Axial SCX24 Jeep Wrangler JL 1/24 Scale Electric 4WD Ready-to-Run

Important Information

NOTE: All instructions, warranties, and other warranty documents are subject to the sole discretion of Horizon Hobby, LLC. For the most up-to-date product literature, please visit www.horizonhobby.com or www.towerhobbies.com and click on the support tab for this product.

Meaning of Specific Terms

The following terms are used throughout the manual to indicate different levels of danger when using this product:

• WARNING: Procedures which, if not followed correctly, can result in serious property damage and serious injury OR result in a high probability of superficial injury.
• CAUTION: Procedures which, if not followed correctly, can result in property damage AND serious injury.
• NOTE: Procedures which, if not followed correctly, can result in property damage AND possibly a slight risk of injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating it. Incorrect operation of the product can result in damage to the product and property, and serious personal injury. This is a sophisticated hobby product. It must be operated with caution and common sense and requires basic mechanical ability. Any irresponsible use of this product that fails to adhere to the safety principles may result in personal injury, property damage, and product damage. This product is not intended for use by children without the direct supervision of an adult. Do not attempt to disassemble the product, use it with incompatible components, or make performance upgrades without the approval of Horizon Hobby, LLC. This manual contains instructions for safety, operation, and maintenance. It is crucial to read and follow all instructions and warnings in the manual before assembly, setup, and operation, in order to correctly operate the vehicle and avoid any property damage or serious injury.

Ages 14 and up. This is not a toy.

Safety Precautions and Warnings

As the user of this product, it is your sole responsibility to operate it in a manner that does not endanger yourself or others, or cause damage to the product or to the property of others. This model is controlled by a radio signal, which may be subject to interference from many sources outside your control. This interference can cause a momentary loss of control. It is therefore recommended to maintain a safe distance around your model, which will help avoid collisions or injuries.

• Never operate your model when the transmitter batteries are low.
• Always operate your model in a clear area, away from cars, traffic, or people.
• Never, for any reason, operate your model in the street or in populated areas.
• Strictly follow the instructions and warnings for this and any optional/complementary equipment (chargers, rechargeable battery packs, etc.) you use.
• Keep all chemicals, small parts, and electronic components out of reach of children.
• Never lick or place any part of your model in your mouth to avoid the risk of serious injury or death.
• Exercise caution when using tools and sharp instruments.
• Exercise caution during assembly, as some parts may have sharp edges.
• After using your model, DO NOT touch certain parts such as the motor, electronic speed controller, and battery, as they may still be at high temperatures. You risk severe burns if you come into contact with them.
• Do not place your fingers or any other object between rotating or moving parts, as this could cause damage or serious injury.
• Always turn on your transmitter before turning on the vehicle's receiver. Always turn off the receiver before turning off your transmitter.
• Ensure that the model's wheels are not in contact with the ground when you are testing your radio equipment.

Table of Contents

This section lists the contents of the manual, which are covered in the following HTML structure.

Waterproof Vehicle with Waterproof Electronic Components

Your new Horizon Hobby vehicle has been designed and manufactured by combining waterproof and water-resistant components, allowing you to use this product in various "Wet Conditions," including puddles, streams, wet grass, snow, and even rain. Although the vehicle has high water resistance, it is not completely waterproof, and your vehicle should NOT be used as a submarine. The various electronic components installed on the vehicle, such as the electronic speed controller (ESC), servo(s), and receiver, are waterproof. However, most mechanical components are resistant to water spray but should not be submerged. Metal parts such as bearings, suspension shafts, screws, nuts, and electrical connector contacts are exposed to oxidation if additional maintenance is not performed after use in wet conditions. To maintain your vehicle's performance and warranty long-term, the procedures described in the "Maintenance in Wet Conditions" section must be performed regularly if you drive in wet conditions. If you do not wish to perform the required additional maintenance, you should not use the vehicle in these conditions.

CAUTION: Failure to exercise care during operation and failure to follow the following instructions may result in product malfunction and/or void the warranty.

General Precautions

• Read the maintenance procedures for wet conditions carefully and ensure you have all the necessary tools to maintain the vehicle.
• Not all batteries can be used in wet conditions. Consult your battery manufacturer's documentation before use. Precautions must be taken when using Li-Po batteries in wet conditions.
• Most transmitters are not resistant to water spray. Consult your transmitter's manual or manufacturer before use.
• Never operate your transmitter or vehicle during a storm.
• NEVER use your vehicle where it could come into contact with saltwater (seawater or road salt water), or polluted or contaminated water.
• A small amount of water can reduce the motor's lifespan if it is not certified waterproof or splash-resistant. If the motor becomes excessively wet, apply light throttle to expel as much water as possible from the motor. Running a wet motor at high speed will cause rapid damage.
• Operation in wet conditions can reduce the motor's lifespan. Water resistance causes increased strain. Adjust the gear ratio by using a smaller pinion or a larger spur gear. This will increase torque (and motor life) when driving in mud, deep puddles, or any other wet condition, increasing the load on the motor.

Maintenance in Wet Conditions

To maintain your vehicle after driving in wet conditions:

• Drain water collected by the tires by spinning them at high speed. Remove the body, turn the vehicle upside down, and give short bursts of full throttle until water is expelled.
• CAUTION: Always keep hands, fingers, tools, or other loose/hanging objects away from rotating parts.
• Remove the battery and dry its contacts. If you have an air compressor or compressed air can, blow out any moisture from the connector.
• Remove the vehicle's wheels and rinse them with a spray bottle to remove mud and dirt. Avoid rinsing the bearings and drivetrain.
• NOTE: Never use a high-pressure cleaner to clean the vehicle.
• Use an air compressor or compressed air can to dry the vehicle and help remove water trapped in crevices and corners.
• Spray lubricant or moisture displacer on bearings, screws, or other metal parts. Do not spray on the motor.
• Allow the vehicle to dry before storing it. Water (and oil) may continue to drip for several hours.
• Increase the frequency of inspection, disassembly, and lubrication of the following components:
  • Wheel shafts and bearings of the front and rear spindles.
  • All drivetrain cases, gears, and differentials.
  • Motor: Clean it with motor cleaner spray and lubricate the bearings with bearing lubricant.

Contents of the Box

Vehicle Dimensions: Length: 200mm, Width: 98mm, Height: 120.7mm, Operational Weight: 160g

Warnings Regarding USB Charging

WARNING: Lack of caution during the use of this product and failure to comply with the following warnings may result in product malfunction, electrical problems, excessive heat, FIRE, and ultimately, personal injury and property damage.

• NEVER LEAVE BATTERIES CHARGING UNATTENDED.
• NEVER CHARGE BATTERIES OVERNIGHT.
• Never attempt to charge dead, damaged, or wet battery packs.
• Never attempt to charge a battery pack containing different types of batteries.
• Never allow children under 14 years of age to charge battery packs.
• Never charge batteries in extremely hot or cold locations, and do not expose them to direct sunlight.
• Never charge a battery if the cable is pinched or short-circuited.
• Never plug in the charger if the power cable has been pinched or short-circuited.
• Never attempt to disassemble the charger or use a damaged charger.
• Always use only rechargeable batteries designed for use with this type of charger.
• Always inspect the battery before charging.
• Always keep the battery away from materials that may be affected by heat.
• Always monitor the charging area and keep a fire extinguisher available.
• Always stop the charging process if the battery becomes hot to the touch or begins to deform (swell).
• Always connect the positive (+) and negative (–) cables correctly.
• Always disconnect the battery after charging and allow the charger to cool between charges.
• Always charge in a well-ventilated area.
• Always interrupt all processes and contact Horizon Hobby if the product malfunctions.
• Only charge rechargeable batteries. If you charge non-rechargeable batteries, they could explode and cause personal injury and/or property damage.
• The USB port will be installed near the equipment and will be easily accessible.

CAUTION: Always ensure that the charged battery complies with the specifications of this charger. Otherwise, it may cause excessive heat and other associated product malfunctions, which can cause personal injury or property damage to the user. Please contact Horizon Hobby or an authorized dealer for compatibility questions.

CAUTION: If, at any time during charging, the battery pack becomes hot or begins to swell, immediately disconnect the battery and stop the charging process, as batteries can cause fire, collateral damage, and injury.

Charging the Vehicle Battery

1. Plug the charger into a suitable USB power port. The charger works with most 5V mobile power sources or smartphone chargers, with a minimum output of one amp.

   NOTE: Charging the battery from a USB power port with an output less than 1 amp may generate heat.

2. Connect the charger cable to the battery, observing correct polarity. It takes approximately 45 to 60 minutes to charge a completely empty battery. Charging times may vary depending on the power source.
3. Disconnect the battery from the charger once the charging cycle is complete.
4. Unplug the charger from its power source.

CAUTION: Once charging is complete, immediately disconnect the battery. Never leave a battery connected to the charger.

CHARGER LED INDICATIONS:

• Solid RED = Charging
• Solid RED; Flashing GREEN = Standby
• Solid GREEN = Charge complete

Transmitter Layout

Use the diagram below to familiarize yourself with the different parts of your transmitter. The transmitter's antenna is internally mounted and located in the front of the transmitter. When driving your model, hold the transmitter so it is oriented as vertically as possible. Do not try to follow your model with the transmitter. This provides the best RF signal between the transmitter and receiver. Do not cover the front of the transmitter during use, as this will block the RF signal, causing a loss of control.

Controls:

• Steering Wheel: Turn left or right to steer the vehicle.
• Throttle Control: Pull forward to accelerate, push backward to reverse.
• Steering Trim: Adjust so the vehicle drives straight without any steering input from the wheel.
• Throttle Trim Button: Adjusts the throttle control rate.
• Dual Rate Steering: Adjusts the total steering throw.
• Bind Button: Used for binding the transmitter to the receiver.
• Power Switch: Turns the transmitter on/off.
• Battery Level Indicator: Solid RED: Battery voltage is good. Flashing RED: Battery voltage is critically low (below 4V). Replace transmitter batteries.
• LED Control: On/Off/Flashing.

Installing Transmitter Batteries

1. Press the battery compartment latch and rotate the battery cover to open.
2. Install 4 AA alkaline batteries (or Ni-Cd or Ni-MH), checking for correct polarity.
3. Close the battery cover until it latches.

CAUTION: NEVER remove transmitter batteries while the vehicle is powered on. This can lead to loss of vehicle control and personal or property damage.

CAUTION: If using rechargeable batteries, only charge rechargeable batteries. Charging non-rechargeable batteries may cause them to explode and result in personal injury or property damage.

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to national and local regulations.

Removing the Vehicle Body

To remove the body, typically clips or fasteners hold it in place. Refer to the diagrams for specific removal steps.

[Diagram description: An illustration showing the vehicle chassis with the body being lifted off, indicating how it is attached and removed.]

Installing the Vehicle Battery

Insert the charged battery into the vehicle's battery compartment, ensuring correct connection and polarity.

[Diagram description: An illustration showing the vehicle chassis and the battery pack being inserted into its designated compartment, with a close-up of the connector.]

Turning on the Transmitter

Locate the power switch on the transmitter and move it to the "ON" position.

[Diagram description: An illustration of the transmitter with the power switch highlighted in the "ON" position.]

Turning on the Vehicle

Locate the vehicle's power switch or connector and turn it on.

[Diagram description: An illustration showing the vehicle chassis with the power switch or connector highlighted.]

Testing the Controls

With the vehicle's wheels off the ground, test the throttle and steering controls. Ensure the wheels turn in the correct direction and that the front wheels steer correctly with steering input.

After verifying that the control directions are correct, begin driving slowly. If the vehicle does not drive straight without steering input, adjust the steering trim knob on the transmitter until the vehicle drives straight without steering input.

Enjoy driving your vehicle!

[Diagram description: An illustration showing the transmitter being held and used to control the vehicle, with arrows indicating steering and throttle actions. Another illustration shows the vehicle's wheels turning.]

After Driving

When you have finished driving your vehicle:

1. Turn off the vehicle.
2. Turn off the transmitter.
3. Remove the vehicle battery and charge it if necessary.

Transmitter and Receiver Binding

Binding is the process of programming the receiver to recognize a specific transmitter signal, thereby preventing interference from other transmitters. The transmitter and receiver included with your vehicle are factory-bound. If you need to re-bind them, follow the instructions below.

NOTE: Do not attempt to bind the transmitter and receiver if other compatible transmitters are in bind mode within approximately 120m (400ft). This action could result in an unintended bind to the wrong transmitter and loss of control of your vehicle.

Before starting the binding procedure, ensure that the servos and motor are connected to the correct ports on the receiver, and that charged batteries have been installed in the transmitter. Always place the transmitter in bind mode first, followed by the receiver.

1. Turn on the transmitter while holding down the bind button. The G LED will flash rapidly.
2. Release the bind button.
3. Turn on the receiver. The receiver will enter bind mode after approximately one second.

When binding is successful, the receiver LED will illuminate solid, and the transmitter's G LED will turn off.

[Diagram description: An illustration showing the transmitter with the Bind button highlighted. Another illustration shows the receiver board with connection ports and an LED.]

Troubleshooting Guide

Parts List

Warranty and Repairs

Warranty Period: Exclusive Warranty - Horizon Hobby, LLC (Horizon) warrants that the purchased Product ("Product") will be free from material and workmanship defects at the date of purchase by the Buyer. The warranty period corresponds to the legal provisions of the country where the product was acquired. The warranty period is 6 months, and the warranty obligation period is 18 months from the expiration of the warranty period.

Warranty Limitations:

• (a) The warranty is granted to the original buyer ("Buyer") and is not transferable. The Buyer's recourse consists of repair or exchange under this warranty. The warranty applies only to products purchased from an authorized Horizon dealer. Sales to third parties are not covered by this warranty. Warranty claims will be accepted upon valid proof of purchase. Horizon reserves the right to modify the provisions of this warranty without prior notice, thereby revoking existing warranty provisions.
• (b) Horizon makes no warranty regarding the product's merchantability or the user's fitness and capability for a particular use. It is the Buyer's sole responsibility to verify if the product meets their capabilities and intended use.
• (c) Buyer's Recourse – It is at Horizon's sole discretion to determine if a product with a warranty claim will be repaired or exchanged. These are the exclusive remedies for the Buyer when a defect is found. Horizon reserves the right to inspect all components used and potentially integrated into the warranty case. The decision to repair or replace the product is solely Horizon's. The warranty excludes aesthetic defects or defects caused by force majeure, incorrect product handling, incorrect or commercial use of the product, or modifications of any kind. The warranty does not cover damage resulting from incorrect assembly or handling, accidents, or operation, as well as attempts at maintenance or repair not performed by Horizon. Returns made by the Buyer directly to Horizon or its national representatives require written confirmation.

Limitation of Damages: Horizon shall not be liable for direct or indirect consequential damages, loss of revenue, or commercial losses, in any way related to the product, regardless of whether recourse is sought under contract, warranty, or warranty obligation. Furthermore, Horizon will not accept recourse from a warranty case where such recourse exceeds the unit value of the product. Horizon has no influence over the assembly, use, or maintenance of the product, or over any product combinations chosen by the Buyer. Horizon assumes no warranty and accepts no recourse for injuries or damages resulting therefrom. Horizon Hobby shall not be liable for use that does not comply with applicable laws, rules, or regulations.

By using and assembling the product, the Buyer accepts all warranty provisions contained herein without restriction or reservation. If, as the Buyer, you are not prepared to accept these provisions in relation to the product's use, please return the complete, unused product in its original packaging to the seller.

Safety Information: This is a sophisticated hobby product, not a toy. It must be used with caution and common sense and requires basic mechanical and mental skills. Failure to use the product safely and reasonably may result in injury and significant property damage. This product is not intended for use by children without adult supervision. The instruction manual contains safety information as well as maintenance and operation instructions. It is absolutely essential to read and understand these instructions before first use. Only then will it be possible to avoid incorrect handling and accidents leading to injury and damage. Horizon Hobby shall not be liable for use that does not comply with applicable laws, rules, or regulations.

Questions, Assistance, and Repairs: Your local specialized dealer and point of sale cannot provide an estimate of warranty eligibility without consulting Horizon. This also applies to warranty repairs. In such cases, please contact the dealer who will arrange an appropriate decision with Horizon to assist you as quickly as possible.

Maintenance and Repair: If your product requires maintenance or repair, contact either your specialized dealer or Horizon directly. Pack the product carefully. Please note that the original packaging carton is generally not sufficient to protect the product from damage during transport. Use a courier service that offers tracking and insurance, as Horizon assumes no responsibility for the shipment of the product until its accepted receipt. Please include proof of purchase, a detailed description of the defects, and a list of all distinct items sent. We also require a complete address, a phone number (for inquiries), and an email address.

Warranty and Repairs: Warranty claims will only be processed upon presentation of original proof of purchase from an authorized specialized dealer, showing the buyer's name and date of purchase. If the warranty case is confirmed, the product will be repaired. This decision is solely at Horizon Hobby's discretion.

Paid Repairs: For paid repairs, we will provide an estimate which we will forward to your dealer. The repair will only be carried out after we receive confirmation from the dealer. The repair cost must be paid to the dealer. For paid repairs, we charge a minimum of 30 minutes of workshop labor plus return shipping costs. If no agreement for repair is reached within 90 days, we reserve the right to destroy the product or use it otherwise.

CAUTION: We only perform paid repairs for electronic components and motors. Mechanical repairs, especially for helicopters and radio-controlled cars, are extremely costly and must therefore be performed by the buyer themselves.

Contact Information for Warranty and Repair

IC Information

IC: 25584-N4ZG4P00
IC: 25584-N4ZR4P00
CAN ICES-3 (B)/NMB-3(B)

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

EU Conformity Information

EU Compliance Statement: Axial Jeep Wrangler JL 1/24 Scale Electric 4WD RTR (AXI00002V2T1/T2); Horizon Hobby, LLC hereby declares that this equipment is in compliance with the following directives: Low Voltage Directive 2014/35/EU; EMC Directive 2014/30/EU; Radio Equipment Directive 2014/53/EU; RoHS 2 Directive 2011/65/EU; RoHS 3 - Amending 2011/65/EU Annex II 2015/863. The full text of the EU declaration of conformity is available at the following Internet address: https://www.horizonhobby.com/content/support-render-compliance.

NOTE: This product contains batteries covered by the European Directive 2006/66/EC, which cannot be disposed of with household waste. Please follow local regulations.

Wireless Frequency Range / Wireless Output Power:

• Transmitter: 2405-2450MHz, 15.26dBm
• Receiver: 2405-2450MHz, 15.26dBm

Official EU Manufacturer: Horizon Hobby, LLC, 2904 Research Road, Champaign, IL 61822 USA

Official EU Importer: Horizon Hobby, GmbH, Hanskampring 9, 22885 Barsbüttel Germany

WEEE DIRECTIVE: The label on this equipment complies with European Directive 2012/19/EU on waste electrical and electronic equipment (WEEE). This label indicates that this product must not be disposed of with household waste, but must be deposited in an appropriate facility to allow for its recovery and recycling.

Exploded Views

The following sections provide exploded views of various components of the Axial SCX24 Jeep Wrangler JL. These diagrams illustrate how the parts are assembled and can be used to identify replacement parts.

• AXI31612: SCX24 Shock Set (assembled) - Shows the shock absorbers and their mounting hardware.
• AXI31611 and AXI204000: SCX24 Driveshaft Set (short, medium, long) - Illustrates the driveshafts and their connection points.
• AXI31608: SCX24 Transmission (assembled) - Details the gearbox components, gears, and housing.
• AXI31609: SCX24 Front Axle (assembled) - Shows the front axle assembly, including suspension arms and steering components.
• AXI31610: SCX24 Rear Axle (assembled) - Details the rear axle assembly.
• AXI204000: SCX24 Suspension Links (short, medium, long) - Illustrates the various suspension links used in the chassis.
• AXI201001, AXI201002, AXI31609, AXI204000, AXI31619, AXI31612, AXI31614, AXI31611, DYNB0012, HRZ00015: These part numbers correspond to various chassis, body, suspension, drivetrain, and electronic components shown in assembly diagrams.
• AXI200000: 2019 Jeep JLUCRC Body Set (clear and cut) - Shows the vehicle's body shell and associated mounting hardware.
• AXI31615, AXI31567: These part numbers refer to wheels and tires.

[Note: Detailed textual descriptions of each screw, washer, and gear within the exploded views are omitted for conciseness, focusing on the main component sets.]