1. Product Introduction
This product belongs to special effects equipment, intended for professional use. It functions as a fire simulator and is widely used in concerts, sports events, and theme activities to enhance events.
1.1 Product Overview
The SF-90 features a Firing Head, Fuel Bottle Area, Top Panel, Control Panel, Oil Scale, and Safety Loop.
1.2 Product Accessories
- 1.6 Meter Power Plug
- 3 Meters Power Pair Cable
- 3 Meters DMX Pair Cable
- Built-in Tank
- User Manual
ℹ️ NOTICE: Open the package carefully and check to make sure the goods are in good condition.
1.3 Fuel Allowed
Lsopropanol, Lsoparaffin, Bioethanol
1.4 Functional Characteristics
- Direct shooting of liquid fuel, with a maximum height of 8-10 meters.
- Compact pumping system ensures a compact machine size.
- Strengthened and rustproof metal panel with a water-proof design.
- 5L Built-in fuel tank without external pipeline.
- Double electromagnetic valves design for enhanced safety.
- Unique safety lock design for easy testing and prevention of spurious triggering.
- Tilt protection: the tilt sensor activates when the machine slants over 45°.
- Safe and reliable intelligent electronic control system with an alarm function.
- Standard DMX signal control compatible with any DMX console.
- Fitted with a fireworks ignition signal port, triggerable by fireworks ignition.
- Supports Chinese & English menu switching for easier operation.
2. Technical Parameters
| Identification | Manufacturer | SPARK FABRICA |
| Name | I FLAMER | |
| Model | SF-90 | |
| AC Power | Input Voltage & Frequency | 100-120V, 50/60HZ 200-240V, 50/60HZ |
| Work Power | 300W | |
| Power Input Connector | SEETRONIC | |
| Power Output Connector | SEETRONIC | |
| DMX Signal Interface | 5PIN | |
| Interface Type | Signal Interface | Double DMX Interface |
| Signal Interface | 9V-60V Fireworks Ignition Signal Interface | |
| Waterproof | IP Rate | IP55 (Waterproof Design) |
| Hopper | Fuel Bottle Capacity | 5L |
| Removable Hopper | N/A | |
| Control | Control Protocol | DMX-512 |
| Control Mode | Standard DMX Signal Control | |
| Effect Angles | vertical | |
| SMPTE | Touch Screen Console Support | |
| Accessory | Power Plug | SEETRONIC (1.6Meter) |
| Remote Controller | Optional | |
| DMX Cable | ✔️ 3Meter | |
| Power Cable | ✔️ 3Meter | |
| Safety Loop | ✔️ | |
| Update Box | Optional | |
| Oil Consumption | Firing Head L (Standard Configuration) | 30ml/s |
| Firing Head M (Standard Configuration) | 60ml/s | |
| Ignition | Ignition Mode | High Voltage Electronic Ignition |
| Weight | Net Weight (No Fuel) | 14kg |
| Gross Weight | 22kg | |
| Dimensions | Machine Dimensions - L*W*H | 330mm*260mm*345mm |
| Packing Dimensions - L*W*H | 730mm*587mm*725mm | |
| Fuel Oil | Kind | ISOPROPANOL, ISOPAR G,H,L,M |
3. Back Panel Guide
3.1 Back Panel Introduction
The back panel features the following controls and connectors:
- Power: Main power switch.
- MENU: Button to navigate menus and settings.
- 5 PIN DMX/CAN IN: 5-pin DMX/CAN data communication interface.
- 5 PIN DMX/CAN OUT: 5-pin DMX/CAN data communication interface.
- 3 PIN DMX/CAN OUT: 3-pin DMX/CAN data communication interface.
- 3 PIN DMX/CAN IN: 3-pin DMX/CAN data communication interface.
- Fuse: Fuse holder.
- 12V-24V Ignition Signal Port: For external ignition signals.
- BAT: Battery connection terminal.
- Safety Loop: Safety tether point.
- LCD Screen: Displays device status and settings.
- Safety Lock: Safety lock mechanism.
- Save Parameter: Button to save settings.
- - Decrease Parameter: Button to decrease values.
- + Increase Parameter: Button to increase values.
- INPUT AC 100V-240V: Power input ports (110V-240V).
4. Interface
4.1 LED Display Area
The LED display shows various parameters and statuses. Buttons include MENU, -, +, and ENTER. Indicators include RX (radio receiving), DMX (DMX signal status), ERR (error indicator), and PUMP (pump running indicator).
Welcome Interface: Displays Product Model (SF-90) and Software Version on the first line, and Equipment Series Number on the second line (e.g., SF-XXXXXX).
Main Interface: Shows DMX Address (e.g., DMX Address: 1) and Pressure/Voltage (e.g., P:100 V:15.6).
4.4 Alert Message
| Alert Message | Explanation |
|---|---|
| Test Mode | Safety lock located at TEST MODE. |
| Factory Mode | DMX signal blocked in factory mode. |
| E0 Invert ON | When turned on, all angles will be mirrored. |
| E1 Pressure Err | Pressurize for about 13s, pressure value failed to reach 100%. Possible faults: no fuel, pump failure, pipeline problem, etc. |
| E2 P Relief Err | Pipeline cannot release pressure, leading to pressure relief error. Possible faults: pressure release valve failure, pipeline problem, or control system problem. |
| E3 Motor Err | Possible fault: swiveling nozzle stuck, motor failure, etc. |
| E4 ExtIgnition ON | When Ext Ignite is ON, the device will pressurize automatically when the safety lock is switched to USER MODE; decompression when switched to TEST MODE. 9V-60V fireworks ignition signal will trigger related firing sequences. |
| E5 Voltage Err | Battery voltage >15V or <10V for continuous 5s; machine stops running. Possible fault: the battery is low. |
| E6 Tip Err | If the machine slants over 45°, it stops running and the system will report E6. |
4.5 Interface Setup
Press MENU to enter the setting interface. Press MENU again to cycle through options and return to the main interface.
| Menu | Range | Explanation |
|---|---|---|
| Set DMX Address | 1~512 | DMX address setup. |
| Set Wireless Switch | ON / OFF | Turn on/off Wireless Function. |
| Switch Transmit Receive | Mainframe/Slave | Switch mainframe/slave; default is slave. |
| Set The Wireless Address A | 1-255 | Wireless ID1, Anti-Interference. |
| Set The Wireless Address B | 2-255 | Wireless ID2, Anti-Interference. |
| Set Up Wireless Channel | 1-16 | Emit 1-16 packets of data, each packet is 32 bytes. |
4.6 Advanced Interface
Press and hold "MENU" for 3 seconds to enter the advanced interface. Press "MENU" to switch interfaces. Press and hold "MENU" for 3 seconds again to return to the main interface.
| Items | Contents | Description |
|---|---|---|
| Drive Test | 1. Pump | Swiveling and stop at target angle. |
| 2. Ignite | Swiveling and stop at target angle. | |
| 3. Relief Valve | Relief valve works for 3 times. | |
| 4. Jet Valve 1 | Safety lock must be user mode, release pressure for 5s, jet valve will work for 3 times. | |
| 5. Jet Valve 1 | Trigger through 9-60V fireworks ignite signal. | |
| Ext Ignite | OFF / ON | Trigger through 9-60V fireworks ignite signal. |
| Set Ext Ignite Time | 0.8-8s | Shooting time after triggered by fireworks ignite. |
| Language | English/Chinese | Language switch. |
| Mode Select | Normal Mode / Factory Mode | Factory mode is for test in factory only. |
| Tilt Switch | OFF / ON | Turn on tilt switch (Tilt over 45 degrees will stop shooting.) |
| Select DMX Channel | 2 Channel/ 6 Channel | Can work with Spark Fabrica other flame machines. |
| Restore default Settings | OFF / ON | Restore device default parameter settings. |
5. Operation Guide
5.1 Fast Operation Guide
After receiving the product, unpack and confirm its condition. Due to the inherent risks of flame machines, follow these operation procedures carefully to ensure safety.
- Installation: The device must be placed horizontally. If mounted on a truss, secure it with extra safety ropes.
- Safety Lock: Locate the safety lock at TEST MODE.
- Fueling: Fuel the machine with high-quality fuel as specified in this manual.
- Power and DMX Cable Connection: Connect the power supply (110V/220V mains or 12V battery) and DMX cable.
- Turn on Power: Ensure the safety lock is in TEST MODE before switching the power ON/OFF.
- Set DMX Address: Set the DMX address. The I FLAMER typically occupies 6 channels.
- Pressure: Activate the "HEAT" function on the host controller. On the DMX console, set DMX value of channel 6 to 50-200.
- Check Device Status in TEST MODE: Confirm the safety lock is in TEST MODE. The nozzle should rotate, and the igniter should activate, but no flame should be produced.
- Pressure Relief: Perform pressure relief if necessary.
- Switch Safety Lock to USER MODE: Before switching to USER MODE, ensure strict adherence to safety distance requirements and clear the danger area of people, animals, and flammable objects.
- Pressuriser: Activate the "HEAT" function on the host controller. On the DMX console, set DMX value of channel 6 to 50-200.
- Firing: Activate the "FIRING" function on the host controller. On the DMX console, set DMX value of channel 3 to 254-255.
- Pressure Relief: Relieve pressure when the show is finished or if the machine will not be used for an extended period.
- Switch Safety Lock to TEST MODE: Switch the safety lock back to TEST MODE to ensure safety for the next use.
- Power Off: Turn off the I FLAMER, disconnect the power and DMX cables, and pack the device once it has cooled down.
5.2 DMX Control (6 Channel, Default)
| Channel | Function |
|---|---|
| Channel 1 (CH1) | N/A |
| Channel 2 (CH2) | N/A |
| Channel 3 (CH3) | Ignite Switch: (0~253) no shooting; (254~255) start shooting. |
| Channel 4 (CH4) | Set Ignite Time: (0 and 255) shooting timelessly, 10s is the longest. (1 ~ 254) 10-2540ms, manual ignition time = DMX value * 10ms. |
| Channel 5 (CH5) | N/A |
| Channel 6 (CH6) | Mode setting: (0~49) Pressure Relief Mode (Emergency stop sequence); (50~200) Normal Shooting Mode; (201~255) Pressure Relief Mode (Emergency stop sequence). |
5.3 DMX Control (2 Channel)
| Channel | Function |
|---|---|
| Channel 1 (CH1) | Ignite Switch: (0~15) no shooting; (16~255) start shooting. |
| Channel 2 (CH2) | Mode setting: (0~239) Pressure Relief Mode (Emergency stop sequence); (240~255) Normal Shooting Mode. |
DMX Address Mapping (6 Channel Mode):
| I FLAMER Sequence | DMX Channel |
|---|---|
| 1 | 1 |
| 2 | 7 |
| 3 | 13 |
| 4 | 19 |
| 5 | 25 |
| 6 | 31 |
| 7 | 37 |
| 8 | 43 |
| 9 | 49 |
| 10 | 55 |
| 11 | 61 |
| 12 | 67 |
| 13 | 73 |
| 14 | 79 |
| 15 | 85 |
| 16 | 91 |
| 17 | 97 |
| 18 | 103 |
⚠️ CAUTION: Setting the wrong DMX address may cause the machine to lose control.
6. Machine Maintenance
Regular maintenance ensures optimal performance and longevity.
- It is recommended to operate the equipment at least once a month to maintain its best performance and status.
- Firing Head Maintenance: The nozzle should be removed for cleaning internal impurities. This should be done approximately every six months, depending on usage environment and frequency. If the machine casing or oil shooting line shows significant deformation or thickening, the firing head should be removed immediately for cleaning.
- O-ring Maintenance: If the O-ring of the nozzle is found to be damaged or aged during cleaning, it should be replaced promptly. The recommended O-ring material is fluoridated rubber, with an outermost diameter of 14 mm and a line diameter of 2 mm.
- Lubrication: To lubricate the pipeline and pump, it is highly recommended to add 10-20ml of castor oil per 10L canister.
- Software: Software can be upgraded using a download cable from SPARK FABRICA.
Diagram Description: The diagram shows a nozzle assembly with an O-ring. It labels the "Nozzle" and the "O-Ring".
7. Warranty Instructions
Thank you for choosing the SPARK FABRICA I FLAMER SF-90. The product warranty period is one year. If any quality problems arise within 7 days of shipping, Spark Fabrica will exchange it for a brand new, same model machine.
Spark Fabrica offers free maintenance service for machines with hardware malfunctions (excluding damage caused by human factors) during the warranty period. Do not attempt to repair the machine without factory permission.
Situations NOT included in warranty service:
- ⚠️ Damage caused by improper transportation, usage, management, and maintenance, or damage caused by human factors.
- ⚠️ Disassembly, modification, or repair of products without SPARK FABRICA permission.
- ⚠️ Damage caused by external reasons (e.g., lightning strike, power supply issues).
- ⚠️ Damage caused by improper installation or use.
For product damage not covered by the warranty, paid service can be provided.
Warranty Card
Invoice and warranty card are necessary when applying for maintenance service from SPARK FABRICA.
| Product Name: | Serial No: |
| Purchase Date: | |
| Tel: | |
| Address: | |
| Info. Feedback About The Problem: | |
| Actual Problem: | |
| Maintenance Detail: | |
| Service Engineer: | Service Date: |