User Guide for Blaupunkt models including: TYRE INFLATOR, TIF 22 DA - 12V

22DA manual

Admin

Download Manual

Blaupunkt India


File Info : application/pdf, 4 Pages, 2.35MB

PDF preview unavailable. Download the PDF instead.

Tyre Inflator TIF 22 DA - 12V
TIF 22 DA - 12V

TTYIFRE2I2NFDLAAT-O1R2V
Suitable for Car, Motorcycle, Bicycle and other Sports equipment
Multiple Adaptors Included

BPIN Private Limited 47, Atlanta Society, Nariman Point, Mumbai - 400 021. Maharashtra. India. Toll Free: 1800 209 6820 | info@blaupunktcar.in | Shop Online at www.blaupunktcar.in

TIF 22 DA - 12V Product Description

1. Digital Guage 3. LED Lamp 5. LED lamp turn ON 7. Power Cord

2. Carry Handle 4. Quick Release Nozzle Inflator Rubber Hose 6. Inflator ON / OFF Switch 8. Cigarette Lighter Adaptor

Specification: Y Inflator with Digital Gauge & AutoStop
Y Input: DC 12V Y Rated Power: 100W
Y Rated Current: 8A Y Max Pressure: 120 PSI / 8.2 BAR Y Cylinder diameter: 22mm Y Max. Duty Cycle: 8 min Y Recommended for Sedans & Hatchback vehicles Y Function:Tyre inflator with PRESET & AUTOSTOP Y Additional Function: LED work light Y Power Cord length: 3 meter with cigarette lighter plug. Y Air hose: 50cm rubber hose with quick release valve connector Y Accessories: 2 nozzle adaptors & 1 sports equipment needle nozzle

TIF 22 DA - 12V
Instructions: 1. Start the vehicle and insert the cigarette lighter adaptor
into the 12V cigarette lighter outlet provided in the vehicle. 2. The device comes with a 3M long Power Cord which makes it convenient to connect the front & back tyres . Fig. 1 3. Attach the Quick Release Nozzle to the valve stem of the tyre. 4. Place the device on a preferably flat surface and set the preferred tyre pressure on the digital dial (Fig 2). 5. Turn on inflator device. Make sure there are no leaks at the point where the quick release nozzle meets the valve stem of the tyre. 6. Once the desired tyre pressure is reached, the unit turns off automatically.

Current Air Pressure

Unit Display

"-" Key

"+" Key

Unit Switch" Button
Fig. 2

7. This tyre pressure inflator comes equipped with a LED

light that makes it convenient to use at night.

8. This device is designed to work non stop for around 7-

8 minutes (typical time required to inflate 13"-16"

tyres). It is suggested to not use the device beyond

these 7-8 minutes at a stretch. A 2-3 minute interval

may be required to improve the efficiency of this

Fig. 3

device in the long run.

TIF 22 DA - 12V

Product Parameters: Input Voltage Power Cord
Length MAX Duty
Cycle

DC 12V 3 Meters
< 8 min

Power

100W

Cylinder Diameter 22MM

MAX Air Pressure 120PSI

Helpful Tips:
1. Do NOT keep the device near a heat source 2. Do NOT use this device near flammable liquids or gas source 3. Should the device need attention, please visit an Authorized Service
Centre. Any attempt to service the device by unauthorised person will VOID warranty 4. This device is designed to be used with a 12V supply source only. Do NOT attempt to use it with a 24V supply source 5. This device is designed to be used to inflate tires of Sedans and small diameter tyres only. 6. It is normal for the device to get hot after continuous use. 7. It is recommended to use this device to inflate tyres for no longer than it's suggested cycle time at a go.
Accessories: Following accessories are included in the package: 1 qty spare fuse and 3 qty multi - function air inflator nozzles.

TIF 22 DA - 12V

Troubleshooting Guide
This section covers common problems the user may encounter while using this device.

Nature of problem Device not working
Device is operating erratically

Cause and recommended solution Fuse is blown - replace fuse and check device The quick release valve connector is not connected to the valve stem securely - causing a leak and hence showing erratic readings. Release the connector from the valve stem and reconnect securely
The preferred tire pressure was not preset correctly and causes the display to blink continuously. Turn off the device, set the preferred tyre pressure and Turn ON device.

Steps for changing fuse:

Unscrew the top of the cigarette lighter
adaptor

Remove blown fuse & insert spare fuse provided

Screw the top end of the cigarette lighter adaptor to make a
tight seal

TIF 22 DA - 12V

TIF 22 DA - 12V



References

Corel PDF Engine Version 21.3.0.755 CorelDRAW 2019