Arenti P2Q Smart Pan Tilt Wi-Fi Camera

Quick start guide

1. Packing list
2. Product description
3. Installation
4. Product configuration
5. Specification
6. Legal notice

1. Packing list

The packing list includes:

• Camera X1
• Power adapter X1
• Power cable X1
• Bracket X1
• Screws X3
• Quick guide X1

2. Product description

The camera features the following components:

1. LED indicator

2. Microphone

3. Speaker

4. Reset button

5. Power port

6. SD card slot

Notice

To reset the device, press and hold the reset button for 5 seconds. The camera will beep upon completion.

LED indicator status:

3. Installation

1. Use the included mounting bracket to fix the camera to a clean surface.
2. Alternatively, place the camera on a flat surface.

4. Product configuration

Download and install the Arenti APP by scanning the QR code or searching for "Arenti" on the App Store (iOS) or Google Play (Android).

Registration

Open the Arenti App. New users should tap to create an account and follow the on-screen prompts. Ensure you agree to the Privacy Agreement.

Pairing

On the App's home page, click "+" or "Add Device" and select the appropriate camera icon.

Power on the device. After approximately 30 seconds, the camera will emit a start-up tone, and the LED indicator will flash red slowly.

Note: During pairing, place the camera and mobile phone close to the router. If the camera does not enter the red slow blinking state after 30 seconds of powering on, press and hold the reset button for 5 seconds to reset and reconfigure the network.

Select your Wi-Fi network and input the password, then click "Next". Ensure your phone is connected to a stable Wi-Fi network.

Scan the QR code displayed on your phone with the camera. Once the camera emits a "dong dong dong" sound and the LED indicator turns solid blue, click "Next".

Troubleshooting connection issues:

• Ensure your Wi-Fi network is 2.4GHz or 5GHz.
• Verify the Wi-Fi password is correct and that your mobile device is connected to the same network.
• Confirm the camera is in pairing mode.
• Check your WiFi for network activity.

For further assistance, please contact support@arenti.com.

Notice:

• For multiple cameras, repeat the steps to add each device individually.
• To change the Wi-Fi network, restore the camera to factory settings and follow the setup steps again.

5. Specification

6. Legal notice

Support: www.arenti.com

Symbols

Do not dispose of batteries or used products with household waste. Dispose of them through designated collection points to protect health and the environment.

Arenti declares that the radio equipment type 'P2Q' complies with Directive 2014/53/EU. The full EU declaration of conformity is available at: www.arenti.com

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated with the provided instructions. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution!

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Safety Information

Power Adapter Safety:

1. The power plug is intended to serve as a disconnect device. Do not drop or impact the power adapter.
2. If the power cable is damaged (e.g., cord is exposed or broken) or the plug is loose, stop using it immediately. Continued use may lead to electric shocks, short circuits, or fire.
3. Do not touch the device or the power adapter with wet hands, as this may lead to short circuits, malfunctions, or electric shocks.

Child's safety:

1. Comply with all child safety precautions. Allowing children to play with the device or its accessories may be dangerous.
2. The device and its accessories are not intended for use by children. Children should only use the device with adult supervision.

Operation safety:

1. Use the device under the allowed humidity and temperature conditions.
2. Do not aim the device at strong light sources (such as lamplight or sunlight) when focusing, to avoid reducing the lifespan of the CMOS sensor and causing overbrightness and flickering.
3. Observe local laws and regulations, and respect the privacy and legal rights of others.

Restrictions declaration in the 5 GHz band:

(i) The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

(ii) Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.

© 2023. All rights reserved. All trade names are registered trademarks of respective companies. Apple, the Apple logo, iPhone are trademarks of Apple Inc. registered in the U.S. and other countries. Google, the Google logo, Android are trademarks of Google Inc. App Store is a service mark of Apple Inc. Google Play is a service mark of Google Inc.

Version 1.0 202306.