a New Button Code (channel 2, SK-910RAV2Q only)
The procedure is the same as for channel 1, except mode switch #2 (black switch) initiates the code-learning process, and the red LED shows status. For two channel receivers, red color push-button represent mode switch #1 and black color push-button represent mode switch #2 .
Note Regarding Code Learning
1. The receiver will only learn the code of a particular button once. Once a button's code is learned, if you try to codelearn that button again, whether it is for the same channel or not, the receiver will remain in the code learning mode. The LED will turn steady ON (1-sec.) to show the code is already in memory.
2. Each channel can learn the codes of a maximum of 15 transmitter buttons. If you attempt to learn a sixteenth button, the earliest code learned will be deleted and replaced by the new code (first-in, first out).
3. To clear all codes -- To clear all codes in the channel's memory, press the appropriate mode switch (#1 or #2) for three seconds. When the LED starts flashing, press that switch again for three seconds. The LED flashes twice to indicate that all codes associated with that channel are now deleted.
Programming Output Modes (see table 1)

4-second momentary
1-second momentary Toggle
Validity

Press the transmitter button once. The output turns on for 4 seconds, and then turns off. (This is the DEFAULT mode)
Press the transmitter button once. The output turns on for 1 second, and then turns off.
Press the transmitter button once, and the output turns on. Press a compatible transmitter button again, and the output turns off.
The relay turns on for as long as the transmitter button is pressed.

Mode Switch Operation (one per channel)

Learn mode

Press and hold the switch for three seconds. The appropriate LED will flash quickly to show that it is ready to learn a transmitter code.

Clear memory

Press three seconds, then when the appropriate LED starts flashing, press again for three seconds to delete all previously learned codes. The LED will flash twice to confirm codes deleted.

Memory Display

Press and immediately release the mode switch to show number of codes stored. The appropriate LED will flash a number of times to correspond to the number of codes stored.

LED Indication (one per channel)

Steady on Fast flash One flash Two flashes

Senses signal from a transmitter button whose code was already learned. In the code-learning mode. A transmitter button code was learned. All previously learned transmitter button codes were deleted.

https://manual-hub.com/

Page 2

ENFORCER RF RECEIVERS

SK-910RAQ

SK-910RAVQ/RAV2Q

Loop 3
Mode switch #1
Ext. range antenna connector Loop 2 Loop 1 Loop 4
Channel 1 Status LED
Channel 2 Status LED (SK-910RAV2Q only)
11~24 VAC/VDC No polarity COM NO NC

Mode switch #2 (SK-910RAV2Q only) Mode switch #1
3~13.8 VDC GND Ch 1 transistor ground Ch 2 transistor ground (SK-910RAV2Q only)

{

Table 1: To program outputs, open case and find the jumpers marked LP1, LP2, LP3, and LP4 . Cut these jumpers, if needed, as follows:

4-SEC.

1-SEC.

MOMENTARY MOMENTARY

TOGGLE

VALIDITY

LP1 UNCUT

UNCUT

CUT

LP2 UNCUT

CUT

UNCUT

CUT

LP3

CUT LP3 TO USE EXTERNAL ANTENNA

LP4 CUT LP4 FOR 16~24VAC/DC POWER INPUT (for SK-910RAQ only)

Typical Applications:

NOTE -- For the SK-910RAV2Q 2-channel model, the mode of both outputs is the same. In other words, you cannot have 4-second momentary output for channel 1 and a validity output for channel 2.

Positive or negative output:

12VDC receiver power driving a 12VDC appliance

NC NO COM +

Positive or Negative Power Output (Choose NO or NC)
Positive or Negative Power Source
} Power for SK-910RAQ / SK-910RA-4Q

12VDC receiver power input, 24VAC output driving a motor

NC NO COM +

(- )

(+)
12VDC O/P Electromagnetic lock

} GND
+12VDC

Power for SK-910RAQ / SK-910RA-4Q

For SK-910RAVQ /SK-910RAV-4Q and SK-910RAV2Q / SK-910RAV2-4Q

NC NO COM +

24VAC(1) Output Motor 24VAC(2)
24VAC(1) Input GND +12VDC

CH 2 Output**

CH 1 Output*
+

GND

DEVICE DEVICE

+3~13.8VDC

* For SK-910RAVQ / SK-910RAV-4Q ** For SK-910RAV2Q / SK-910RAV2-4Q

Extended Range Antenna for SK-910RAQ only The optional SK-91ERSD extends the RF receiver range to up to 1,200' (open air) with existing remotes.

The antenna comes with a 9' cable which easily plugs into the 3-pin antenna port located on the RF receiver motherboard

(see the illustration above).

IMPORTANT: If an extended range antenna is used with the

SK-91ERSD

SK-910RAQ, the receiver PC board loop marked "LP3" must be cut.

Page 3

https://manual-hub.com/

ENFORCER RF RECEIVERS

Specifications:

Range Operating Voltage Memory Capacity Current Draw

SK-910RAQ
Up to 500' range 11-24 V AC/DC (16~24 VAC/DC must cut LP4)
15 transmitter button codes per channel 5mA standby, 50mA LED flashing @ 12VDC

SK-910RAVQ SK-910RAV2Q
Up to 500' range 3-13.8 VDC
5mA standby, 15mA LED flashing @ 12VDC

Output mode Output type Dimensions Frequency Transmitter

Programmable 4-sec. momentary (default), 1-sec. momentary, toggle (ON/OFF), or validity

3A Form `C' relay (NO/NC/C).

Transistor GND x 1, 5A @ 12VDC Transistor GND x 2, 3A @ 12VDC

33/16" x 29/16" x 3/4" (80 x 65 x 19 mm)

315MHz. (Other frequencies available. Please contact SECO-LARM.)

Compatible with all SECO-LARM transmitters

Compatible Transmitters
Fixed-Code: 68 billion codes. CODEBUMPTM code-hopping: 18 quintillion (1.8 x 1019) codes
Pendant Remotes

Model Number
SK-919TD1S-U SK-919TD1S-UP SK-919TD2A-U SK-919TD2A-UP SK-917T2A SK-919TP3J-N SK-917T3J SK-919TP4J-N SK-917TP4J-N Hand-Held Remotes
Model Number
SK-919TP1H-B SK-919TP2H-N SK-919TP4H-N Accessories SK-9HBC

# of Buttons
1
2
3 4

# of Channels
1
3
7 15

Coding
Fixed Fixed Fixed Fixed Code Hopping Fixed Code Hopping Fixed Code Hopping

Blank or Pre-coded
Blank Pre-coded
Blank Pre-coded Pre-coded Pre-coded Pre-coded Pre-coded Pre-coded

# of Buttons
1 2 4

# of Channels
1 3 15

Coding
Fixed Fixed Fixed

Blank or Pre-coded
Pre-coded Pre-coded Pre-coded

Belt clip holster for hand-held remotes

CODEBUMPTM
With SECO-LARM's CODEBUMP, so-called codegrabbers and scanners are rendered obsolete because the RF code changes every time the transmitter button is pressed. In addition, with over 18 quintillion (1.8 x 1019) codes, the chances of ever repeating a code are virtually non-existent.
SECO-LARM's CODEBUMP transmitters and receivers are perfect for controlling garage and gate openers, car and home alarms, plus much more.

WARRANTY: These ENFORCER RF receivers are warranted against defects in material and workmanship while used in normal service for a period of one (1) year from the date of sale to the original customer. Our obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation pre-paid, to SECO-LARM.

Copyright © 2016 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM.
The SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without further notice.

SECO-LARM® U.S.A., Inc. 16842 Millikan Avenue, Irvine, CA 92606 Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326

FILE: MI_SK-910RAxxQ_151218.pmd

Order Part #762-107-5%

® PITSW1

Website: www.seco-larm.com E-mail: sales@seco-larm.com

Page 4

https://manual-hub.com/

References