McIntosh MAC7200 Stereo Receiver Owner's Manual

Owner's Manual for McIntosh models including: MAC7200 Stereo Receiver, MAC7200, Stereo Receiver, Receiver

958MAC7200

958MAC7200, McIntosh MAC7200, WWW.CRUTCHFIELD.COM

958MAC7200;, McIntosh, MAC7200;, WWW.CRUTCHFIELD.COM;

JOSHN

McIntosh MAC7200 owner's manual

McIntosh MAC7200 Stereo receiver at Crutchfield

File Info : application/pdf, 55 Pages, 12.89MB

958MAC7200

McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 www.mcintoshlabs.com
MAC7200 Receiver Owner's Manual

Important Safety Information is supplied in a separate document "Important Additional Operation Information Guide"

Thank You
Your decision to own this McIntosh MAC7200 Receiver ranks you at the very top among discriminating music listeners. You now have "The Best." The McIntosh dedication to "Quality," is assurance that you will receive many years of musical enjoyment from this unit. Please take a short time to read the information in this manual. We want you to be as familiar as possible with all the features and functions of your new McIntosh.
Please Take A Moment
The serial number, purchase date and McIntosh Dealer name are important to you for possible insurance claim or future service. The spaces below have been provided for you to record that information: Serial Number: _______________________________
Purchase Date: _______________________________
Dealer Name: ________________________________
Technical Assistance If at any time you have questions about your McIntosh product, contact your McIntosh Dealer who is familiar with your McIntosh equipment and any other brands that may be part of your system. If you or your Dealer wish additional help concerning a suspected problem, you can receive technical assistance for all McIntosh products at:
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903 Phone: 607-723-3512 Fax: 607-724-0549

Customer Service
If it is determined that your McIntosh product is in need of repair, you can return it to your Dealer. You can also return it to the McIntosh Laboratory Service Department. For assistance on factory repair return procedure, contact the McIntosh Service Department at:
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903 Phone: 607-723-3515 Fax: 607-723-1917
Table of Contents
Safety Instructions.............................................................. 2 (Separate Sheet) ............................Important Additional Operation Information Guide
Thank You and Please Take a Moment ...............................2 Technical Assistance and Customer Service.......................2 Table of Contents ................................................................. 2 General Information ............................................................ 3 Connector and Cable Information ....................................... 4 Introduction ......................................................................... 5 Performance Features ...................................................... 5-6 Dimensions .......................................................................... 7 Installation ........................................................................... 8 Connections: Rear Panel Connections....................................................... 9 (Separate Sheet) ...........................................................Mc1A Connecting Components ................................................... 10 Connection Diagrams (Separate Sheet).................Mc2A/2B Passthru Connections ........................................................ 11 Connecting for Bi-Amplification ...................................... 12 Connecting Loudspeakers ............................................ 13-14 Remote Control and Front Panel: Remote Control Push-buttons ........................................... 16 How to use the Remote Control......................................... 17
Copyright 2017 © by McIntosh Laboratory, Inc.

Front Panel Displays, Controls, Push-buttons and Jack ....................................................... 18
Setup Mode: How to Operate the Setup Mode ....................................... 19
Setup Functions: Default Settings .........................................................19 Firmware Version ......................................................19 Source Input Renaming ....................................... 20-21 Output Settings ..........................................................21 Power Control Triggers 1 and 2.................................22 Data Ports...................................................................23 Passthru ......................................................................23 USB Automute ...........................................................23 Comm Port Baud Rate ...............................................24 Remote Control Codes...............................................24 IR Sensor....................................................................24 Power Mode ...............................................................25 Tuner Presets..............................................................25 Tuner Regions ............................................................25 Factory Reset .............................................................27 Microprocessor Reset ........................................................ 27
Operation: How to Operate the MAC7200.....................................28-36
Trim Functions: Balance .......................................................................28 Trim Level..................................................................29 Tone Control...............................................................29 Bass ............................................................................29 Treble..........................................................................30 Phono Adjustments ....................................................30 Mono/Stereo Mode ....................................................30 Meter Backlight .........................................................31 Display Brightness.....................................................31 Headphone HXD........................................................31 Tone, Trim, Mute........................................................ 31 Headphone Jack, Power Output Meters, Power Guard, Separate Power Amplifier, Using Output 2 ............... 32 Passthru, Optical and Coaxial Digital Inputs ............ 33 Operating the FM and AM Tuner .........................33-34 AM or FM Band Selection.................................... 33 Default Station Tuning...................................... 33 Seek Tuning Type ............................................. 33

Table of Contents, con't
Operating the FM and AM Tuner, con't Direct Access Tuning........................................ 34 Preset Tuning .................................................... 34 Create a Preset ............................................ 34 Erase a Preset .............................................. 34 Selecting a Preset ........................................ 34 Tuner Text ......................................................... 34 USB Input Operation with a Computer ....... 35-36
Specifications....................................................... 37-38 Packing Instructions ................................................. 39

General Information
1. For additional connection information, refer to the owner's manual(s) for any component(s) connected to the MAC7200.
2. Apply AC Power to the MAC7200 and other McIntosh Component(s) only after all the system components are connected together. Failure to do so may cause a malfunction of system operations as the Microprocessor's Circuitry inside the components is active when AC Power is applied.
3. The MAC7200 includes an Auto Off Power Save Feature and the default setting is enabled. For additional information including how to disable it, refer to page 22.
4. When Power Amplifier Protection Circuitry of the MAC7200 has activated, the Front Panel Power Guard LEDs are illuminated continuously and the sound will be muted.
5. When the Power Transformer has overheated due to improper ventilation and/or high ambient operating temperature, AC Power is removed from the MAC7200. Normal operation will resume when the operating temperature is in a safe range again.
6. For the best performance and safety, it is important to always match the impedance of the Loudspeaker to the Power Amplifier connections. Refer to pages 13 and 14. Note: The impedance of a Loudspeaker actually varies as the Loudspeaker reproduces different frequencies. As a result, the nominal impedance rating of the Loudspeaker (usually measured at a midrange frequency) might not always agree with the impedance of the Loudspeaker at low frequencies where the greatest amount of power is required. Contact the Loudspeaker Manufacturer for additional information about the actual impedance of the Loudspeaker before connecting
it to the McIntosh MAC7200.

7. The MAC7200 Remote Control is capable of operating other components. For additional information go to www.mcintoshlabs.com.
8. RF Multipath interferance can occur when the MAC7200 receives two or more signals from the Tuned in FM Broadcast Station. The first signal received is the direct signal from the station and additional signals received are delayed because they have reflected off of a building or terrain (hill/mountain). This delay results in an increase in distortion and a reduction in Stereo Separation. To reduce or eliminate Multipath, reorient the direction of the FM Antenna for minimum indication of Multipath even if the Signal Strength indicates less signal. Refer to pages 33 and 34.
9. The IR Input, with a 1/8 inch mini phone jack, is configured for non-McIntosh IR sensors such as Xantech Model DL85K Kit. Use a Connection Block such as a Xantech Model ZC21 when two or more IR sensors need to be connected to the MAC7200. The signal from a connected External IR Sensor will have priority over the signal from the Front Panel IR Sensor.
10. When discarding the unit, comply with local rules or regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with the local regulations concerning battery disposal.
11. For additional information on the MAC7200 and other McIntosh Products please visit the McIntosh Web Site at www.mcintoshlabs.com.

General Information, Connector and Cable Information

Connector and Cable Information

XLR Connectors

Below is the Pin configuration for the XLR Balanced Input

Connectors on the MAC7200. Refer to the diagram for con-

nection:

PIN 1: Shield/Ground

PIN 2: + Output

PIN 3: - Output

PIN 1

PIN 2

PIN 3

Power Control and Trigger Connectors

The Power Control Trigger Output Jacks send and Passthru Input Jack receives Power On/Off Signals

Main, Trig 1&2 and Pass-Thru

(+12 volt/0 volt) when connected to other McIntosh Components. An additional connection is for controlling the illumination of the

Power Control
Meter Illumination Control Ground

Power Output Meters on McIntosh

Power Amplifiers. A 3.5mm stereo mini phone plug is

used for connection to the Power Control, Trigger and

Passthru Outputs.

Data Port Connectors The Data Out Ports send Remote Control Signals to Source Components. A 3.5mm stereo mini phone plug is used for connection.

Data Signal
N/C Data Ground

IR IN Port Connectors The IR IN Port also uses a 3.5mm stereo mini phone plug and allows the connection of other brand IR Receivers to the MAC7200.

IR Data Control
N/C
Ground

RS232-C Data Port Cable The RS232 Data Cable is a 3.5mm stereo mini phone plug to a subminiature DB 9 connector:

Data In (DB9-pin2)
Data Out (DB9-pin3)
Ground (DB9-pin5)

DB9

(male connector)

PIN 1

PIN 5

PIN 6

PIN 9

Output Terminal Connector When cables with spade lugs are used for Loudspeaker Connection, the spade lugs need an opening of at least 3/10 inch (7.6mm).

3/10 of an inch (7.6millimeters)

McIntosh Plug-In Jumper Connector The MAC7200 utilizes two phono style Plug-In Jumpers to connect the Preamplifier Output to the Power Amplifier Input.
Note: The Jumper Connector is available from the McIntosh Parts Department: McIntosh Jumper Connector Part
No. 117781

FM Dipole Antenna The MAC7200 FM Tuner Circuitry requires the connection of an external Antenna for FM reception. A "FM Dipole Antenna" is available from the McIntosh Parts Department:
FM Dipole Antenna Part No. 173033

McIntosh RAA2 AM Antenna The AM Tuner Circuitry requires the connection of the external McIntosh RAA2 Antenna for AM reception. The RAA2 Antenna is supplied with the MAC7200 Receiver. The "AM Antenna" is also available from the McIntosh Parts Department:
RAA2 AM Antenna with connecting cable Part No. 31036400

Introduction and Performance Features

Introduction
Now you can take advantage of traditional McIntosh standards of excellence in the MAC7200 Receiver.
The flexible Preamplifier section provides connections for various input sources and may also be used to drive an external Power Amplifier(s).
The AM/FM Tuner section provides superb reception from Radio Stations. It uses the latest in technology for the best sound quality, along with the convenient operation.
The Power Amplifier section of the MAC7200, with a power output of 200 watts per channel, will drive a pair of quality Loudspeakers to a high level of performance.
The MAC7200 reproduction is sonically transparent and absolutely accurate. The McIntosh Sound is "The Sound of the Music Itself."
Performance Features
· Power Output with Patented Autoformer The MAC7200 consists of a 200 watts per channel Power Amplifier with less than 0.005% distortion. The McIntosh designed and manufactured Autoformer allows connection of 2, 4 or 8 ohm Loudspeakers. The Power Amplifier uses ThermalTrak1 Output Transistors for lower distortion and cool operation.
· Power Guard The patented McIntosh Power Guard circuit prevents amplifier clipping and protects your valuable Loudspeakers.
· Sentry Monitor and Thermal Protection McIntosh Sentry Monitor power output stage protection circuits ensure the MAC7200 will have a long and
1 ThermalTrakTM and ON Semiconductor are trademarks of Semiconductor Components Industries, LLC

trouble free operating life. Built-in Thermal Protection Circuits guard against overheating.
· Power Meters The Illuminated Power Output Meters are peak responding, and indicate the power output of the amplifier.
· McIntosh Custom Binding Posts McIntosh Patented gold plated Power Amplifier Output Terminals deliver high current output. They accept large diameter wire and spade lugs. Banana plugs may also be used only in the United States and Canada.
· Electronic Switching and Balanced Connections The Preamplifier uses Logic Circuits Controlled Electromagnetic Switches on all inputs and operating functions for reliable, noiseless, distortion free switching. There is a Balanced Input for connection of a source component.
· Digital Audio Inputs The Digital Inputs decode PCM and DSD Signals from external sources. Coaxial and Optical Inputs process Digital Signals up to 192kHz with 24-Bit resolution. The Digital MCT Input Circuitry directly decodes SACD/CD signals from an external Transport component. The USB Input for streaming audio processes Digital Signals up to 384kHz with 32-Bit resolution, decodes up to DSD256 Digital Signals and DXD 24-Bit with a sampling rate up to 384kHz.
· Moving Coil and Moving Magnet Phono Inputs The MAC7200 has two precision Phono Preamplifier Circuits for Moving Coil and Moving Magnet Phono Cartridges. Both circuits use the latest designs to provide the lowest possible noise, distortion and flat

frequency response. The MC Phono Cartridge Input has selectable loading.
· Tone Controls The Bass and Treble Trim Controls provide up to 12dB of boost or cut. The MAC7200 remembers the Bass and Treble Setting for each input.
· Multifunction Display The Front Panel Display indicates source selection, volume levels and setup functions. For Tuner operation it also indicates Station Frequency, Signal Strength, Stored Station Presets and Tuner Setup Functions.
· Special FM RF Circuitry The Tuner Module RF Circuitry receives strong local FM Station Signals without distortion and receives even the weakest of FM Signals with low noise.
· High Dynamic Range IF FM Circuitry The all important IF circuitry in the Tuner Module provides dynamic bandwidth control optimizing performance at all times with varying reception conditions.
· Information Service The Front Panel Display can display various text information from the Broadcast Station2. This text information may include the Station Call Sign, Music Genre, Artist Name and Song Title.
2 The display of text information is dependent on the Broadcast Station transmitted signal, the text information language and the Broadcast Station country of origin. The Tuner Module supports English Language Alphabet Characters.
5

Performance Features, con't
· Preset Stations and Permanent Memory Twenty AM and Twenty FM station presets make it easy to listen to your favorite stations. Station Presets and Function Modes are retained in Permanent Memory even when AC power is switched Off.

· Glass Front Panel The famous McIntosh Illuminated Glass Front Panel using long life Light Emitting Diodes (LEDs) ensures the pristine beauty of the MAC7200 will be retained for many years.

· RAA2 External AM Antenna The RAA2 External AM Antenna provides the perfect match to the Tuner Module AM Circuitry. The 20 foot (6 meter) connection cable allows placement of the AM Antenna away from electronic equipment which can produce RF Interference to weak AM signals.

· Power Control Output and Trigger Assignment A Power Control connection for convenient Turn-On of McIntosh Power Amplifiers, Source Components and Accessories is included. The Power Control Trigger Ouputs may be assigned to activate when a given Input/Output is selected.

· PassThru Mode The Automatic PassThru Mode allows the MAC7200 to become part of a Multichannel Sound System for DVD-Audio, SACD and Home Theater Movies.

· Remote Control The Data Ports together with the supplied Remote Control provide control of McIntosh Source Components connected to the MAC7200.

· Special Power Supply The large Power Transformer, multiple filter capacitors with 120 Joules of Energy Storage and regulated Power Supply, ensures stable noise free operation even though the power line varies.

Dimensions
The following dimensions can assist in determining the best location for your MAC7200. There is additional information on the next page pertaining to installing the MAC7200 into cabinets.
Front View of the MAC7200
17-1/2"
44.5cm

USB

DSD256

35%

Rear View of the MAC7200 16-1/16"
40.8cm
12-3/16"
31cm

Dimensions

7 -1/8"
18.1cm

7 -5/8"
19.4cm

Side View of the MAC7200 18-3/4"
47.6cm
16-1/2"
41.9cm

6"
15.2cm

29/32"
1.8cm
1-5/8"
4.1cm

13"
33cm

3/16"

6-1/4"
15.9cm

0.5cm

1"
2.5cm

Installation The MAC7200 can be placed upright on a table or shelf, standing on its four feet. It also can be custom installed in a piece of furniture or cabinet of your choice. The four feet may be removed from the bottom of the MAC7200 when it is custom installed as outlined below. The four feet together with the mounting screws should be retained for possible future use if the MAC7200 is removed from the custom installation and used free standing. The required panel cutout, ventilation cutout and unit dimensions are shown.
Always provide adequate ventilation for your MAC7200. Cool operation ensures the longest possible operating life for any electronic instrument. Do not install the MAC7200 directly above a heat generating component such as a high powered amplifier. If all the components are installed in a single cabinet, a quiet running ventilation fan can be a definite asset in maintaining all the system components at the coolest possible operating temperature.
A custom cabinet installation should provide the following minimum spacing dimensions for cool operation.
Allow at least 6 inches (15.24cm) above the top, 2 inches (5.08cm) below the bottom and 2 inches (5.1cm) on each side of the Integrated Amplifier, so that airflow is not obstructed. Allow 20 inches (50.8cm) depth behind the front panel. Allow 1-7/6 inch (3.66cm) in front of the mounting panel for knob clearance. Be sure to cut out a ventilation hole in the mounting shelf according to the dimensions in the drawing.
8

17-1/16"
43.34cm

Installation

MAC7200 Front Panel Custom Cabinet Cutout

USB

DSD256

35%

6 -5/8"
16.83cm

Cabinet Front Panel
Opening for Ventilation

6"
15.2cm

Cutout Opening for Custom Mounting

MAC7200 Side View in Custom Cabinet

MAC7200 Bottom View in Custom Cabinet

2"
5.1cm

Note: Center the cutout Horizontally on the unit. For purposes of clarity, the above illustration is not drawn to scale.

Cutout Opening for Ventilation

1"
2.5cm

Support Shelf

14-1/2"
36.8cm
Cutout Opening
for Ventilation

13"
33cm

13-5/16"
33.8cm

Chassis Spacers
15-1/16"
38.3cm

Rear Panel Connections
The identification of Rear Panel Connections for the MAC7200 Receiver is located on a separate folded sheet contained in the Owner's Manual Packet. Refer to separate sheet "Mc1A" for the Rear Panel Connections.

MAC7200 Receiver

MAC7200 Rear Panel Connections

Connecting Components

Connecting Components
The MAC7200 has the ability to automatically switch power On/Off to McIntosh Source Components via the Power Control (Trigger) connections. The Data Port Connections allow for the remote operation of basic functions using the MAC7200 Remote Control. With an external sensor connected to the MAC7200, remote control operation of the system is possible from another room and/or when the MAC7200 is located in a cabinet with the doors closed.
The connection instructions below, together with the MAC7200 Input and Output Connection Diagrams located on the separate folded sheet "Mc2A/2B", are an example of a typical audio system. Your system may vary from this, however the actual components would be connected in a similar manner. For additional information refer to "Connector and Cable Information" on page 4. Power Control Connections:
1. Connect a Control Cable from the MAC7200 POWER CONTROL MAIN Jack to the Power Control In on the Turntable.
2. Connect a Control Cable from the McIntosh Turntable Power Control Out Jack to the Digital Audio Player Trigger In Jack.
3. Connect a Control Cable from the Digital Audio Player Trigger Out Jack to the SACD/CD Transport Power Control In Jack.
4. Connect a Control Cable from the SACD/CD Transport Power Control Out Jack to the Media Server PWR CTRL (Power Control) In Jack.
5. Optionally connect a Control Cable from the MAC7200 POWER CONTROL TRIG (Trigger) 2 Jack to the Power Amplifier (Secondary Room) Power Control In Jack.
6. Connect any additional McIntosh Components in a similar manner, as outlined in steps 1 thru 5.

Data Control Connections: 7. Connect a Control Cable from the MAC7200 DATA PORT Jack 2 to the SACD/CD Player Data In Jack. 8. Connect a Control Cable from the MAC7200 Jack 1 to the Media Server Data In Jack. 9. Connect any additional McIntosh Components in a similar manner, as outlined in steps 7 thru 8.
Sensor Connection: 10. Optionally, connect the cable with stereo mini
plug coming from the compatible External Sensor to the EXT CTRL (External Control) IR IN Jack on the MAC7200. Refer to page 3 "General Information, note 8" for additional information. Audio Connections: 11. Connect Balanced Cables from the MAC7200 BALANCED INPUT L & R Connectors to the Media Server Audio Output Balanced Connectors. 12. Connect Audio Cables from the MAC7200 Number 1 UNBALANCED Jacks to the AM/FM Tuner UNBAL Output Jacks. 13. Connect the Audio Cables coming from the Turntable to the MAC7200 MC (for a Moving Coil Cartridge) or MM (for a Moving Magnet Cartridge) INPUT Jacks. 14. Optionally, connect Audio Cables from the MAC7200 OUTPUT 2 Jacks to the Power Amplifier (Secondary) Input Jacks. 15. Connect any additional Components in a similar manner, as outlined in steps 11 thru 14. Optional Digital Audio Connections: 16. Connect an Optical Cable from the MAC7200 OPTICAL 1 Digital Audio Input Connector to the Digital Audio Out Optical Connector on the Digital Audio Player.

17. Using the "MCT Cable-Twisted Pair" cable (supplied with a MCT Transport), connect the cable from the MAC7200 MCT DIGITAL AUDIO INPUT Connector to the SACD/CD Transport MCT (DIN) Output Connector.
18. Connect any additional Components in a similar manner, as outlined in steps 17 thru 18.
Optional USB Connection: 19. Connect a USB cable with (Type A to Type B)
connectors from the MAC7200 USB D/A Digital Audio Input to an available USB connector. Antenna Connection: 20. Connect a FM Antenna (or Cable System) to the FM ANT 75 Ohm Connector. 21. Connect the supplied McIntosh RAA2 AM Antenna and connection cable cable to the RAA2 AM ANT Connector. Ground Connections: 22. Connect the Ground Cable coming from the Turntable to the MAC7200 GND Binding Post.
Notes: 1. If the MAC7200 is part of a Home Theater System, proceed to "PassThru" connection on page 11.
2. When the MAC7200 will used together with a separate Power Amplifier for Bi-Amplification of a Loudspeaker System, proceed page 12.

Passthru Connections
The MAC7200 can be part of a Multichannel Sound System for BLU-RAY-Audio, DVD-Audio and Home Theater Movies. The Right and Left Front Channels from an Audio/Video Control Center can "Passthru" the MAC7200. In the following example the UNBALANCED 5 Input will become the "Passthru" input:
1. Connect Audio Cables from the A/V Processor FL (Front Left) and FR (Front Right) Channel Outputs to the MAC7200 UNBALANCED Number 5 INPUTS Left and Right Jacks.
2. Connect a Control Cable from the A/V Processor TRIGger 2 Output to the MAC7200 POWER CONTROL PASSTHRU INPUT Jack. Note: Refer to Setup "Passthru" on page 23 to assign the Number 5 INPUT as the "Passthru" Input.
3. Proceed to "Connecting Loudspeaker" on Page 11.

A/V Processor

Passthru Connections

Connecting for Bi-Amplification
The MAC7200 Power Amplifier, together with an additional separate Power Amplifier, may be used to Bi-Amplify a Loudspeaker System. In the illustration on this page, the Power Amplifier of the MAC7200 is connected to the Midrange/High Frequency Section of the Loudspeaker. The additional separate Power Amplifier is connected to the Low Frequency Section of the Loudspeaker System.
Warning: The Loudspeaker System used for Bi-Amplification must have the jumpers removed from between the MID/HIGH and LOW Frequency Sections of the Loudspeaker System. Failure to remove them could result in damage to the MAC7200 and/or the separate Power Amplifier.
MAC7200 Connections: 1. Remove the "McIntosh Jumpers" from between the OUTPUT 1 Jacks and the PWR AMP In Jacks located on the Rear Panel of the MAC7200. Note: Place the "McIntosh Jumper" in a safe place for possible future use. 2. Using a pair of shielded RCA Type Audio "Y" Adapters connect the OUTPUT 1 Jacks to the PWR AMP In Jacks, for both Left and Right Channels. 3. Connect the remaining unconnected part of the "Y" Adapters to the separate Power Amplifier. 4. Referring to the Loudspeaker Connection Instructions on page 13, and in the Owner's Manual supplied with the Power Amplifier and Loudspeaker, connect the MAC7200 Output Terminals to the Loudspeaker MID/HIGH Input Terminals. Note: The Loudspeaker Connection illustrations on this page are for the Left Channel. Connect the Right Channel Loudspeaker in the same manner.
12

"Y" adapter Cable 3RZHU$PSOL¿HU

Connecting for Bi-Amplification
Left Channel Loudspeaker
-+

Output Terminals

When connecting the Loudspeaker Hookup Cables to

the MAC7200 Amplifier Output Terminals please fol-

low the steps below:

1. Rotate the top of the Output Terminal Post coun-

terclockwise until an opening

DSSHDUV5HIHUWR¿JXUHV$DQG

2. Insert the Loudspeaker hookup

cable into the Output Terminal

Opening

Post opening or the cable spade lug around the center post of Figure A Figure B

the Output Terminal. Refer to

¿JXUH&

3. Rotate the top of the Output

Terminal Post clockwise until it

LV¿QJHUWLJKW5HIHUWR¿JXUH'

4. Place the supplied McIntosh Figure C Figure D Wrench over the top of the Out-

put Terminal and rotate it one

quarter of a turn (90°) to secure

the Loudspeaker Cable Connec-

tion. Do not over tighten. Refer

Figure E

WR¿JXUH(

How to Connect Loudspeakers
Caution: Do not connect the AC Power Cord to the MAC7200 Rear Panel until after the Loudspeaker Connections are made. Failure to observe this could result in Electric Shock.
The connection instructions below, together with the MAC7200 Connection Diagram located on the separate folded sheet "Mc2B", is an example of a typical audio system. Your system may vary from this, however the actual components would be connected in a similar manner. For additional information refer to "Connector and Cable Information" on page 4.

The McIntosh MAC7200 Power Amplifier Circuitry is designed for Loudspeakers with an impedance of 2 ohms, 4 ohms or 8 ohms. Connect a single Loudspeaker only to the Right and Left Output Terminals.
When connecting Loudspeakers to the MAC7200 it is very important to use cables of adequate size, so there is little to no power loss in the cables. The size is specified in Gauge Numbers or AWG (American Wire Gauge). The smaller the Gauge number, the larger the wire size:

Loudspeaker Cable Distance vs Wire Gauge Guide

Loudspeaker Impedance

25 feet (7.62 meters)
or less

50 feet (15.24 meters)
or less

100 feet (30.48 meters)
or less

2 Ohms

12AWG

10AWG

8AWG

4 Ohms

14AWG

12AWG

10AWG

8 Ohms

16AWG

14AWG

12AWG

1. Prepare the Loudspeaker Hookup Cable for attachment to the MAC7200 Power Amplifier: Bare wire cable ends: Carefully remove sufficient insulation from the cable ends, refer to figures F, G & H. If the cable is stranded, carefully twist the strands together as tightly as possible.

Figure F

Figure G Figure H

Notes: 1. If desired, the twisted ends can be tinned with solder to keep the strands together.
2. The prepared bare wire cable ends may be inserted into spade lug connectors.
3. Banana plugs are for use in the United States and Canada only.

Banana Plugs are for use in the United States and

Canada only:

2. Attach the previously prepared bare wire cable ends

into the banana plugs and secure

the connections. Refer to figure I.

3. Rotate the Output Terminal Post

FORFNZLVHXQWLOLWLV¿QJHUWLJKW 5HIHUWR¿JXUH-7KHQXVLQJWKH

Figure I

McIntosh Wrench, rotate the top of

the Output Terminal one quarter of

a turn (90°). Do not over tighten.

5HIHUWR¿JXUH(

4. Referring to figure K, connect the

Loudspeaker hookup cables with Figure J banana plugs into the hole at the

top of the terminal to

the MAC7200 Negative

Output Terminal and

Positive Output Termi-

QDOLQGHQWLILHGDV

RKPVRKPVRU RKPVFRQQHFWLRQ

Figure K

to match the impedance of the Loudspeaker, being

careful to observe the correct polarities.

Note: The illustration located on the separate

folded sheet "Mc2B" is for connection to an

RKPV/RXGVSHDNHU

If the Loudspeaker's impedance is in-between

the available connections, use the nearest lower

impedance connection. Refer to "General Informa-

tion" Note 6 on page 3 for additional information.

WARNING: Loudspeaker terminals are hazard-

ous live and present a risk of electric

shock. For additional instruction on

making Loudspeaker Connections con-

tact your McIntosh Dealer or McIn-

tosh Technical Support.

5. Connect the MAC7200 power cord to an active AC outlet.
Spade Lug or Wire Connections: 6. Connect the Loudspeaker hookup cables to the MAC7200 Negative Output Terminal and PosiWLYH2XWSXW7HUPLQDOLQGHQWLILHGDVRKPV RKPVRURKPVFRQQHFWLRQWRPDWFKWKH impedance of the Loudspeaker, being careful to observe the correct polarities. Insert the spade lug connector or prepared section of the cable end into the terminal side access hole, and tighten the terminal cap until the cable is firmly clamped into the terminals so the lugs or wire cannot slip out. Refer to figures L and M. Note: The illustration located on the separate folded sheet "Mc2B"LVIRUFRQQHFWLRQWRDQ (ohms) Loudspeaker.

Figure L

Figure M

If the Loudspeaker's impedance is in-between the available connections, use the nearest lower impedance connection. Refer to "General Information" Note 6 on page 3 for additional information.
WARNING: Loudspeaker terminals are hazardous live and present a risk of electric shock. For additional instruction on making Loudspeaker Connections contact your McIntosh Dealer or McIntosh Technical Support.
7. Connect the MAC7200 power cord to an active AC outlet.

Connecting Loudspeakers

LEDs illuminate during the time a remote command is sent and when programming the remote control
Select the DEVICE to issue a remote control command to
SETUP Push-button is used as a "Shift Key" to select a function with blue color nomenclature
Selects AM Tuner Operating Functions, select Output 1 when used with the SETUP/shift Push-button and Track Selection on certain McIntosh CD Players
Press the Trim Push-button and then the LEVEL UP Push-button to select and adjust various functions. MENU is used with McIntosh Models displaying choices on a video screen Activates the TRIM Mode. GUIDE is used with McIntosh Models displaying instructions on a video screen
Press the Trim Push-button and then the LEVEL DOWN Push-button to select and adjust various functions. INFO is used with McIntosh Models displaying information on a video screen
Scrolls through the available INPUTS
Mutes the audio
Selects transport functions of STOP, PLAY/PAUSE, RECORD, BACK for the previous-selection, FAST-REVERSE, FAST-FORWARD and NEXT for the next selection
Selects Previous Tuner Station PRESET
Tuner scans Down the dial to SEEK the next Station
16

HR085 Remote Control Push-Buttons
Press to Power the Integrated Amplifier ON Use to select tuner presets, direct access an AM/FM Station Frequency, disc tracks or any numbered operation Press to Power the Integrated Amplifier OFF Direct access to stored Tuner PRESETS when used with the numeric Push-buttons (0 thru 9) Selects FM Tuner Operating Functions, select Output 2 when used with the SETUP/shift Push-button and Track Selection on certain McIntosh CD Players Use S and T to tune Up or Down the AM/FM Dial, use X and W for the next or previous HD Radio Program (were applicable)
EXIT the TRIM Menu and is used with McIntosh Models displaying information or choices on a video screen
Used to SELECT/Enter the indicated choice Press to change Broadcast BANDs on a connected Tuner. Select certain functions on a variety of McIntosh Models
Adjusts the VOLume level up or down
Selects Next Tuner Station PRESET
Tuner scans Up the dial to SEEK the next Station
Note: Push-buttons whose function is not identified above are for use with other McIntosh Products.

How to use the Remote Control
The supplied MAC7200 Remote Control (HR085) is capable of directly controlling the functions of contemporary McIntosh Source Components connected to the MAC7200 via the Data Ports.
Notes: 1. If at any time the MAC7200 seems unresponsive to the HR085 Remote Control Commands, press the DEVICE Push-button to select first.
2. For additional information on using the HR085 Remote Control with the McIntosh Model, please refer to the "How to Operate" starting on page 28.
3. For additional information on assigning the Data Ports, refer to "Data Ports" on page 23.

the next available station. Press and hold a Directional Up S or Down T Push-button to tune continuously
from station to station.

Trim Press the TRIM Push-button until the desired Trim function (Balance, Trim Level, etc.) appears on the MAC7200 Front Panel Display, then press the LEVEL Up or Down Push-button to adjust the Trim setting.
Note: Press the TRIM Push-button to recall the last Trim function selected. For additional information on using the Trim Functions refer to "How to Operate" page 28.

Output Selection Press the BLUE (Setup) Push-button followed by the AM (Output 1) or FM (Output 2) Push-button, to control the Rear Panel Audio OUTPUTS 1, 2 (ON or OFF) and Power Control TRIG 1 / TRIG 2.
Note: For additional information on assigning the Outputs (1 and 2) and Power Control Triggers (1 and 2) refer to page 22.

Tuner Push-buttons
Press the AM or FM Push-button to select the desired broadcast band. Press and release the Seek Up the band or Seek Down the band Push-button to seek

How to use the HR085 Remote Control
17

INPUT Control used to select a source for listening and recording. The control is also used to enter the TRIM or SETUP Modes and select the various functions

LED indicates when the Left Channel Amplifier POWER GUARD circuit activates
Meter indicates the Left Channel Output of the amplifier

Front Panel Displays, Controls, Push-buttons and Jack

LED indicates when the Right Channel Amplifier POWER GUARD circuit activates
Meter indicates the Right Channel Output of the amplifier

VOLUME Control allows adjustment of the listening level for both channels. Also used to change the various TRIM and SETUP Functions

Connection for low impedance dynamic headphones, for private listening

USB

DSD256

35%

STANDBY/ON Pushbutton with indicator switches the MAC7200 ON or OFF (Standby) and resets the microprocessors

PRESET Control selects Presets for listening or storing the desired radio station

INFORMATION DISPLAY indicates the Sources, Volume, other Audio Settings, Tuner Functions, other Operational Functions and Setup Mode Settings

TONE Push-button with indicator, when deactivated the audio signal bypasses the Tone Settings

TUNE tunes in radio stations and is also used for various Tuner Functions

OUTPUT 1 and 2 Push-buttons with indicators, switch Preamplifier Output (Loudspeakers) 1 and 2 On or Off

IR Sensor receives commands from a Remote Control

MUTE Push-button mutes the audio from the Loudspeakers and Headphones

Setup

How to Operate the Setup Mode
Your McIntosh MAC7200 has been factory configured to allow immediate enjoyment of superb audio without the need for further adjustments. If you wish to make changes to the factory default settings, a Setup Feature is provided to customize the operating settings using the Front Panel Information Display. Refer to the MAC7200 Front Panel Illustration on the previous page while performing the following steps.
Note: If the MAC7200 is currently On, proceed to step 2. 1. Press the STANDBY/ON Push-button on the Front Panel or press the (Power ON) Push-button on the Remote Control to switch On the MAC7200. The MAC7200 will go through a brief startup initialization with the Front Panel Information Display first indicating "MAC7200", followed by the last used source and volume setting. This is followed by the volume setting indication starting at zero and then increasing to the last used volume setting. Refer to figure 1.

BAL

15%

Figure 1
2. Press and hold in the INPUT Control until the Front Panel Information Display indicates "MAC7200 V1.00, (or higher Main Firmware version) - S/N: AFN____" (Serial Number). Refer to figure 2.

MAC7200

V1.00

S/N: AFN____

Figure 2

3. Rotate the INPUT Control to select the Setup Mode Menu item, "SETUP: Inputs, (Hold INPUT)". Refer to figure 3.

SETUP: Inputs (Hold INPUT)

Figure 3
Continue to rotate the INPUT CONTROL to view the other SETUP Mode Options. 4. To exit from the SETUP Mode, press and hold in the INPUT Control and the Front Panel Display will indicate its normal display. Refer to figure 1.

Default Settings

The Default Settings Chart below indicates the Function Name, Default Setting and the Page Number for additional information.

Default Settings

Function Name

Setting

Page No.

MAC7200

V_._ _

DA1

V_._ _

TUNER FIRMWARE TM________

INPUTS

On / Rename

OUTPUTS (1 & 2)

Switched

TRIGGER 1

Output 1

TRIGGER 2

Output 2

DATA PORTS (1 thru 4)

All Data

PASSTHRU

OFF

USB Automute

RS232 (Rate)

115200 Baud

Remote Control Codes

Normal

IR Sensor

Enabled

Power Mode

Enabled

Tuner Presets

---

Tuner Region

USA

Firmware Version
The MAC7200 functionality is controlled by internal software that is know as Firmware. There are three Firmware Identification Numbers for the MAC7200. The first Firmware Number is for the Main Circuitry of the MAC7200 and can be identified at any time by utilizing the Setup Mode.
1. Press and hold in the INPUT Control to enter Setup Mode.
2. Referring to the Front Panel Information Displaythe number after the character "V" is the Firmware number. Refer to figure 2.
To view the second Firmware Number (the Digital Audio Circuitry of the MAC7200) or the third Firmware Number (the Tuner Circuitry of the MAC7200), perform the following steps:
3. Press and hold in the INPUT Control to enter Setup Mode.
4. Rotate the INPUT Control until the Front Panel Information Display indicates "DA1 Firmware, V1.00" (or higher Digital Audio Firmware version). Refer to figure 4.
DA1 FIRMWARE V1.00
Figure 4
4. Rotate the INPUT Control until the Front Panel Information Display indicates "TUNER FIRMWARE Firmware, V1.00" (or higher Digital Audio Firmware version). Refer to figure 5.
TUNER FIRMWARE TM30104101
Figure 5
5. To exit the Setup Mode, press the INPUT Control.

Input Settings
The MAC7200 provides the ability to switch unused INPUTS Off (or back On if they have been previously switched Off). The default INPUT Names can be changed to match the name of the component connected to it or any other custom name desired (within 10 Characters). INPUT SWITCHED ON/OFF: In the following example, the UNBAL 4 Input will be switched Off.
Note: When an INPUT is swiched Off, its name will no longer appear on the Front Panel Information Display when using the INPUT Control (Front Panel or Remote Control).
1. Press and hold in the INPUT Control to enter the SETUP MODE. Refer to figure 2 on page 19.
2. Rotate the INPUT Control until "SETUP: Inputs, (Hold INPUT)" appears on the Information Display. Refer to figure 3 on page 19.
3. Press and hold in the INPUT Control until "SETUP: UNBAL 4, On / Name (Hold INPUT)" appears on the Display. If necessary rotate the INPUT Control to select the UNBAL 4 Input. Refer to figure 6.
SETUP: UNBAL 4 On/Name (Hold INPUT)
Figure 6
4. To switch the UNBAL 4 Input Off, rotate the VOLUME Control until the display indicates "SETUP: UNBAL 4, Off". Refer to figure 7.
SETUP: UNBAL 4 Off
Figure 7
5. Exit the SETUP Mode by several presses of the INPUT Control.

In the following example, the UNBAL 4 Input will be switched On.
Notes: 1. When a desired INPUT is selected, its name will appear on the Front Panel Information Display when using the INPUT Control (Front Panel or Remote Control).
6. Press and hold in the INPUT Control to enter the SETUP MODE. Refer to figure 2, on page 19.
7. Rotate the INPUT Control until "SETUP: Inputs, (Hold INPUT)" appears on the Information Display. Refer to figure 3, on page 19.
8. Press and hold in the INPUT Control until "SETUP: UNBAL 4, Off" appears on the Display. If necessary rotate the INPUT Control to select the UNBAL 4 Input. Refer to figure 7.
9. To switch the UNBAL 4 Input On, rotate the VOLUME Control until the display indicates "SETUP: UNBAL 4, On / Name".
10. Exit the SETUP Mode by several presses of the INPUT Control.
RENAME INPUT: In the following example, the BAL (BALANCED) Input will be renamed to match up with the component connected (refer to page 10, step 11).
The MAC7200 Default Input Names (UNBAL 1, BAL, COAX 1, etc.) as indicated on the Front Panel Display can be customized to a different name up to ten characters long (TUNER, CD PLAYER, etc.). The available characters for renaming the input include the following: ! < > * , / - _ 0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z .
In the following example, the BAL Input will be renamed to "MEDIA SVR". 11. Press and hold in the INPUT Control to enter the
SETUP MODE. Refer to figure 2, on page 19. 12. Rotate the INPUT Control until "SETUP: Inputs,

(Hold INPUT)" appears on the Information Display. Refer to figure 8.

SETUP: Inputs (Hold INPUT)
Figure 8
13. Press and hold in the INPUT Control until "SETUP: BAL, On / Rename" appears on the Display. If necessary rotate the INPUT Control to select the BAL Input. Refer to figure 9.

SETUP: BAL On / Rename
Figure 9
14. Press and hold in the INPUT Control until "RENAME: BAL, >BAL < " appears on the Display. The character "B" is flashing to indicate it is ready to be changed. Refer to figure 10.

RENAME: BAL

>BAL

Figure 10

15. Rotate the VOLUME (ADJUST) Control to change

the character "B" to "M". Refer to figure 11.

RENAME: BAL

>MAL

Figure 11
16. Rotate the INPUT Control until the character "A" is flashing, then rotate the VOLUME (ADJUST) Control to change the character "A" to "E". Refer to figure 12.

RENAME: OPTI

>MEL

Figure 12

Setup, con't

17. Rotate the INPUT Control until the character "L" is flashing, then rotate the VOLUME (ADJUST) Control to change the character "L" to "D". Refer to figure 13.

RENAME: BAL

>MED

Figure 13

18. Rotate the INPUT Control until the "_" empty space to the right of character D is flashing, then

rotate the VOLUME (ADJUST) Control to change

the "_" empty space to character to "I". Refer to figure 14.

RENAME: BAL

>MEDI

Figure 14
19. Rotate the INPUT Control until the "_" empty space to the right of character I is flashing, then rotate the VOLUME (ADJUST) Control to change the "_" empty space to character to "A". Refer to figure 15.

RENAME: BAL

>MEDIA

Figure 15
20. Repeat step 19 until the new name of " RENAME: BAL, MEDIA SVR" is indicated on the Front Panel Display. Refer to figures 16 thru 18.

RENAME: BAL

>MEDIA S

Figure 16

RENAME: BAL

>MEDIA SV

Figure 17

RENAME: BAL >MEDIA SVR <
Figure 18
21. To save the new name, press and hold in the INPUT Control until "SETUP: MEDIA SVR , ON / Rename" appears on the Front Panel Information Display. Refer to figure 19.
SETUP: MEDIA SVR On / Rename
Figure 19
22. Exit the SETUP Mode by several presses of the INPUT Control. Note: For convenience, an "Input Assignment Chart" on a separate sheet "Mc5A/5B" has been provided to keep track of changes.
Output Settings
The Output Settings provide the ability to change how the MAC7200 Output 1, Output 2 and Headphones function. OUTPUT 1 and 2: By default OUTPUT 1 and 2 are set to go On/Off by using the Front Panel OUTPUT 1 and 2 Push-buttons or by using the OUTPUT 1 and 2 Push-buttons on the Remote Control. If it is desirable to have OUTPUT 1 and/or 2 always On regardless of the OUTPUT 1 and 2 Push-button settings, perform the following: 1. Press and hold in the INPUT Control to enter the
SETUP MODE. Refer to figure 2 on page 19. 2. Rotate the INPUT Control until "SETUP: Out-
puts, (Hold INPUT)" appears on the Information Display. Refer to figure 20. 3. Press and hold in the INPUT Control until

SETUP: Outputs (Hold INPUT)
Figure 20
"SETUP: OUTPUT 1, Switched" appears on the Display. Refer to figure 21.
SETUP: OUTPUT 1 Switched
Figure 21
4. Rotate the VOLUME (ADJUST) Control to change from the "Switched" setting to "Unswitched". Refer to figure 22.
SETUP: OUTPUT 1 Unswitched
Figure 22
5. In a similar manner, perform steps 3 and 4 to change the OUTPUT 2 setting. Refer to figures 23 and 24.
SETUP: OUTPUT 2 Switched
Figure 23
SETUP: OUTPUT 2 Unswitched
Figure 24
The MAC7200 Default Setting for using Headphones is to automatically mute all the Output Connectors when the Headphone Cable Plug is inserted into the MAC7200 Front Panel HEADPHONES Jack. There are two available settings:
Mute All Outputs Mute No Outputs 6. Rotate the INPUT Control until "SETUP: HEAD-
21

Output Settings, con't
PHONES, Mute All Outputs " appears on the Information Display. Refer to figure 25.
SETUP: HEADPHONES Mute All Outputs
Figure 25
7. Rotate the VOLUME (ADJUST) Control to change the current HEADPHONES setting from "Mute All Outputs" to "Mute No Outputs". Refer to figure 26.
SETUP: HEADPHONES Mute No Outputs
Figure 26
8. Exit the SETUP Mode by several presses of the INPUT Control.

Power Control Triggers 1 and 2
By default the Power Control TRIGger 1 and TRIGger 2 are assigned to activate when Output 1 or Output 2 is selected. Triggers 1 and 2 can be reassigned to function the same as the MAIN Power Control Jack or be assigned to a given Input.
Note: The MAIN Power Control Jack is controlled by the STANDBY/ON Front Panel Push-button and the Remote Control Power Push-buttons.
In the first example, the Power Control Triggers 1 and 2 will be assigned to MAIN: 1. Press and hold in the INPUT Control to enter the
SETUP MODE. Refer to figure 2 on page 17. 2. Rotate the INPUT Control until "SETUP: Trig-
gers, (Hold INPUT)" appears on the Information Display. Refer to figure 27.
SETUP: Triggers (Hold INPUT)
Figure 27
3. Press and hold in the INPUT Control until "SETUP: TRIGGER 1, Output 1" appears on the Display. Refer to figure 28.
SETUP: TRIGGER 1 Output 1
Figure 28
4. Rotate the VOLUME (ADJUST) Control to select "MAIN" from the available additional selections including Output 2 or Input. Refer to figure 29.
SETUP: TRIGGER 1 Main
Figure 29
5. In a similar manner, perform steps 3 and 4 to change the Trigger 2 setting from OUTPUT 2 to Main. Refer to figures 30 and 31.

SETUP: TRIGGER 2 Output 2
Figure 30
SETUP: TRIGGER 2 Main
Figure 31
In the second example, Trigger 2 will activate when the BAL Input is selected:
6. Rotate the INPUT Control to select "SETUP: TRIGGER 2, Main" appears on the Display. Refer to figure 30.
7. Rotate the VOLUME (ADJUST) Control until "SETUP: TRIGGER 2, Input (Hold INPUT)" appears on the Display. Refer to figure 32.
SETUP: TRIGGER 2 Input (Hold INPUT)
Figure 32
8. Press and hold in the INPUT Control until "SETUP: TRIGGER 2, Bal: OFF" appears on the Display. Refer to figure 33.
SETUP: TRIGGER 2 Bal : OFF
Figure 33
9. Rotate the VOLUME (ADJUST) Control to select "Bal : ON". Refer to figure 34.
SETUP: TRIGGER 2 Bal : ON
Figure 34
10. Exit the SETUP Mode by several presses of the INPUT Control.

Setup, con't

Data Ports
Data Port Connections between the MAC7200 and a McIntosh Source Component allow for basic function control of the source component using the MAC7200 supplied HR085 Remote Control. By default, all of the four Data Ports are set to send the same Data to the selected source. To dedicate a given Data Port for only one source component (example, source component connected to the BAL Input will be assigned to Data Port 1) perform the following Steps: 1. Press and hold in the INPUT Control to enter the
SETUP MODE. Refer to figure 2 on page 17. 2. Rotate the INPUT Control until "SETUP: Data
Ports, (Hold INPUT)" appears on the Information Display. Refer to figure 35.
SETUP: Data Ports (Hold INPUT)
Figure 35
3. Press and hold in the INPUT Control until "SETUP: DATA PORT 1, All Data" appears on the Display. Refer to figure 36.
SETUP: DATA PORT 1 All Data
Figure 36
4. Rotate the VOLUME (ADJUST) Control to select the "BAL" Input. Refer to figure 37.
SETUP: DATA PORT 1 BAL
Figure 37
5. In a similar manner, perform steps 3 and 4 to assign any additional Data ports.
6. Exit the SETUP Mode by several presses of the INPUT Control.

Passthru
When the MAC7200 is part of a Home Theater or Multichannel Audio System the Right and Left Front Channels from an Audio/Video Processor or Surround Decoder can "Passthru" from the assigned MAC7200 Input, into the MAC7200 Power Amplifier Circuitry. The "Passthru" Audio Signal is also available for a separate external Power Amplifier(s) via the number 1 Preamplifier Output Jacks. The Setup Mode allows selection of the specified MAC7200 Input to be used for the Right and Left Front Channels. In the example below, the Right and Left Front Channels from the Audio/Video Processsor will be connected to the UNBALANCED 6 INPUT Jacks on the MAC7200. Refer to page 9 for additional connection information.
Note: The Phono and Digital Inputs are not assignable as a Passthru Input.
1. Press and hold in the INPUT Control to enter the SETUP MODE. Refer to figure 2 on page 17.
2. Rotate the INPUT Control until "SETUP: Passthru, Off" appears on the Information Display. Refer to figure 38.
SETUP: Passthru Off
Figure 38
3. Rotate the VOLUME (ADJUST) Control to select "SETUP: Passthru, UNBAL 6" Input. Refer to figure 39.
SETUP: Passthru UNBAL 6
Figure 39
4. Exit the SETUP Mode by several presses of the INPUT Control.

USB Automute
The USB Automute Feature helps to ensure noise free playback of streaming music via the MAC7200 USB Input, as the Digital Audio Signal format changes (PCM, DSD, etc.). On occasion due to the way a Digtal Audio Music Recording was made, it may become desirable to switch Off the USB Automute Feature. To switch Off Automute, perform the following steps:
1. Press and hold in the INPUT Control to enter the SETUP MODE. Refer to figure 2 on page 17.
2. Rotate the INPUT Control until "SETUP: USB Automute, ON" appears on the Information Display. Refer to figure 40A.
SETUP: USB Automute ON
Figure 40A
3. Rotate the VOLUME (ADJUST) Control to select "SETUP: USB Automute, OFF" Input. Refer to figure 40B.
SETUP: USB Automute OFF
Figure 40B
4. Exit the SETUP Mode by several presses of the INPUT Control.

Comm Port Baud Rate
The MAC7200 may be remotely controlled from other equipment connected to the Rear Panel RS232 Jack. The speed at which the MAC7200 communicates (8 bit, no parity and 1 stop bit) with other equipment is adjustable from 9,600 bits per second to 115,200 bits per second. To change from the default speed of 115,200 bits per second, perform the following steps:
1. Press and hold in the INPUT Control to enter the SETUP MODE. Refer to figure 2 on page 17.
2. Rotate the INPUT Control until "SETUP: RS232, 115200 Baud" appears on the Information Display. Refer to figure 41.
SETUP: RS232 115200 Baud
Figure 41
3. Rotate the VOLUME (ADJUST) Control to select the desired Baud Rate Speed.
4. Exit the SETUP Mode by several presses of the INPUT Control.

Remote Control Codes
The HR085 Remote Control included with the MAC7200 utilizes the NORMAL McIntosh Control Codes. The Second Set of Control Codes the MAC7200 will respond to is referred to as the ALTERNATE Codes. The Alternate Codes are used when the MAC7200 is used in the same location as another McIntosh Preamplifier and/or A/V Processor. This will prevent the Remote Control from affecting the operation of both units at the same time. To activate the Remote Control ALTERNATE Codes perform the following steps:
1. Press and hold in the INPUT Control to enter the SETUP MODE. Refer to figure 2 on page 17.
2. Rotate the INPUT Control until "SETUP: IR Codes, Normal" appears on the Information Display. Refer to figure 42.
SETUP: IR Codes Normal
Figure 42
3. Rotate the VOLUME (ADJUST) Control to the Alternate Codes. Refer to figure 43.
SETUP: IR Codes Alternate
Figure 43
4. It is now necessary to change the HR085 Remote Control over to the Alternate Codes. Information on the HR085 Remote Control is available for download from the McIntosh Web Site: http://www.mcintoshlabs.com/us/Products/pages/ ProductDetails.aspx?CatId=preamplifiers&Produ ctId=MAC7200
5. Exit the SETUP Mode by several presses of the INPUT Control.

IR Sensor
The MAC7200 Front Panel Sensor, which receives the signals from the HR085 Remote Control, can be switched off to prevent interference when an external IR Sensor is connected. To de-activate the Front Panel IR Sensor perform the following steps:
1. Press and hold in the INPUT Control to enter the SETUP MODE. Refer to figure 2 on page 17.
2. Rotate the INPUT Control until "SETUP: Front IR, Enabled" appears on the Information Display. Refer to figure 44.
SETUP: Front IR Enabled
Figure 44
3. Rotate the VOLUME (ADJUST) Control to select Disabled. Refer to figure 45.
SETUP: Front IR Disabled
Figure 45
5. Exit the SETUP Mode by several presses of the INPUT Control.

Setup, con't

Power Mode
The MAC7200 incorporates an Auto Off Feature, which automatically places the preamplifier into the Power Saving Standby/Off Mode. This occurs approximately 30 minutes after there has been an absence of user activity (includes changes to any of the Operation Functions such as source selection, volume adjustment, etc.) or absence of an audio signal. If it is desirable to disable the Auto Off Feature perform the following steps:
1. Press and hold in the INPUT Control to enter the SETUP MODE. Refer to figure 2 on page 17.
2. Rotate the INPUT Control until "SETUP: Auto Off, Enabled" appears on the Information Display. Refer to figure 46.
SETUP: Auto Off Enabled
Figure 46
3. Rotate the VOLUME (ADJUST) Control to select Disabled. Refer to figure 47.
SETUP: Auto Off Disabled
Figure 47
4. Press the INPUT Control to exit the Setup Mode.

Tuner Presets
The MAC7200 AM/FM Tuner Setup Mode allows for adding and deleting Radio Station Presets. For detailed information about the MAC7200 Tuner Operation, including the easier way of entering and removal of Radio Station Presets refer to "How to Operation" the Tuner Functions on pages 33 and 34.
ENTERING PRESETS: Follow the steps below for entering a Radio Station into Preset Memory for quick recall: 1. Press and hold in the INPUT Control to enter the
SETUP MODE. Refer to figure 2 on page 17. 2. Rotate the INPUT Control until "SETUP: Tuner
Presets, (Hold INPUT)" appears on the Information Display. Refer to figure 48.
SETUP: Tuner Presets (Hold INPUT)
Figure 48
3. Press and hold in the INPUT Control until "FM Presets Set, (Hold INPUT)" appears on the Information Display. Refer to figure 49.
FM Presets Set (Hold INPUT)
Figure 49
Note: To enter AM Presets instead of FM Presets, rotate the INPUT Control unitl the Information Display indicates "AM Presets Set, (Hold INPUT). then continue with step 4.
4. Press and hold in the INPUT Control until "P1 = Open, (Hold INPUT to SAVE)" appears on the Information Display. Refer to figure 50.

P1 = Open (Hold INPUT to SAVE)
Figure 50 Note: If Presets were previously entered, the fre-
quency of the station will appear in place of the word "Open". 5. Rotate the Front Panel TUNING knob to choose the radio station to be entered as P1 (Preset Number 1). Refer to figure 51.
P1 = 89.3 MHz (Hold INPUT to SAVE)
Figure 51
6. To save FM Station 89.3Mhz as P1 Press and Hold in the Input Control. Refer to figure 52.
P1 = 89.3 MHz PRESET SAVED
Figure 52
7. To enter additional Radio Station Presets, first rotate the PRESET Control until another Preset (P2 thru P20) with the word "Open" appears. Then using the TUNING knob find the next station to be entered as a Preset.
DELETING PRESETS: Follow the steps below for deleting all the previously entered a Radio Station Presets from Memory: 1. Press and hold in the INPUT Control to enter the
SETUP MODE. Refer to figure 2 on page 17. 2. Rotate the INPUT Control until "SETUP: Tuner
Presets, (Hold INPUT)" appears on the Information Display. Refer to figure 53 on the next page.

Tuner Presets, con't
SETUP: Tuner Presets (Hold INPUT)
Figure 53
3. Press and hold in the INPUT Control until "FM Presets Erase ALL, (Hold INPUT)" appears on the Information Display. Refer to figure 54.
FM Presets Erase ALL (Hold INPUT)
Figure 54
Note: To delete AM Presets instead of FM Presets, rotate the INPUT Control until the Information Display indicates "AM Presets Erase All, (Hold INPUT)". then continue with step 4.
4. Press and hold in the INPUT Control until "FM Presets Erase ALL, FM PRESETS ERASED" appears on the Information Display. Refer to figure 55.
FM Presets Erase ALL FM PRESETS ERASED
Figure 55
5. Press the INPUT Control to exit the Setup Mode.

Tuner Regions
The MAC7200 Tuner is capable of receiving AM/FM Broadcasts in various parts of the world. The Broadcasters may use slightly different standards and the MAC7200 accommodates these differences.

Setting
USA JAPAN EUR 100 EUR 50

AM Band
530kHz - 1710kHz 522kHz - 1611kHz 522kHz - 1602kHz 522kHz - 1602kHz

FM Band

FM Spacing

87.9MHz - 107.9MHz

200kHz

76MHz - 90MHz

100kHz

87.5MHz - 108MHz

100kHz

87.5MHz - 108MHz

50kHz

The Tuner Region Default Setting is for the USA. To change the MAC7200 for the broadcast standards in your country follow the steps below:
Notes: 1. For additional information contact your McIntosh Dealer.
2. Changing the current Tuner Region will result in clearing of all the Station Presets.
1. Press and hold the INPUT CONTROL until the Front Panel Display indicates the Setup Mode is active. Refer to figure 2 on page 17.
2. Rotate the INPUT Control until "SETUP: Tuner Region, (Hold INPUT)" is indicated. Refer to figure 56.
SETUP: Tuner Region (Hold INPUT)
Figure 56
3. Rotate the INPUT Control until "SETUP: Tuner Region, USA" is indicated. Refer to figure 57.

SETUP: Tuner Region USA
Figure 57

In the following example, the Tuner Region Setting of USA will be changed to JAPAN:
4. Rotate the VOLUME Control to select the JAPAN Region. Refer to figure 58.
SETUP: Tuner Region JAPAN
Figure 58
5. Momentarily press the INPUT Control to set the new region. Refer to figure 59.
Set Region: JAPAN? (SAVE: Press Input)
Figure 59
6. Momentarily press the INPUT Control to set the new region. Refer to figure 60.
Set Region: JAPAN --SAVED--
Figure 60
7. Press the INPUT Control to exit the Setup Mode.

Setup, con't and Reset of the Microprocessors

Factory Reset
If it becomes desirable to reset all the adjustable settings (Setup and Trim Settings) to the factory default values, perform the following steps: 1. Press and hold in the INPUT Control to enter the
SETUP MODE. Refer to figure 2 on page 17. 2. Rotate the INPUT Control until "FACTORY RE-
SET, (Hold INPUT)" appears on the Information Display. Refer to figure 61.
FACTORY RESET (Hold INPUT)
Figure 61
3. Press and hold in the INPUT Control until "FACTORY RESET, In Progress!" appears on the Information Display, then release the INPUT Control. Refer to figures 62 and 63.
FACTORY RESET In Progress!
Figure 62
FACTORY RESET Completed!
Figure 63
4. Press the Front Panel STAND/BY Push-button to switch On the MAC7200.

Reset of the Microprocessors
In the unlikely event the controls of the MAC7200 stop functioning, the microprocessors can be reset by performing the following: 1. Press the STANDBY/ON Push-button until the
STANDBY/ON LED Indicator switches Off. 2. Then release the STANDBY/ON Push-button and
the MAC7200 will switch Off. 3. When the STANDBY/ON LED is illuminated
press the STANDBY/ON Push-button, the MAC7200 will resume normal operation.
Note: This can be performed with the MAC7200 On or in the Standby Mode.

How to Operate the MAC7200

Power On and Off The Red LED above the STANDBY/ON Push-button lights to indicate the MAC7200 is in Standby mode. To switch ON the MAC7200, Press the STANDBY/ ON Push-button on the Front Panel or press the (Power - Green) Push-button on the Remote Control. The MAC7200 will go through a brief startup initialization with the Front Panel Display indicating Power Guard is active, last used source and volume setting. This is followed by the volume setting indication starting at zero and then increasing to the last used volume setting. Refer to figures 70, 71, 72 and 73. To switch OFF the MAC7200, press the STANDBY/ON Push-button on the Front Panel or the (Power - Red) Push-button on the Remote Control.

BAL

15%

Figure 71 Note: For an explanation of the Remote Control
Push-button functions, refer to pages 16 and 17.

COAX 1

48kHz
Figure 72

30%

Source Selection
Rotate the INPUT Control to select the desired source or press the INPUT UpS or DownT Push-button on
the Remote Control. Refer to figures 70 and 73.

Volume Control
Rotate the Front Panel VOLUME Control or use the VOLume UpS or DownT Push-buttons on the Re-
mote Control for the desired listening level. Refer to
figures 70 and 73.

Trim Functions The MAC7200 has various Trim Selections with Adjustments. The Trim Functions include Balance, Input Trim Level, Tone Controls, Bass, Treble, Tuner Con-

USB

DSD256

35%

Figure 70 28

trol (when the Tuner FM or Tuner AM is Selected), Phono Cartridge MC Loading (when the Input is Selected), Mono/Stereo, Meter Backlight, Display Brightness and HXD Mode (when Headphones are connected). The Trim Settings are stored in memory independently for each Input Source Selected, except the Meter Illumination and Digital Audio Display settings of On or Off, which are the same for all inputs.
Note: Selection and Adjustment of all Trim Functions may be performed by pressing the Front Panel INPUT Trim Control and then rotating it to select the desired Trim Function. Then use the VOLUME Adjust Control to change the setting. Remote Control TRIM Push-Button together with the LEVEL UP/ Down Push-button may also be used. Refer to figures 70 and 73.
After approximately 5 seconds the Display returns to indicate the Source Selection and Volume Level.

BALANCE Listening balance varies with dif-

Figure 73

ferent program sources, room acoustics and listening

positions relative to the Loudspeakers. Use the Bal-

ance (Trim Function) as needed to achieve approxi-

How to Operate the MAC7200

mately equal listening volume levels in each Loudspeaker. To adjust the Balance perform the following: 1. Press the TRIM Push-button repeatedly on the Re-
mote Control until "L BALANCE R, || " appears on the Front Panel Display. Refer to figure 74.

BALANCE

Figure 74

Note: The Front Panel INPUT/Trim Control may also be used.
2. Rotate the VOLUME/Adjust Control or press the LEVEL UP / DOWN Push-buttons on the Remote Control to emphasize the Right Channel (refer to figure 75) or the Left Channel (refer to figure 76).

BALANCE

¦¦¦¦¦¦¦¦¦

Figure 75

BALANCE

¦¦¦¦¦¦¦¦¦

Figure 76

The Front Panel Display indicates the relative Balance changes. After approximately 5 seconds, the Display returns to indicate the Source Selection and Volume Level. To verify the Balance setting without changing it, use the TRIM Push-button and select Balance.

TRIM LEVEL Source Components can have slightly different volume levels resulting in the need to readjust the MAC7200 Volume Control when switching between different sources. The MAC7200 allows the adjustment of levels for each Source, ensuring the same relative volume. To adjust the Trim Level for the currently

selected Input Source perform the following steps: 1. Select "INPUT TRIM" as indicated on the Front Panel Information Display. Refer to figures 70, 73 and 77.
INPUT TRIM 0.0 dB
Figure 77
2. Adjust the Trim Level of each Input to match the average volume level of the Input most frequently listened to. The range of adjustment is ± 6.0dB in half dB steps. Refer to figures 78 and 79.
INPUT TRIM -2.5 dB
Figure 78
INPUT TRIM +4.0 dB
Figure 79
After approximately 5 seconds the Information Display returns to indicate the Source Selection and Volume Level.
TONE CONTROL The Tone Controls default setting is Off. The TRIM TREBLE and BASS Settings may be adjusted for the currently selected Input Source, by first setting the Tone Control Trim Setting to On. The LED above the TONE Push-button will be illuminated. When the Tone Controls are Disabled the previous settings for Treble and Bass are bypassed from the signal path. To deactivate Tone Controls perform the following: 1. Select the desired Input Source. 2. Press the TRIM Push-button on the Remote Con-
trol until "TONE CONTROLS, Off" appears on

the Front Panel Display. Refer to figure 80.
TONE CONTROLS Off
Figure 80
3. Press TRIM LEVEL UP / DOWN Push-button to activate the Tone Controls On. Refer to figure 81.
TONE CONTROLS On
Figure 81
After approximately 6 seconds the Display returns to indicate the Source Selection and Volume Level.
BASS The Intensity of the Low Frequencies in the music can be increased or decreased by using the Trim Select and Trim Adjust Controls. To make an adjustment perform the following: 1. Use the Front Panel INPUT/TRIM Control or press
the TRIM Push-button on the Remote Control until "BASS 0 dB" appears on the Front Panel Information Display. Refer to figure 82.
BASS 0 dB
Figure 82
2. Rotate the INPUT/TRIM Control or press the LEVEL + / - Push-buttons to increase (refer to figure 83) or decrease (refer to figure 84 on page 30) the volume level of the low frequencies.
BASS +12dB
Figure 83
29

How to Operate the MAC7200, con't
BASS -12dB
Figure 84
The Front Panel Display indicates the Bass changes in steps from +12dB to -12dB. After approximately 6 seconds the Display returns to indicate the Source Selection and Volume Level.
TREBLE The Intensity of the High Frequencies in the music can be increased or decreased by using the Trim Select and Trim Adjust Control. To make an adjustment perform the following: 1. Use the Front Panel INPUT/TRIM Control or the
TRIM Push-button on the Remote Control until "TREBLE, 0 dB" appears on the Front Panel Information Display. Refer to figure 85.
TREBLE 0 dB
Figure 85
2. Rotate the VOLUME/ADJUST Control or press the LEVEL UP / DOWN Push-buttons to increase

(refer to figure 86) or decrease (refer to figure 87) the volume level of the high frequencies.
TREBLE +12dB
Figure 86
TREBLE -12dB
Figure 87
The Front Panel Display indicates the Treble changes in steps from +12dB to -12dB. After approximately 6 seconds the Display returns to indicate the Source Selection and Volume Level.
PHONO ADJUSTMENTS When the MC Phono Input is selected, an additional TRIM SELECT FUNCTION becomes available for adjustment. Perform the following steps to make the Phono Trim Adjustment:
1. Select the MC Phono Source Input. 6HOHFW75,0³3+2125(6,67$1&(´DV
indicated on the Front Panel Information Display. Refer to figure 88.

USB

DSD256

35%

PHONO RESISTANCE 400O
Figure 88
3. Rotate the VOLUME/Adjust Control or press the LEVEL UP / DOWN Push-buttons on the Remote Control to select the Resistance Load that comes closest to the Phono Cartridge Makers recommended value.
After approximately 5 seconds the Alphanumeric Display returns to indicate the Source Selection and Volume Level.

MONO/STEREO MODE

By default the Stereo Mode is active for all Input

Sources however, any Input Source may be assigned

to Mono Mode. To change Stereo Mode to Mono for a

given Input Source, perform the following steps:

1. Select the desired Input Source.

2. Select "MONO / STEREO,

______" as

indicated on the Front Panel Information Display.

Refer to figure 89.

MONO / _S_T_E_R_E_O
Figure 89
3. To select MONO Mode adjust the TRIM LEVEL. Refer to figure 90.

M_O_N_O_ / STEREO
Figure 90
After approximately 5 seconds the Information Display returns to indicate the Source Selection and Volume Level.

Figure 70 30

How to Operate the MAC7200, con't

METER BACKLIGHT The MAC7200 Front Panel Meter Illumination may be switched On or Off by performing the following:
1. Select "METER LIGHTS, On" as indicated on the Front Panel Information Display. Refer to figures 70, 73 (on page 28) and 91.
METER LIGHTS On
Figure 91
2. Switch Off the Meter Illumination. Refer to figure 92.
METER LIGHTS Off
Figure 92
After approximately 5 seconds the Information Display returns to indicate the Source Selection and Volume Level.
Notes: 1. Meter Illumination of recent McIntosh Power Amplifiers will also switch On/Off when connected to the MAC7200 via a power control cable.
2. Some A/V Processors will provide an On/Off Control Signal when the MAC7200 Passthru Input Jack is connected to the A/V Processor via the power control cable.
INFORMATION DISPLAY ILLUMINATION The Brightness Level of the MAC7200 Front Panel Information Display can be adjusted from bright to dim by performing the following:
1. Select "DISPLAY BRIGHTNESS" as indicated on the Front Panel Information Display. Refer to figures 70, 73 (on page 28) and 93.
2. Reduce the Brightness level by adjusting the TRIM LEVEL. Refer to figure 94.

DISPLAY BRIGHTNESS
Figure 93
DISPLAY BRIGHTNESS
Figure 94
After approximately 5 seconds the Information Display returns to indicate the Source Selection and Volume Level.
HEADPHONE HXD When headphones are connected to the MAC7200 Front Panel Jack, an additional TRIM function becomes available. McIntosh's HXD brings the acoustical depth and spatiality of music normally heard with loudspeakers, to your headphones. The default setting is HXD On. To switch HXD Off perform the following: 1. Momentarily press the INPUT Control, then rotate
it to select "HEADPHONE HXD, On". Refer to figure 95.
HEADPHONES HXD On
Figure 95
2. To deactivate the HXD Mode rotate the VOLUME Adjust Control until the Front Panel Display indicates "HEADPHONE HXD, Off". Refer to figure 96.
HEADPHONES HXD Off
Figure 96

Tone Press the Front Panel TONE Push-button to activate the MAC7200 TREBLE and BASS Tone Control Circuitry for the currently selected Input Source. The LED above the TONE Push-button will illuminate. To bypass the TONE CONTROL CIRCUITRY for the currently selected Input Source press the TONE Pushbutton. The LED above the TONE Push-button will extinguish.

Trim Press the Front Panel INPUT/TRIM Control to activate the MAC7200 Trim Functions. Rotate the Front Panel INPUT/Trim Control to select the desired Trim Function and then rotate the VOLUME/Adjust Control to vary or make changes. Refer to figure 50. The Remote Control TRIM and LEVEL UP and LEVEL DOWN Push-buttons may also be used. Approximately 5 seconds after Trim Function Selection and/or adjustments have stopped, the MAC7200 will switch off the Trim Mode.

Mute Press the MUTE Push-button to Mute the Audio in Output 1 (Loudspeakers), Output 2 and Headphones. The audio signals present at the FIXED OUTPUT Jacks are not effected by activating the mute function. The Front Panel Display will indicate the Source Name and with the word MUTE in place of the actual volume setting. Refer to figure 97.

COAX 1

MUTE

48kHz

Figure 97

Pressing the Mute Push-button a second time

or adjusting the volume control will un-mute the

MAC7200.

How to Operate the MAC7200, con't Headphones Jack Connect a pair of dynamic headphones to the Headphone Jack with a 1/4" (0.635cm) stereo phone type plug for private listening. The default setting is for Output Connections 1 and 2 to automatically mute. For additional Information refer to "HEADPHONE HXD" on page 31.
Note: The Headphone Output is optimized for impedances ranging from 100 to 600 ohms.
Power Output Meters The MAC7200 Power Output Meters indicate the power delivered to the Loudspeakers. Refer to figure 98. The meters respond to all the musical information
Figure 98
being produced by the Amplifier. They indicate to an accuracy of at least 95% of the power output with only a single cycle of a 2,000Hz tone burst.

Power Guard During normal operation, the Front Panel Power Guard Indicators will momentarily illuminate during peaks in the audio signals. In the event the MAC7200 over heats, due to improper ventilation, high ambient temperature and/or impedance mismatch, the internal protection circuits will activate. The Front Panel Power Guard Indicators will continuously illuminate and the audio will be muted. When the MAC7200 has returned to a safe operating temperature, normal operation will resume.
Using a Separate Power Amplifier There are two different ways to use a separate power amplifier with a MAC7200. The first way is to use the separate amplifier instead of the MAC7200 built-in Power Amplifier. Connect the Loudspeakers to the separate Power Amplifier and remove the McIntosh Jumpers that are located between the OUTPUTS 1 Jacks and the PWR AMP INPUT Jacks. Refer to figure 99.
Note: The McIntosh Jumpers must be connected, between the above mentioned jacks, when the MAC7200 Internal Power Amplifier is to be used.

USB

DSD256

35%

Figure 70 32

Jumpers Figure 99
The second way is to use both a separate Power Amplifier and the MAC7200 built-in Power Amplifier. Connect one pair of Loudspeakers to the separate Power Amplifier and the second pair to the MAC7200. Refer to the MAC7200 Output Connection Diagrams located on the separate folded sheet "Mc2B" and figure 100.
Note: The MAC7200 VOLUME Control will affect the sound level of all the Loudspeakers.
Jumpers Removed Figure 100
Using Output 2 The MAC7200 has provisions for connecting an external Power Amplifier (to drive Loudspeakers in another room) and an external sensor for remote operation of the MAC7200 from that room. With an external Power Amplifier connected (as illustrated on the McIntosh Connection Diagram separate sheet "Mc2B"), press the Front Panel OUTPUT 2 Push-button or press on the Remote Control, the BLUE (Setup) Push-button followed by pressing the OUTPUT 2 Push-button to switch On or Off the external Power Amplifier.

How to Operate the MAC7200, con't

Passthru When the MAC7200 is connected together with a McIntosh Multichannel A/V Control Center or Surround Decoder and has the PASSTHRU Mode activated, it will automatically turn-on when the A/V Processor or Surround Decoder is turned On. It will indicate on the Front Panel Display "PASSTHRU". Refer to figure 101.
PASSTHRU

Figure 101
The MAC7200 OUTPUT 1 / OUTPUT 2 Front Panel Push-buttons are active when in the Passthru Mode. The other Front Panel Controls and Push-buttons are deactivated as long as the Passthru Mode is active.

Optical and Coaxial Digital Inputs When a Digital Input (Optical or Coaxial Connection) on the MAC7200 is selected, the Front Panel Display will indicate the sample rate when a signal is present "48kHz". Refer to figure 102.

COAX 1 48kHz

30%

Figure 102

During the time there is no Digital Signal present on the selected input the display will indicate "______". Refer to figure 103.

COAX 1

______
Figure 103

30%

Operating the FM and AM Tuner
The MAC7200 Tuner provides the ability to select and listen to AM and FM Radio Stations.
The Front Panel Controls labeled TUNING and PRESET allow the selection of either FM or AM Radio Stations. The Front Panel INPUT/TRIM Control, along with various push-buttons on the Remote Control provide access to various Tuner Operational Functions. Refer to figures 70 and 73.
The Front Panel Information Display indicates the Station Preset, Radio Station Frequency, Stereo/Mono (on FM Stations), Signal Strength, Tuning Method, Station Text, FM Signal Information. Refer to figures 104 thru 107.
P1 91.5 MHz ST |||
Figure 104
TUNER CONTROL Manual
Figure 105
91.5 MHz ST ||| Jazz Hits Today.....
Figure 106
91.5 MHz ST ¦ Mpath:¦¦¦ Noise:¦¦¦
Figure 107
AM or FM Band Selection Rotate the MAC7200 Front Panel INPUT Control to select either TUNER FM or TUNER AM. Refer to figure70. The AM, FM or BAND Push-buttons on the Remote Control may also be used to select the desired Broadcast Band. Refer to figure 108.

Default Station Tuning The default Station Tuning Mode for the MAC7200 is Manual. Manual Tuning is accomplished by using either the Front Panel TUNING Control or the UpS or DownT Directional Pushbuttons on the Remote Control. Refer to figures 70 and 108.
Seek Tuning Type The MAC7200 second form of Tuning Types is Seek Tuning. Seek Tuning automatically finds the next available Radio Station. To change from Manual Tuning to Seek Tuning activate the TRIM Mode using the Front Panel Controls or the Remote Control. Select TRIM Mode "TUNER CONTROL, Manual" and then select "TUNER CONTROL, Seek". Refer to figures 105 and 109.
TUNER CONTROL Seek
Figure 109
There are three ways to use Seek Tuning. The first way is to use the Front Panel TUNING Control, by momentarily rotating it a few degrees clockwise or counter-clockwise. The second way is to use the UpS or DownT Directional Push-buttons on the

Figure 108 33

Operating the FM and AM Tuner, con't Remote Control. The third way is to use the Seek or Push-buttons on the Remote Control. Refer to figure 70 and 108 on the previous pages.
Direct Access Tuning The fourth Tuning way is to use the Direct Access Method for FM and AM Stations. This is performed by entering the Radio Station Frequency by using the numeric Push-buttons on the Remote Control. Refer to figure 108. For example, tuning to FM Station 105.7MHz press the following Push-buttons:
Number One, Number Zero, Number Five and Number Seven.
Preset Tuning The MAC7200 allows for presetting 20 AM and 20 FM Radio Stations into memory for rapid recall. Refer to figure 108. CREATE A PRESET Perform the following steps: 1. Tune to the desired FM Station (or AM Station).
Refer to Figure 110.
91.5 MHz ST |||
Figure 110
2. Press the large PRESET Push-button (located between the AM and FM Push-buttons) on the Remote Control and the letter "P" will appear flashing on the left side of the Front Panel Display. Refer to Figure 111.
P 91.5 MHz ST |||
Figure 111
34

3. Using the Remote Control Numeric Push-buttons enter the desired Preset Number. Refer to Figure 112. P1 91.5 MHz ST |||
Figure 112
4. Press the large PRESET Push-button to complete the process of entering Preset One. The "P1" on the Front Panel Information Display will stop flashing. Refer to Figure 113.
P1 91.5 MHz ST |||
Figure 113
ERASE A PRESET Perform the following steps: 1. Use the Remote Control PRESET , PRESET
Push-buttons or the Front Panel PRESET Control to select the desired FM Station Preset (or AM Station Preset) to be erased. Refer to Figure 113. 2. Press the large PRESET Push-button (located between the AM and FM Push-buttons) on the Remote Control, "P1" will disappear and the letter "P" will appear flashing on the left side of the Front Panel Display. Refer to Figure 111. 3. Press the large PRESET Push-button a second time to complete the process of erasing Preset One. The Front Panel Information Display will now just indicate the Frequency, Mode and Signal Strength. Refer to Figure 110.
Note: If it is desirable to remove all 20 Presets (FM and/or AM Stations) refer to Setup "DELETING PRESETS" on page 25
SELECTING A PRESET There are several ways to scan thru available FM or

AM Preset Stations. Rotate the Front Panel PRESET Control Clockwise or Counterclockwise to find the desired station. The second way is to use the Remote Control PRESET , PRESET Push-buttons. The third way is using the Remote Control to direct access the desired Preset Number. First press the large PRESET Push-button, then use the numeric Push-buttons to enter the Preset Number followed by pressing the large PRESET Push-button a second time.
Tuner Text Select the TRIM Tuner Text Mode using the Front Panel Controls or Remote Control. The defaut TRIM Tuner Mode is "Station Info" which indicates whatever a given Radio Station wants to display. Refer to figure 106 on page 33. The second option is to display the RF Multipath1 Signal and Noise Background of the tuned in FM Station or the Signal Strength of the tuned in AM Station. Refer to figure 107 on page 33. The third option is to switch Off the second line of the Front Panel Information Display.
1 Refer to "General Information" number 8 for addition information about RF Multipath Signals.

Figure 108

How to Operate the MAC7200, con't

USB Input Operation and Driver Installation The MAC7200 USB Input provides the capability to playback music from a computer, when the computer is connected to the rear panel USB connector.
Note: The USB Input is for direct connection to a computer only. To playback music from an USB Drive, connect the USB Drive to another USB Port on the computer and select the USB Drive with the Media Playback Program.
The MAC7200 USB Input is compatible with PC Computers using Microsoft®, Windows 7 (SP1), Windows 8.1 and Windows 10. It is also compatible with Apple® Macintosh® Computers using OS-10.6.8 or later.
When using a PC Computer with Windows, a special McIntosh USB Audio Software Driver needs to be installed on the PC Computer. The driver needs to be installed before connecting the MAC7200 USB Input to the USB Port on the computer.
Note: If an Apple Macintosh computer is used with the
MAC7200, no additional driver is required. The McIntosh USB Audio Windows Driver is available for download from the McIntosh Web Site:
http://www.mcintoshlabs.com/us/Support/Pages/ Manuals.aspx
Under "PRODUCT CATEGORY" select "Preamplifiers" then under "MODEL NUMBER" select "MAC7200". Click on "SEARCH" then select "McIntosh-HD USB Audio Windows Drive D v1.0" and download the PC Windows Driver. Follow the instructions below to install the McIntosh MAC7200 Driver:

Requirements: 1. A PC Computer with a functioning USB Port.
2. Windows 7 (SP1 or greater), Windows 8 (8.1) or Windows 10 Operating System.
3. An USB Cable with Type A to Type B Connectors.
Installing the Software It is important to first install the downloaded software on your computer before connecting the McIntosh Product to the computer. The USB Driver is included in the downloaded software package.
Note: Before installing this software, please check to see if the McIntosh Product(s) with the USB-Digital Audio Input has the latest firmware version, if not update the firmware first.
1. Unzip the downloaded McIntosh Windows USB Driver Software Package.
2. Run "McIntoshHDSwPkg_20150814_v1p9p110p2. zip". Refer to figures 114 thru 121.

Figure 114

Figure 115

Purpose: To Install the McIntosh USB Audio Windows Driver for use with McIntosh Products with an USB-Digital Audio Input.

Figure 116

Figure 117

Figure 118

Figure 119

Figure 120

Figure 121

3. When the Windows Security window appears

check the Always trust software from "Savitech

Corp." box and then the Install button. When the

software has been installed, it is neces-

sary to reboot the computer. Refer to

figure 122.

After rebooting, a McIntosh-HD icon will appear on the desktop. Refer to figure 98. Figure 122

USB Connection

Connect the USB Cable with Type A to Type B con-

nectors between the PC Computer and the McIntosh

Product with the USB-Digital Audio Input. An Icon

will appear On-Screen indicating Windows has found

new hardware. Refer to

figure 123.

Upon completion of in-

Figure 123

stalling the driver, figure

124 will appear.

Figure 124

How to Operate the MAC7200, con't

Windows Sound Settings

For proper operation of the McIntosh Product via the

Computer USB Connection, it is required to make

changes to Windows Sound Settings:

1. From the Windows

START button, click on

"CONTROL PANEL"

followed by selecting

"SOUND". Refer to

figure 125.

2. Referring to figure 126,

first select "McIntosh-

HD HS USB Audio" and than click on the "Set

Figure 125

Default" button.

Notes: 1. When the McIn-

tosh USB Audio

Product is not

connected to

your computer,

the previous

default Audio

Device will be

selected. 2. If other McIn-

Figure 126

tosh Products with USB Audio Connections

are also connected to the computer, an ad-

ditional "McIntosh USB Audio" playback

device will appear in the listing. Make

sure to select the "McIntosh-HD HS USB

Audio" from available playback devices

listed when using this McIntosh Product

for USB Audio.

Control Panel Settings To activate the McIntosh-HD USB Audio Control Panel Click on the "McIntosh Icon" (located in the Windows notification area on the right side of the taskbar)

or Click on the Windows "Show hidden icons", then

Select the "McIntosh Icon". Refer to figures 127 and

128.

Notes: 1. It is not necessary

for the McIntosh-

HD USB Audio

Control Panel to

be running, unless

it is desired to

make changes to the default set-

Figure 127

tings.

2. The McIntosh-

HD USB Audio

Control Panel

displays the cur-

rent Sampling

Rate, Bit-Rate

and Buffer Size

for the music

streaming from

the com-

puter into the

MAC7200.

3. When the Media

Stream Program

on the computer

is set to output

in the "ASIO"

format, the Mc-

Intosh -HD USB

Audio Control

Panel allows for

changing the settings parameters

Figure 128

on the fly.

USB Music Playback When the USB Input is selected on the McIntosh MAC7200, the Front Panel Display indicates the

Sampling Rate (refer to figures 129 and 130 for PCM Signals).

USB

46%

44.1kHz

Figure 129

USB

51%

352.8kHz

Figure 130

Figures 131 and 132 indicate a Sampling Rate of 128 or 256 times the Sampling Rate of a CD Disc for the

incoming DSD Digital Audio Signal.

USB

DSD128
Figure 131

46%

USB

51%

DSD256

Figure 132

The Sampling Rate and the Bit Rate are determined

by the original recording, the Application Output

Format (when available) and the McIntosh-HD Control

Panel Settings.

Note: In general, when the original music is recorded at a higher Sampling Rate, the result is usually more detail in the music. However, this higher

rate results in consuming larger amounts of storage space. The Sample Rate usually should be set to match the Sample Rate of the music recording

being played back.

There are many third party Applications (besides Ap-

plications like Windows Media Player) for steaming

music from the computer to McIntosh MAC7200 USB

Input. An example of just one of the available applica-

tions is "JRiver Media Center".

MAC7200 Amplifier Specifications

Amplifier Specifications

Power Output 200 watts is the minimum sine wave continuous average power output per channel, both channels operating
Output Load Impedance 2, 4 or 8 ohms
Rated Power Band 20Hz to 20,000Hz
Total Harmonic Distortion 0.005% maximum with both channels operating from 250 milliwatts to rated power, 20Hz to 20,000Hz
Intermodulation Distortion 0.005% maximum, if the instantaneous peak power is 400 watts or less per channel with both channels operating for any combination of frequencies from 20Hz to 20,000Hz

Sensitivity (for rated output) High Level, 250mV unbalanced, 500mV balanced Phono MM, 2.5mV Phono MC, 0.25mV Power Amp In, 1.4V
Signal To Noise Ratio (A-Weighted) High Level, 95dB below rated output Phono MM, 82dB below 5mV input Phono MC, 80dB below 0.5mV input Power Amplifier, 113dB below rated output
Input Impedance High Level, 20K ohms Phono MM - 47K ohms; 50pF Phono MC - 50, 100, 200, 400 or 1,000 ohms; 100pF
Preamplifier Output Impedance 220 ohms

Maximum Input Signal, con't Phono MC, 8mV Power Amplifier In, 16V
Preamplifier Output Impedance 220 ohms
Headphone Impedance 100 to 600 ohms
Voltage Gain High Level to Output 1 and 2: 15dB Phono MM to Rec Output: 40dB Phono MC to Rec Output: 60dB Phono MM to Output 1 and 2: 55dB Phono MC to Output 1 and 2: 75dB Power Amplifier: 29dB
Power Control and Trigger Output 12VDC, 25mA

Dynamic Headroom 2.0dB

Maximum Input Signal High Level, 8V unbalanced, 16V balanced Phono MM, 80mV

Wide Band Damping Factor Greater than 40

MAC7200 Tone Control Curves

+12
Power Guard

Less than 2% THD with up to 16dB overdrive at

1,000Hz

dB 0

Frequency Response

+0, -0.5dB from 20Hz to 20,000Hz

-6

+0, -3dB from 10Hz to 100,000Hz
-12

Preamplifier Output 1 and 2 (for rated input)

1.4V unbalanced (8V Maximun)

100

200

500

10k

20k

Digital Audio Specifications Digital Input Signal Format Coaxial and Optical Inputs - SPDIF (PCM) MCT and USB Inputs - PCM, DSD
Digital Input Sample Rate Coaxial and Optical: 44.1kHz to 192kHz, 24-Bit MCT: 44.1kHz, 16-Bit (CD)
DSD64 (SACD) USB: 44.1kHz to 384kHz, 32-Bit (PCM)
DSD64, DSD128, DSD256, DXD352.8kHz, DXD384kHz
Digital Inputs Coaxial: 0.5V p-p/75 ohms Optical: -15dbm to -21dbm (TOS Link) MCT: 0.5V p-p/75 ohms USB: USB Type B Connector Tuner FM Specifications
Tuning Range 87.5MHz - 108.0MHz (Europe) 87.9MHz - 107.9MHz (USA) 76MHz - 90MHz (Japan)
FM Channel Spacing 200kHz (USA, Japan) 50kHz (Europe)
Antenna Input 75 Ohms, Type "F" Coax connector
Useable Sensitivity 2.2uV (18.1dBf)
50dB Quieting Sensitivity 1.5uV (14.8dBf)
38

Tuner FM Specifications, con't Signal To Noise Ratio Mono: 70dB Stereo: 68dB
Frequency Response ±1dB 20 to 15,000Hz
Harmonic Distortion Mono: 0.4% Stereo: 0.8%
Channel Selectivity 60dB Adjacent Channel 66dB Alternate Channel
Stereo Separation 38dB Tuner AM Specifications
AM Tuning Range 522kHz - 1602kHz (Europe) 530kHz - 1710kHz (USA) 522kHz - 1611kHz (Japan)
AM Channel Spacing 10kHz (USA) 9kHz (Europe, Japan)
Sensitivity 350uV/m
Signal To Noise Ratio 50dB
Frequency Response 0dB, -6dB 50Hz to 3,000Hz

MAC7200 Digital Audio and General Specifications
Tuner AM Specifications, con't Harmonic Distortion 0.5%
Selectivity 45dB Adjacent Channel
General Specifications Power Requirements Field AC Voltage conversion of the MAC7200 is not possible. The MAC7200 is factory configured for one of the following AC Voltages: 100 Volts, 50/60Hz at 5.2 amps 110 Volts, 50/60Hz at 4.4 amps 120 Volts, 50/60Hz at 4.4 amps 220 Volts, 50/60Hz at 2.45 amps 230 Volts, 50/60Hz at 2.35 amps 240 Volts, 50/60Hz at 2.25 amps Standby: Less than 0.25 watt
Note: Refer to the rear panel of the MAC7200 for the correct voltage.
Overall Dimensions Width is 17-1/2 inches (44.45cm) Height is 7-5/8 inches (19.37cm) including feet Depth is 22 inches (55.88cm) including the Front Panel, Knobs and Cables
Weight 75 pounds (34.1 kg) net, 93 pounds (42.3 kg) in shipping carton
Shipping Carton Dimensions Width is 29-1/2 inches (74.93cm) Depth is 29 inches (73.66cm) Height is 17 inches (43.18cm)

Packing Instructions
In the event it is necessary to repack the equipment for shipment, the equipment must be packed exactly as shown below. It is very important that the four plastic feet are attached to the bottom of the equipment. Two #10 x 2-1/2 inch screws and washers must be used to fasten the unit securely to the bottom pad and wood skid. This will ensure the proper equipment location on the bottom pad. Failure to do this will result in shipping damage. Use the original shipping carton and interior parts only if they are all in good serviceable condition. If a shipping carton or any of the interior part(s) are needed, please call or write Customer Service Department of McIntosh Laboratory. Refer to page 2. Please see the Part List for the correct part numbers.

MAC7200 Packing Material List

Quantity Part Number Description

1 033888

Shipping carton

4 033887

End Cap

1 033697 1 033725 1 034576 1 034480 2 017218 2 401204
2 404033 4 017937 4 400159 4 404080

Inner carton Top pad Bottom pad Wood skid Plastic foot (spacer) #10 x 2-1/2 inch wood screw #10 flat washer 1-3/4 inch Plastic foot #10-32 x 3/4 machine screw #10 flat washer

Packing Instructions

McIntosh Laboratory, Inc. 2 Chambers Street
Binghamton, NY 13903 www.mcintoshlabs.com
The continuous improvement of its products is the policy of McIntosh Laboratory Incorporated who reserve the right to improve design without notice. Printed in the U.S.A.
McIntosh Part No. 04177700

DIGITAL AUDIO INPUTS for components with Digital Optical and Coaxial Outputs sending digital audio signals

MAC7200 Rear Panel Connections

USB DIGITAL AUDIO INPUT for connection to a computer

DATA PORTS send signals to Source Components to allow control with the MA7200 Remote Control

75 OHM FM ANT (Antenna) connects to an external FM Antenna or cable

POWER CONTROL OUTPUTS TRIGger 1 and 2 send turn On/Off signals to assignable components

MCT DIGITAL AUDIO INPUT for streaming high bandwidth digital signals from SACD/CD Transport Components

SERVICE PORT for service use only

RAA2 AM ANT (Antenna) connector allows the supplied McIntosh AM Remote Antenna to be connected

IR INput for signals from a compatible IR Room Sensor

POWER CONTROL MAIN OUTPUT sends turn On/Off signals to a McIntosh Component when the MA7200 is switched On/Off

Right OUTPUT connections for a 2, 4 or 8 ohm Loudspeaker

Left OUTPUT connections for a 2, 4 or 8 ohm Loudspeaker

Connect the MAC7200 power cord to a live AC outlet. Refer to information on the back panel of your MAC7200 to determine the correct voltage for your unit

JUMPER PLUGS connect the Preamplifier OUTPUT 1 Jacks to the PWR AMP INPUTS Jacks and are required for normal operation

UNBALANCED INPUTS 1 thru 5 accept high level program source signals

PHONO MC accepts the low level signals from a Moving Coil Phono Cartridge

RS232 connector1 for connection to a computer or other control device

Main Fuse holder, refer to information on the back panel of your MAC7200 to determine the correct fuse size and rating

OUTPUTS 2 send signals to Power Amplifiers and are switched On/Off with the Front Panel Output 2 Push-Button or Remote Control Push-Button

PWR AMP INPUTS accept signals from the internal Preamplifier or a separate external Preamplifier

GND terminal accepts a ground wire from a turntable

McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549 Part No. 04177900

PHONO MM accepts signals from a Moving Magnet Phono Cartridge

POWER CONTROL PASSTHRU INPUT receives turn On/Off signals from an Audio/ Video Control Center

BALANCED INPUTS accept high level program source signals

1 Refer to page 4 of the MAC7200 Owner's Manual for addition cable information.

MAC7200 Input and Control Connection Diagram

Note: Refer to the MAC7200 Owner's Manual page 10 for additional connection information.

Connection Legend:

Data Cable*-

Digital Signal Cable -

Sensor/Keypad Cable -

RS232 Cable -

Power Control Cable* -

Ground Wire -

Audio Signal Cable -

AC Power Cords -

Video Signal Cable -

Loudspeaker Cable -

RF Signal Cable -

* 2 conductor shielded with 1/8 inch stereo mini phone plug on each end.

FM Antenna

Media Server

SACD/CD Transport

Digital Audio Player
WLAN ANT 1

WLAN ANT 2

Turntable

McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549 Part No. 04177800

RAA2 AM Antenna
IR Sensor Computer

MAC7200 Output and Loudspeaker Connection Diagram

Note: Refer to the MA7200 Owner's Manual pages 10 thru 12 for additional connection information.

Connection Legend:

Data Cable*-

Digital Signal Cable -

Sensor/Keypad Cable -

RS232 Cable -

Power Control Cable* -

Ground Wire -

Audio Signal Cable -

AC Power Cords -

Video Signal Cable -

Loudspeaker Cable -

RF Signal Cable -

* 2 conductor shielded with 1/8 inch stereo mini phone plug on each end.

Right Loudspeaker - Secondary Room

Right Loudspeaker

Connect to AC Outlet

Power Amplifier - Secondary Room
%%
Connect to AC Outlet

Left Loudspeaker - Secondary Room
+
Left Loudspeaker
-+

Input Assignment Chart

Input Type
Unbalanced
Unbalanced
Unbalanced
Unbalanced
Unbalanced
Balanced
MM (Moving Magnet)
MC (Moving Coil) Digital Audio
Input Digital Audio
Input Digital Audio
Input Digital Audio
Input Digital Audio
Input Digital Audio
Input

MAC7200 DEFAULT SETTINGS

Input

Data

Number

Name

Port

1 UNBALANCED (L & R)

UNBAL 1

All (1 thru 4)

2 UNBALANCED (L & R)

UNBAL 2

All (1 thru 4)

3 UNBALANCED (L & R)

UNBAL 3

All (1 thru 4)

4 UNBALANCED (L & R)

UNBAL 4

All (1 thru 4)

5 UNBALANCED (L & R)

UNBAL 5

All (1 thru 4)

BALANCED (L & R)

BAL

All (1 thru 4)

MM (L & R)

MM PHONO

- - - - -

MC (L & R)

MC PHONO

- - - - -

USB

- - - - -

MCT

All (1 thru 4)

1 OPTICAL

OPTI 1

All (1 thru 4)

2 OPTICAL

OPTI 2

All (1 thru 4)

1 COAXIAL

COAX 1 All (1 thru 4)

2 COAXIAL

COAX 2 All (1 thru 4)

Power Control
Main Main Main Main Main Main Main Main Main Main Main Main Main Main

CONNECTION EXAMPLE SETTINGS

Input

Data

Power

Number

Name

Port

Control

1 UNBALANCED (L & R)

2 UNBALANCED (L & R)

3 UNBALANCED (L & R)

4 UNBALANCED (L & R)

5 UNBALANCED (L & R)

BALANCED (L & R)

Media Server

Main

MM (L & R)

- - - - -

MC (L & R)

Turntable

- - - - -

Main

USB

Computer

- - - - -

MCT 1 OPTICAL

SACD/CD Transport
Digital Audio Player

2 - - - - -

Main Main

2 OPTICAL

1 COAXIAL

2 COAXIAL

McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549 Part No. 04178000

Input Assignment Chart

MAC7200 DEFAULT SETTINGS

Input Number

Input Name

Data Port

1 UNBALANCED (L & R)

UNBAL 1

All (1 thru 4)

2 UNBALANCED (L & R)

UNBAL 2

All (1 thru 4)

3 UNBALANCED (L & R)

UNBAL 3

All (1 thru 4)

4 UNBALANCED (L & R)

UNBAL 4

All (1 thru 4)

5 UNBALANCED (L & R)

UNBAL 5

All (1 thru 4)

BALANCED (L & R)

BAL

All (1 thru 4)

MM (L & R)

MM PHONO

- - - - -

MC (L & R)

MC PHONO

- - - - -

USB

- - - - -

MCT

All (1 thru 4)

1 OPTICAL

OPTI 1

All (1 thru 4)

2 OPTICAL

OPTI 2

All (1 thru 4)

1 COAXIAL

COAX 1 All (1 thru 4)

2 COAXIAL

COAX 2 All (1 thru 4)

Power Control
Main Main Main Main Main Main Main Main Main Main Main Main Main Main

NEW ASSIGNED SETTINGS

Input Number

Input Name

Data Port

1 UNBALANCED (L & R)

2 UNBALANCED (L & R)

3 UNBALANCED (L & R)

4 UNBALANCED (L & R)

5 UNBALANCED (L & R)

BALANCED (L & R)

MM (L & R)

- - - - -

MC (L & R)

- - - - -

USB

- - - - -

MCT

1 OPTICAL

2 OPTICAL

1 COAXIAL

2 COAXIAL

Power Control
- - - - -

McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549

Important Additional Operation Information Guide

Safety Instructions

ATTENTION:
RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR

Lithium

Batteries

Disposal Instructions

McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 www.mcintoshlabs.com

TKHOLJKWQLQJÀDVKZLWKDUURZKHDGZLWKLQDQHTXLODWHUDOWULDQJOHLVLQWHQGHGWRDOHUWWKHXVHUWRWKHSUHVHQFHRIXQLQVXODWHG ³GDQJHURXVYROWDJH´ZLWKLQWKHSURGXFW¶VHQFORVXUHWKDWPD\EH RIVXI¿FLHQWPDJQLWXGHWRFRQVWLWXWHDULVNRIHOHFWULFVKRFNWR SHUVRQV
WARNING: TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE.

ATTENTION:
RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

7KHH[FODPDWLRQSRLQWZLWKLQDQHTXLODWHUDOWULDQJOHLVLQWHQGHGWRDOHUWWKHXVHUWRWKHSUHVHQFHRILPSRUWDQWRSHUDWLQJDQG PDLQWHQDQFHVHUYLFLQJLQVWUXFWLRQVLQWKHOLWHUDWXUHDFFRPSDQ\LQJWKHDSSOLDQFH
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK. NO USER-SER-
VICEABLE PARTS INSIDE.

$GGLWLRQDO6DIHW\,QIRUPDWLRQVSHFL¿FWRWKLVSURGXFWPD\EH contained in the Owner's Manual supplied with this product

IMPORTANT SAFETY INSTRUCTIONS!
PLEASE READ THEM BEFORE OPERATING THIS EQUIPMENT.
1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install
in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other appaUDWXVLQFOXGLQJDPSOL¿HUVWKDWSURGXFHKHDW 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the proYLGHGSOXJGRHVQRW¿WLQWR\RXURXWOHWFRQVXOW an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 2QO\XVHDWWDFKPHQWVDFFHVVRULHVVSHFL¿HGE\ the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or WDEOHVSHFL¿HGE\WKHPDQXIDFWXUHU or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.
5HIHUDOOVHUYLFLQJWRTXDOL¿HGVHUYLFHSHUVRQnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. Do not expose this apparatus to dripping or VSODVKLQJDQGWKDWQRREMHFWV¿OOHGZLWKOLTuids, such as vases, should not be placed on the equipment. Ne pas exposer cet appareil à des éclaboussures ou gouttelettes d'un liquide. Aucun objet remplie de liquide comme par exemple un vase ne doit être placé sur l'appareil.
16. If this equipment is supplied with a power supply cord only, the mains plug of the power supply cord shall remain readily operable. To completely disconnect this apparatus from the a.c. mains disconnect the plug from the a.c. receptacle. Si l'équipement est uniquement alimenté par XQFRUGRQG¶DOLPHQWDWLRQOD¿FKHGXFRUGRQ d'alimentation doit demeurer aisément accessible. Pour déconnecter complètement l'équipement du réseau d'alimentation, déconnecter OD¿FKHGXFRUGRQG¶DOLPHQWDWLRQGHODSULVH murale.
17. If this equipment is supplied with AC /DC Adapter with separate power supply cord or the AC/DC Adapter plugging directly into an a.c. receptacle, they shall remain readily operable. To completely disconnect this equipment from

the a.c. mains remove the AC /DC Adapter mains power supply cord from the a.c. receptacle or remove the AC /DC Adapter when it is directly plugged into the a.c. receptacle. Si l'équipement est alimenté par un adaptateur AC/DC munis d'un cordon d'alimentation ou un adaptateur AC/DC qui est alimenté directement à la prise murale, ils doivent demeurer aisément accessibles. Pour déconnecter complètement l'équipement du réseau d'alimentation, déconnecter l'adaptateur AC/DC de la prise murale ou déconnecter le cordon d'alimentation de l'adaptateur AC/DC de la prise murale. 18. WARNING: Do not expose batteries or battery SDFNWRH[FHVVLYHKHDWVXFKDVVXQVKLQH¿UHRU the like. AVERTISSEMENT: Les batteries ou bloc de batteries ne doivent pas etre exposees a une chaleur excessive telle que celle du soleil, feu ou autre source de chaleur similaire. 19. CAUTION: danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. ATTENTION: danger d'explosion si la pile n'est pas remplacée correctement. Ne remplacer que par le même type ou un type équivalent. 20. Connect mains power supply cord only to a mains socket outlet with a protective earthing connection. 21. Warning: The Ethernet connector of this equipment must not be directly connected to a public network. Connection is to be made only by way of a modem or router approved for this purpose.

FCC INFORMATION )RU86DQG&DQDGD&XVWRPHUV
a) User Information acc. to FCC15.21 as following: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
b) Statement for Class B digital device acc. to FCC 15.105 as following: NOTE: This equipment has been tested and found to comply with the limits for a Class A/B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit di erent from that to which the receiver is connected. --Consult the dealer or an experienced radio/ TV technician for help. --This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
c) The device must be kept more than 20 cm from all persons.

Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charge. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with reguards to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, and size of ground conductors, location of antenna-discharge unit, connection to ground electrodes and requirements for the grounding electrode.
([DPSOHRIDQWHQQDJURXQGLQJDV SHU1DWLRQDO(OHFWULFDO&RGH ANSI/NFPA 70

Lithium Battery, Types, Removal and Installation

Lithium Battery
WARNING:
DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD
This product and/or the remote control supplied with this product may contain a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and/or remote control and keep it away from children. If you think batteries might have been swallowed or placed inside of the body, seek immediate medical attention.
AVERTISSEMENT:
NE PAS INGÉRER L'ACCUMULATEUR, 5,648('(%5/85(&+,0,48(
[La telecommande fournie avec] Ce product contient un accumulateur bouton. En cas d' ingestion, l' accumulateur bouton, peut causer des brulures internes severes en a peine 2 heures qui peuvent etre mortelles. Conserver les accumulateurs neufs usages hors de portee des enfants. Sile compartiment de l' accumulateur ne se ferme pas de maniere sure, ne plus utiliser le produit et et le tenir hors de portee des enfants. Encas de soupcon d'ingestion d'un accumulater ou d'introduction dans une partie quelconque du corps, demander immediatement un avis medical.
CAUTION: 'DQJHURIH[SORVLRQLIWKHEDWWHU\LV incorrectly installed. Only install one of the approved Lithium Batteries listed EHORZ
ATTENTION: Danger d'explosion si la pile n'set pas remplacée correctement. Installer uniquement l'une des piles au lithium approuvées énumérées ci dessous.
Lithium Battery Type
Long Life Lithium Coin Cell type battery is used in this product and/or supplied remote control. This product and/or supplied remote control may be supplied with a battery depending on the country where this product is purchased. When purchasing a battery for use in this product and/or remote control, refer to the following list:

Approved Lithium Batteries

Brand

IEC No.

ANSI/NEDA No.

Energizer CR2032

5004LC1

Panasonic &53$%1 5004LC1 1CR Lithium Coin Cells contain Perchlorate - special handling may
apply. For additional information go to https://www.dtsc.ca.gov/ hazardouswaste/perchlorate/

Battery Removal or Installation
It is advisable to remove the Lithium Battery from this product and/or remote control when it is not used for an extended period of time. This will help to extend battery life and avoid possible damage to the product and/or remote control.

BATTERY REMOVAL: Perform the following steps to remove the battery from the product and/or remote control: %HIRUHUHPRYLQJWKH/LWKLXP%DWWHU\¿UVWGLVFRQ-
nect the AC Power Cord and/or AC/DC Adapter from this product.
Note: Step 1 is not required when removing the Lithium
Battery from a remote control. 2. Press the tab and lift up on the Backup Battery Cov-
HUDQGWHPSRUDULO\SODFHLWDVLGH5HIHUWR¿JXUHV and 2. 3. When removing the battery from a remote control proceed to step 4. To remove the battery from a product proceed to step 5. 4. Refering to figure 3, press on the bottom edge of the battery to release the battery from the molded battery socket. Then remove the battery from inside of the Remote Control. Proceed to step 6. 5HIHULQJWR¿JXUHXVHDVPDOOSRFNHWVL]HVFUHZ GULYHURURWKHUVXLWDEOHWRRODQGFDUHIXOO\LQVHUWWKH tip of the tool between the metal tab of the battery socket and the left side of the battery. Then rotate the tool to release the battery from the socket. Remove the battery from inside of the product. 6. Reinstall the Battery Cover. 7. Store the battery in a cool dry place for future use or dispose of the battery in accordance with the local regulations for lithium battery disposal. Batteries should never be thrown away or incinerated.

BATTERY INSTALLATION: Perform the following steps to install the battery into the product and/or remote control: %HIRUHLQVWDOOLQJWKH/LWKLXP%DWWHU\¿UVWGLVFRQ-
nect the AC Power Cord and/or AC/DC Adapter from this product.
Note: Step 8 is not required when installing the Lithium
Battery into a remote control.

9. Press the tab and lift up on the Backup Battery CovHUDQGWHPSRUDULO\SODFHLWDVLGH5HIHUWR¿JXUHV and 2.
10. When installing the battery into the remote control proceed to step 11. To install the battery into a product proceed to step 12.
11. Orient the battery so the + symbol (engraved into RQHVLGHRIWKHEDWWHU\LVIDFLQJXS5HIHUWRILJXUH 7. Then insert the battery into the socket. Make sure the battery is touching both contact points and is seated in the socket. Refer to figure 8.
12. Orient the battery so the + symbol (engraved into RQHVLGHRIWKHEDWWHU\LVIDFLQJXS5HIHUWRILJures 5 and 6. Then insert the battery into the socket. Make sure the battery is touching both contact points and is seated in the socket.
13. Reinstall the Battery Cover.

TAB
Figure 1

LIFT UP
Figure 2

Figure 3
Battery Socket
Figure 5
Battery
R203 CR2032
3V
Figure 7

C C

2 2

CR2032 3V

Figure 4

CR2032 3V

Tabs

Figure 6
Contact Points
R203
Figure 8

Disposal Instructions
North American Waste of Electrical and Electronic Equipment Directive
:KHQGLVFDUGLQJWKHXQLWFRPSO\ZLWKORFDOUXOHVRU UHJXODWLRQV%DWWHULHVVKRXOGQHYHUEHWKURZQ DZD\RULQFLQHUDWHGEXWGLVSRVHGRILQDFFRUGDQFHZLWKWKHORFDOUHJXODWLRQVFRQFHUQLQJ EDWWHU\GLVSRVDO

Waste and Disposal Instructions 3

Disposal Instructions, con't

Waste and Disposal Instructions, con't 4

McIntosh Laboratory, Inc. 2 Chambers Street
Binghamton, NY 13903 www.mcintoshlabs.com
McIntosh Part No. 04170900

MAC7200s t e r e o r e c e i v e r
With 200 Watts per channel, 14 inputs and a highperformance AM/FM tuner, the MAC7200 Stereo Receiver is a music lover's dream.
Built-in AM/FM tuner will pick up your favorite radio stations with unparalleled clarity and a realism that is free from noise and distortion.
All digital inputs are housed in the DA1 Digital Audio Module. The DA1 can be replaced by future modules to easily keep the MAC7200 current with all the latest digital audio technologies.
Supports high resolution digital music up to DSD256 and DXD 384kHz via an 8-channel, 32-bit/192kHz DAC used in Quad Balanced mode.
Features our new McIntosh Monogrammed HeatsinksTM that are so ef cient at dissipating heat that they warrant bearing the McIntosh "Mc" logo.
Utilizes new, more powerful control microprocessors and some of the latest audio-grade circuit components.
Full of numerous McIntosh technologies including Autoformers, Power Guard®, Sentry MonitorTM, Home Theater PassThru, High Drive headphone ampli er with Headphone Crossfeed Director (HXD®) and Power Control.
A Music Lover's Dream

www.mcintoshlabs.com

MAC7200s t e r e o r e c e i v e r

Power Output: 200 Watts per channel. McIntosh Autoformers ensure all speakers receive the full 200 Watts regardless if they are 2, 4 or 8 Ohm impedance.
Total Harmonic Distortion: 0.005% maximum from 20Hz to 20kHz
Tone Controls: Bass and Treble
Headphone Amplifier: 1/4" High Drive with Headphone Crossfeed
Director (HXD®). Powers all headphones from 20 to 600 Ohms.

Analog Inputs: 5 Unbalanced
1 Balanced 1 Moving Coil 1 Moving Magnet
Digital Inputs: 2 Coax 2 Optical 1 USB
1 MCT (used with McIntosh MCT series SACD/CD Transports)
All are housed in DA1 Digital Audio Module.

Tuner Section: Features the same AM/FM performance as a stand alone McIntosh tuner. 20 presets available each for band. Includes remote AM antenna for the nest AM reception.
Home Theater PassThru: Allows for seamless interfacing with a
Home Theater system.
Overall Dimensions (W x H x D): 17-1/2" (44.5cm) x 7-5/8" (19.37cm)
x 22" (55.88cm) including knobs, connectors and cables

Weight: 75 lbs (34.1kg) net, 93 lbs (42.3kg) in shipping carton
For the Consumer's Protection: In order to ensure the highest level of customer satisfaction, new McIntosh products may only be purchased from an Authorized McIntosh Dealer; and, with certain limited exceptions may only be
purchased over-the-counter or delivered and installed by the Authorized McIntosh Dealer. McIntosh does not warrant, in any way, products that are purchased from anyone who is not an Authorized McIntosh Dealer, or that have had their
serial numbers altered or defaced.

Companion Products The MCD350 SACD/CD Player, MCT450 SACD/CD Transport, MT5 Precision Turntable, MB100 Media Bridge, MB50 Streaming Audio Player and XR50 Bookshelf Loudspeakers are logical companions for the MAC7200 Stereo Receiver. Your Authorized Dealer can provide additional information on other McIntosh product combinations.
To learn more, please call us at 1.800.538.6576.
35106700

www.mcintoshlabs.com

HOME ELECTRONICS

THREE YEAR LIMITED WARRANTY

Welcome to the family of McIntosh owners. This is the Warranty for your new McIntosh Home Electronic Product (the "Product"). Your Product has been designed to give many years of trouble-free performance. Nonetheless, failures do sometimes occur even with equipment as well-built as McIntosh's. Therefore, please read this Warranty carefully, because it contains rights, as well as limitations, exclusions, and obligations, which in the event of such a failure may be very important to you. If after reading it thoroughly, you have any questions about the Warranty, please do not hesitate to write or telephone McIntosh at the address or phone number shown on the back of this warranty. Please note that this is the only Warranty which

McIntosh provides for your Product, and that no one, including your dealer, has any authority to either modify or expand upon this Warranty. If your dealer has offered or made any warranties or representations concerning the Product which differ from those contained in this Warranty, they are strictly between you and the dealer, and will neither be binding upon McIntosh nor change any of the provisions in this Warranty. Please also note, that if your Product ever does require Warranty service, obtaining such service will be much easier if you have completed and returned the enclosed Warranty Registration Card. So please take a PLQXWHWR¿OORXWDQGUHWXUQWKH5HJLVWUDWLRQ&DUG now, before you become too distracted by the great sounds coming from your new McIntosh Product!

04166700

Scope and Duration of Warranty
Subject to the terms and conditions stated below, McIntosh Laboratory, Inc. ("McIntosh") warrants to the original owner that this Product shall be free from defects in workmanship or materials for a term of three (3) years from the date when it was purchased from an Authorized McIntosh Dealer. Provided, however, that rather than the three (3) years of coverage afforded the Product generally, where applicable, vacuum tubes contained in our Products are warranted for 90 days from the date of purchase, hard disc drives and projector lamps contained in our Products are warranted for one (1) year from the date of purchase.
Limitations on Persons and Products Covered by this Warranty
This Warranty and all rights provided here under are limited to the original owner. In the event that the original owner transfers ownership of the Product prior to expiration of the three-(3) year term, this Warranty shall terminate in its entirety upon the date of such transfer. In addition, McIntosh does not warrant in any way Products which are purchased from anyone who is not an Authorized McIntosh Dealer, or which have had their Serial Numbers altered or defaced. Therefore this Warranty is void and inapplicable if this Product has been purchased from someone other than an Authorized McIntosh Dealer, or has had its original Serial Numbers altered or defaced.
Geographical Limitations
This Warranty has been included with a McIntosh Product that is designed, intended to be sold and used only within the United States and Canada. Accordingly, this Warranty only applies to Products which are purchased in the United States or Canada, and only applies while such Products are used in the United States or Canada. Products purchased outside the United States or Canada, and failures occurring outside the United States or Canada, are not covered by this Warranty.
What McIntosh will do under the Warranty
In the event of any defect covered by this Warranty, McIntosh shall without charge provide all parts, PDWHULDOVDQGODERUQHFHVVDU\WRUHVWRUHWKH3URGXFWWRLWVRULJLQDOVSHFL¿FDWLRQV$IWHUUHSDLU0F,QWRVK shall return the Product to its owner at the owner's expense. In the alternative, McIntosh may at its sole option either replace the Product without charge, or if replacement is not commercially practicable or repair or replacement cannot be accomplished within a reasonable time, McIntosh may refund the purchase price of the Product, subject where appropriate to reasonable depreciation for actual use in accordance with applicable laws, in full satisfaction of its warranty obligations. McIntosh or its Authorized Service Agency will undertake to complete the repair and return of the Product as soon as circumstances permit, unless prevented by causes beyond their reasonable control.
Limitations on McIntosh's Obligations under the Warranty
McIntosh's sole Obligation under this Warranty shall be to repair or replace the Product, or at its option refund the purchase price, as provided for hereinabove. McIntosh does not warrant against, nor shall it be liable for, any of the following: removal or installation charges; shipping expenses either to or from McIntosh or its Authorized Service Agency; loss of use; property damage of any kind; or other incidental or consequential damages or losses of any kind.
Note: Some states do not allow exclusion or limitation of consequential damages, so the foregoing exclusions may not apply to you.

Parts and Occurrences that are not Covered by the Warranty
This Warranty does not cover any of the following: (a) glass panels, cabinetry, trim, or other appearance items (except where they are defective at the time of original sale and the Product is delivered for UHSDLU ZLWKLQ WKH ¿UVW WKLUW\ GD\V WKHUHDIWHU E EDWWHULHV RU GDPDJH WR WKH 3URGXFW FDXVHG E\ failure of batteries; (c) or damage to the Product caused by failure of projector lamp; (d) loss of, or GDPDJH RU FRUUXSWLRQ WR GLJLWDO GDWD ¿OHV RU RWKHU LQIRUPDWLRQ FRQWHQW RI DQ\ NLQG UHJDUGOHVV RI cause; (e) failures arising from accident, catastrophe, misuse, neglect, or failure to properly connect and operate the Product in accordance with the accompanying instructions; (f) failures arising from improper installation or removal of the Product; or (g) failures arising from any tampering, alteration, or damage to the Product or attempted servicing of the Product by anyone other than McIntosh or an Authorized McIntosh Service Agency; and McIntosh shall have no liability or obligation of any kind with respect to any of the foregoing types of failures.
What the Owner must do to obtain service under this Warranty
To obtain service under this Warranty, the owner must at the owner's expense arrange for any necessary de-installation of the Product, and deliver or ship the Product to McIntosh at the address below, or to an Authorized McIntosh Service Agency, properly packaged, prepaid, and insured at the owner's expense. In addition, the owner must provide evidence that the Product is at the time of delivery within the scope of his Warranty, by either having completed and submitted to McIntosh on a timely basis the accompanying Warranty Registration Card, or by including the original sales receipt (photocopies are not acceptable) with the Product when it is delivered for repair.
What the Owner must Pay For
As noted above, the owner must pay any expense of removing the Product from its installation, and must pay any expenses for delivery of the Product to McIntosh or the Authorized McIntosh Service Agency. Upon return of the Product to the owner following repair, it shall be the owner's responsibility to pay for the shipping charges incurred in return of the Product, as well as to arrange and pay for any re-installation which may be required. In addition, it shall be the owner's obligation to pay for any repairs made to any Product for which the owner has neither completed and submitted the Warranty Registration Card at the time of purchase nor included the original sales receipt with the Product when delivered for service, at McIntosh's or its Authorized Service Agency's then-current repair rates.
How to learn where the nearest Authorized McIntosh Service Agency is, or obtain answers to other questions concerning this Warranty
In order to learn the name and address of the nearest Authorized McIntosh Service Agency, obtain instructions for shipment of a covered Product to McIntosh, or obtain the answers to any other questions you may have concerning this Warranty, you may telephone McIntosh's Customer Service Department between the hours of 9:00 a.m. and 4:30 p.m. Eastern Time, Monday through Friday, at 888-979-3737 (607-723-3512) or write to McIntosh at 2 Chambers Street, Binghamton, New York 13903-2699, Attention: Customer Service Department or visit the "Contact Us" area of the McIntosh Web Site at www.mcintoshlabs.com.
1RWH7KLV:DUUDQW\JLYHV\RXVSHFL¿FOHJDOULJKWVDQG\RXPD\DOVRKDYHRWKHUULJKWVZKLFKYDU\ from state to state.

References

McIntosh - Page Not Found

Acrobat Distiller 10.1.16 (Windows)