Altronix Home
Installation Guide for Altronix models including: T1PHK1F4S 4 Door Kit with Fused Outputs, T1PHK1F4S, 4 Door Kit with Fused Outputs
Altronix T2PHK33F16 | 16-Door Access and Power Integration K
Altronix T2PHK77F24D | 24-Door Altronix/Openpath Access and
File Info : application/pdf, 8 Pages, 984.81KB
DocumentDocumentAccess & Power Integration T1PHK1F4S T1PHK1F4SD 4 Door Kit with Fused Outputs 4 Door Kit with PTC Outputs Fully assembled kit includes: Fully assembled kit includes: - Trove1 enclosure with TC1 Altronix/Openpath backplane - One (1) eFlow4NB - Power Supply/Charger - One (1) ACM4 - Fused Access Power Controller - One (1) VR6 - Voltage Regulator - One (1) PDS8 - Dual Input/Output Fused Power Distribtuion Module - Trove1 enclosure with TC1 Altronix/Openpath backplane - One (1) eFlow4NB - Power Supply/Charger - One (1) ACM4CB - PTC Access Power Controller - One (1) VR6 - Voltage Regulator - One (1) PDS8CB - Dual Input/Output PTC Power Distribtuion Module T1PHK3F8 8 Door Kit with Fused Outputs Fully assembled kit includes: - Trove1 enclosure with TC1 Altronix/Openpath backplane - One (1) eFlow6NB - Power Supply/Charger - One (1) ACM8 - Fused Access Control Module T1PHK3F8D 8 Door Kit with PTC Outputs Fully assembled kit includes: - Trove1 enclosure with TC1 Altronix/Openpath backplane - One (1) eFlow6NB - Power Supply/Charger - One (1) ACM8CB - PTC Access Control Module T2PHK33F16 16 Door Kit with Fused Outputs Fully assembled kit includes: - Trove2 enclosure with TCV2 Altronix/Openpath backplane - Two (2) eFlow6NB - Power Supply/Chargers - Two (2) ACM8 - Fused Access Control Modules T2PHK33F16D 16 Door Kit with PTC Outputs Fully assembled kit includes: - Trove2 enclosure with TCV2 Altronix/Openpath backplane - Two (2) eFlow6NB - Power Supply/Chargers - Two (2) ACM8CB - PTC Access Control Modules T2PHK77F24 24 Door Kit with Fused Outputs Fully assembled kit includes: - Trove2 enclosure with TCV2 Altronix/Openpath backplane - Two (2) eFlow104NB - Power Supply/Chargers - Three (3) ACM8 - Fused Access Control Modules T2PHK77F24D 24 Door Kit with PTC Outputs Fully assembled kit includes: - Trove2 enclosure with TCV2 Altronix/Openpath backplane - Two (2) eFlow104NB - Power Supply/Chargers - Three (3) ACM8CB - PTC Access Control Modules All components of these Trove kits are UL Listed sub-assemblies. Please refer to the included corresponding Sub-Assembly Installation Guides for further information. Installation Guide All registered trademarks are property of their respective owners. More than just power.TM Rev. TPHK_080921 Installing Company: _________________________ Service Rep. Name: __________________________________________ Address: _________________________________________________________ Phone #: _________________________ Overview: Altronix Trove Openpath kits are pre-assembled and consist of Trove enclosures/backplanes with factory installed Altronix power supply/chargers and subassemblies. These kits also accommodate various combinations of Openpath boards for up to twenty four (24) doors in a single enclosure. Altronix Model Number T1PHK1F4S T1PHK1F4SD Power Supply Board Input Fuse Rating Power Supply Board Battery Fuse Rating 120VAC 60Hz Input Current (A) Fail-Safe/Fail-Secure or Dry Form "C" Outputs Additional Fuse or PTC Protected Outputs ACM4/ACM4CB Board Input Fuse Rating ACM4 Board Output Fuse Rating ACM4CB Board Output PTC Rating ACM8(CB) Board Input Fuse Rating ACM8 Board Output Fuse Rating ACM8CB Board Output PTC Rating PDS8 Board Input Fuse Rating PDS8 Board Output Fuse Rating PDS8CB Board Input PTC Rating PDS8 Board Output PTC Rating Configuration Chart: Maximum Supply Current for Main and Aux. Outputs on Power Supply board, ACM4(CB)/ ACM8(CB) Access Power Controllers' or PDS8(CB) outputs Nominal DC Output Voltage Power Supply [DC] [Aux] Output Output Range Range (VDC) (VDC) 3.5 24VDC @ 3.7A 20.17- 20.2826.4 26.4 4 8 3A/ 10A/ 32V 32V 10A/ 3A/ 32V 32V 2.5A 9A 2.5A T1PHK3F8 T1PHK3F8D 5A/ 15A/ 250V 32V 3.5 T2PHK33F16 7.0 T2PHK33F16D T2PHK77F24 T2PHK77F24D 6.3A/ 15A/ 250V 32V 9.0 24VDC @ 5.9A 24VDC @ 5.9A + 24VDC @ 5.9A 24VDC @ 9.7A + 24VDC @ 9.7A 20.17- 20.2826.4 26.4 8 2.5A/ 250V 2.5A 20.1726.4 20.2826.4 16 10A/ 250V 2.5A/ 250V 2.5A 20.1726.4 20.2826.4 24 2.5A/ 10A/ 250V 250V 2.5A Installation Instructions: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Product is intended for indoor use only. 1. Remove backplane from enclosure. Do not discard hardware. 2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install two/three upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure's upper keyholes over the two/three upper screws; level and secure. Mark the position of the lower two/three holes. Remove the enclosure. Drill the lower holes and install the fasteners. Place the enclosure's upper keyholes over the upper screws. Install the lower screws and make sure to tighten all screws. 3. Mount included UL Listed tamper switch(es) (Altronix Model TS112 or equivalent) in desired location, opposite hinge. Slide the tamper switch bracket onto the edge of the enclosure approximately 2" from the right side (Fig. 1, pg. 2). Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device. To activate alarm signal open the door of the enclosure. 4. Mount Openpath boards to backplane, refer to pages 3-6. 5. Refer to the eFlow Power Supply/Charger Installation Guide (eFlow4NB, eFlow6NB, eFlow104NB) and corresponding Sub-Assembly Installation Guide (ACM4(CB), ACM8(CB), PDS8(CB) and VR6) for Fig. 1 further installation instructions. Enclosure Edge of Enclosure Tamper Switch (included) To Access Control Panel or UL Listed Reporting Device - 2 - Trove Openpath Kits T1PHK1F4S(D): Configuration of Openpath Boards 1. Mount appropriate Openpath boards into the correct positions by postioning pre-mounted spacers over appropriate holes on the backplane and depressing down on board to secure spacer to the backplane (Fig. 2, pg. 3). 2. Fasten TC1 backplane to Trove1 enclosure utilizing pan head screws (provided). Access Controller Position Chart for the Following Openpath Modules: Openpath OP-ACC OP-EX-4E OP-EX-8E OP-16EM Mounting Position A B C D Fig. 2 L G N AC1 NC C NO NC C NO AC FAIL BAT FAIL AC DC + INP --- T + RET --INTERFACE TRIGGER EOL NO GND SUPERVISED Altronix - eFlow4NB ON - BAT + - DC + A B OFF - 24V ON - 12V IN2 Fuse + INP1 - + INP2 - PWR1+ IN1 Fuse PWR1+ Altronix - PDS8(CB) P P COM(-) PWR2+ OUT1 OUT2 OUT3 OUT4 N OUT5 OUT6 OUT7 OUT8 1 2 3 4 5 6 7 8 Common Power Outputs (NEG) N COM(-) PWR2+ VR6 is mounted below PDS8(CB) and connected via 8-pin connector TRIGGER INPUT TRG IN GND 1 IN GND 2 IN GND 3 IN GND 4 Altronix - ACM4(CB) LED1 LED2 LED3 LED4 NC C NO COM NC C NO COM OUTPUT 1 OUTPUT 2 NC C NO COM NC C NO COM OUTPUT 3 OUTPUT 4 MAIN --- + --- + D C RESET NO C NC FACP +AUX- Control Power Trove Openpath Kits - 3 - T1PHK3F8(D): Configuration of Openpath Boards 1. Mount appropriate Openpath boards into the correct positions by postioning pre-mounted spacers over appropriate holes on the backplane and depressing down on board to secure spacer to the backplane (Fig. 3, pg. 4). 2. Fasten TC1 backplane to Trove1 enclosure utilizing pan head screws (provided). Openpath OP-ACC OP-EX-4E OP-EX-8E OP-16EM Access Controller Position Chart for the Following Openpath Modules: Mounting Position A B C D Fig. 3 IN GND IN GND IN GND IN GND IN GND IN GND IN GND IN GND 1 2 3 4 5 NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM OUTPUT 1 OUTPUT 2 L G N OUTPUT 3 OUTPUT 4 6 AC1 NC C NO NC C NO AC FAIL BAT FAIL AC DC TRIGGER EOL NO GND SUPERVISED RESET +AUX- Altronix - eFlow6NB ON OUTPUT 6 OUTPUT 5 Altronix - ACM8(CB) 8 7 OUTPUT 7 OFF - 24V ON - 12V OUTPUT 8 - BAT + - DC + A B - +- + POWER CONTROL NO C NC FACP +IMP - T + RET INTERFACE D C - 4 - Trove Openpath Kits T2PHK33F16(D): Configuration of Openpath Boards 1. Mount appropriate Openpath boards into the correct positions by postioning pre-mounted spacers over appropriate holes on the backplane and depressing down on board to secure spacer to the backplane (Fig. 4, pg. 5). 2. Fasten TC2 backplane to Trove2 enclosure utilizing pan head screws (provided). Openpath OP-ACC OP-EX-4E OP-EX-8E OP-16EM Access Controller Position Chart for the Following Openpath Modules: Mounting Position A B C D Fig. 4 ON OFF - 24V ON - 12V Altronix - eFlow6NB L G N AC1 AC DC NC C NO NC C NO AC FAIL BAT FAIL TRIGGER EOL NO GND SUPERVISED RESET +AUX- ON OFF - 24V ON - 12V Altronix - eFlow6NB L G N AC1 AC DC NC C NO NC C NO AC FAIL BAT FAIL TRIGGER EOL NO GND SUPERVISED RESET +AUX- IN GND IN GND IN GND IN GND IN GND IN GND IN GND IN GND 1 2 3 4 5 6 7 8 Altronix - ACM8(CB) NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8 IN GND IN GND IN GND IN GND IN GND IN GND IN GND IN GND 1 2 3 4 5 6 7 8 Altronix - ACM8(CB) NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8 - BAT + - DC + - BAT + - DC + NO C NC FACP +IMP - T + RET INTERFACE - +- + POWER CONTROL NO C NC FACP +IMP - T + RET INTERFACE A A B C B C D D - +- + POWER CONTROL Trove Openpath Kits - 5 - T2PHK77F24(D): Configuration of Openpath Boards 1. Mount appropriate Openpath boards into the correct positions by postioning pre-mounted spacers over appropriate holes on the backplane and depressing down on board to secure spacer to the backplane (Fig. 4, pg. 5). 2. Fasten TC2 backplane to Trove2 enclosure utilizing pan head screws (provided). Openpath OP-ACC OP-EX-4E OP-EX-8E OP-16EM Access Controller Position Chart for the Following Openpath Modules: Mounting Position A B C D Fig. 4 Altronix - eFlow104NB L G N AC1 AC DC 1 min enable NC C NO NC C NO AC FAIL BAT FAIL 2 hr disable TRIGGER EOL NO GND SUPERVISED RESET + AUX - --- BAT + --- DC + A B C --- DC + Altronix - eFlow104NB L G N AC1 AC DC 1 min enable NC C NO NC C NO AC FAIL BAT FAIL 2 hr disable TRIGGER EOL NO GND SUPERVISED RESET + AUX - TRIGGER INPUT IN GND IN GND IN GND IN GND IN GND IN GND IN GND IN GND 1 2 3 4 5 6 7 8 F1 F2 F3 F4 F5 F6 F7 F8 FACP TRG ON ON 1234 1234 Altronix - ACM8(CB) NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8 TRIGGER INPUT IN GND IN GND IN GND IN GND IN GND IN GND IN GND IN GND 1 2 3 4 5 6 7 8 F1 F2 F3 F4 F5 F6 F7 F8 FACP TRG ON ON 1234 1234 Altronix - ACM8(CB) NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8 --- BAT + -+-+ Power Control NO C NC +INP- T + RET- -+-+ Power Control NO C NC +INP- T + RET- FACP INTERFACE FACP INTERFACE B C D B DC TRIGGER INPUT IN GND IN GND IN GND IN GND IN GND IN GND IN GND IN GND 1 2 3 4 5 6 7 8 F1 F2 F3 F4 F5 F6 F7 F8 FACP TRG ON ON Altronix - ACM8(CB) 1234 1234 NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8 INTERFACE NO C NC +INP- T + RET- FACP -+-+ Power Control - 6 - Trove Openpath Kits T1PHK1F4S(D) and T1PHK3F8(D) (Trove1) Enclosure Dimensions (H x W x D approximate): 18" x 14.5" x 4.625" (457mm x 368mm x 118mm) 14.5" (321.3mm) 7.25" (184.2mm) 1.45" (36.8mm) 1.95" (49.5mm) 1.5" (38.1mm) 4.5" (114.3mm) 1.25" (31.8mm) 0.57" (14.5mm) 0.6" (15.2mm) 13.0" (330.2mm) 1.25" (31.8mm) 1.5" (38.1mm) 8.5" (215.9mm) 8.5" (215.9mm) 18.0" (457.2mm) 6.5" (165.1mm) 6.5" (165.1mm) 0.6" (15.2mm) 1.1" (27.9mm) 4.5" (114.3mm) 4.5" (114.3mm) 2.75" (69.9mm) 1.115" (28.3mm) 1.36" (34.5mm) 1.25" (31.8mm) Trove Openpath Kits - 7 - T2PHK33F16(D) and T2PHK77F24(D) (Trove2) Enclosure Dimensions (H x W x D approximate): 27.25" x 21.5" x 6.5" (692.2mm x 552.5mm x 165.1mm) 2.00" (50.8mm) 21.50" (546.1mm) 5.25" (133.35mm) 3.5"(88.9mm) 3.5"(88.9mm) 5.25" (133.35mm) 2.00" (50.8mm) 1.25" (31.8mm) 6.25" (158.8mm) 1.25" (31.8mm) 1.5" (38.1mm) 0.5625" (14.3mm) 0.685" (17.4mm) 1.77" (45mm) Knockouts 1.125" (28.3mm) 2.415" (61.3mm) 0.885" (22.5mm) 19.80" (502.9mm) 6.25" (158.8mm) 2.00" (50.8mm) 6.75" (171.5mm) 8.25" (209.5mm) 27" (685.8mm) 8.00" (203.2mm) 1.00" (25.4mm) 0.85" (21.6mm) 1.25" (31.8mm) 2.00" (50.8mm) 2.00" (50.8mm) 5.25" (133.4mm) 7.00" (177.8mm) 5.25" (133.4mm) 1.25" (31.8mm) 2.00" (50.8mm) Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 web site: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty IITrove Openpath Kits H09U - 8 - MEMBER Trove Openpath Kits