Owner's Manual for HEB lighting models including: L2 WT 0 1-10V WiFi RF Push Dimmer, L2 WT, 0 1-10V WiFi RF Push Dimmer, RF Push Dimmer, Push Dimmer, Dimmer
WiFi controller L2(WT) - HEB lighting
User Manual Ver 1.0.0 Page 2 L2(WT) 0/1-10V WiFi RF Push Dimmer 0-10V or 1-10V dimming setting Select 0-10V dimmer or 1-10V dimmer according to dimmable LED driver.
0/1-10V WiFi + RF + Push Dimmer Model No.: L2(WT) 2 channel 0/1-10V signal output/AC relay output/Tuya APP cloud control/Voice control/RF dimming/Push Dim Features WiFi + RF + AC push 0/1-10V dimmer, output 2 channel 0/1-10V signal. High voltage AC input, High voltage AC relay output. LVD Dimming or dual color control selectable by DIP switch. For dual color control, the two channel output can be set as warm white and cool white respectively, or one for brightness adjust and the other for color temperature adjust. 0-10V or 1-10V output selectable by DIP switch. Tuya APP cloud control, support on/off, color temperature and brightness adjust, delay turn on/off light, timer run, scene edit and music play function. Voice control, support amazon ECHO and TmallGenie smart speaker. 256 levels 0-100% dimming smoothly without any flash. Compatibility with RF 2.4G single zone or multiple zone remote control. Each L2(WT) controller can also work as WiFi-RF converter, then use Tuya APP to control one or more RF dimming LED controller or driver synchronously. Connect with external push switch to achieve on/off and 0-100% dimming function. Light on/off fade time 3s selectable. Technical Parameters Input and Output Input voltage Output signal Output current AC100-240V 2 x 0/1-10V 0/1-10V: 20mA/CH AC: Max 3A Dimming data Input signal RF Control distance Dimming level Dimming range Tuya APP + RF + Push Dim 30m(Barrier-free space) 256 levels 0 -100% Safety and EMC EMC standard (EMC) Safety standard(LVD) Radio Equipment(RED) Certification ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4 EN 62368-1:2020+A11:2020 ETSI EN 300 328 V2.2.2 CE,EMC,LVD,RED User Manual Ver 1.0.0 Environment Operation temperature Case temperature (Max.) IP rating Warranty Warranty Ta: -30 OC ~ +55 OC T c: +65OC IP20 5 years Mechanical Structures and Installations AC L input AC N input AC N output AC L output AC Push in 100-240 VAC 100-240VA C 1 A1 A2 Push Switch 100-240 VAC OUT PUT INPUT L2(WT) WiFi 2CH 0/1-10V Dimmer Uin=100-240VAC Iin=100mA max. Uout=2x(0/1-10V)Signal Iout=2x50mA max. AC Out=3A max. Temp range: -30~+55 0.5-2.0mm² 4-5mm DIM WW 1 GND CCT CW 2 GND ON 0-10V ON CCT 1 1-10V 2 DIM MAT CH 0/1-10V OUTPUT O N 12 L2(WT) 0/1-10V WiFi + RF + Push Dimmer Ch1 0/1-10V signal output GND Ch2 0/1-10V signal output GND DIP switch for 0/1-10V or DIM/CCT select Match key 45mm 175mm 160mm Systemwiring 3G/4G/5G WiFi Tuya Cloud 27mm WiFi 15m Mobile Phone WiFi Router L2(WT) 0-10V Dimmable LED Driver LED light Amazon ECHO 30m RFRemote(Optional) L2(WT) L2(WT) 0-10V Dimmable LED Driver LED light 0-10V Dimmable LED Driver LED light ZONE POWER ZONE SCENE ZONE SCENE ZONE SCENE PanelRFRemote(Optional) 30m L2(WT) 0-10V Dimmable LED Driver LED light Wired connection Wireless connection Note: 1.Theabove distance is measured in spacious(noobstacle) environment, Please refer to the actual test distance before installation. 2.PleasecheckiftheWiFi routernetin2.4Gband, the5Gband isnotavailable, and donothideyourrouternetwork. 3. PleasekeepthedistancebetweenL2(WT) devicesandrouterclose, andchecktheWiFisignals. Page 1 Wiring diagram V+ ACN 0/1-10V V- ACL Dimmable Driver DIMDIM+ V+ ACN 0/1-10V V- ACL Dimmable Driver DIMDIM+ + Single color LED strip(CW) + Single color LED strip(WW) 100-240V AC 100-240VAC Push Switch 1 A1 A2 Push Switch 100-240 VAC OUT PUT INPUT L2(WT) WiFi 2CH 0/1-10V Dimmer Uin=100-240VAC Iin=100mA max. Uout=2x(0/1-10V)Signal Iout=2x50mA max. AC Out=3A max. Temp range: -30~+55 0.5-2.0mm² 4-5mm DIM WW 1 GND CCT CW 2 GND ON 0-10V ON CCT 1 1-10V 2 DIM MATCH Note: 1. We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 100 pieces, The maximum length of the wires from dimmer to LED driver should be no more than 50 meters. 2. Switch off the power, then switch on power, repeat again. Immediately short press match key 3 times, the light on/off time will change between 3s and 0.5s. 3. If total power of the 0/1-10V dimming driver is less than 600W, we can use AC OUT port to cut off power input of the driver. 4. When use AC OUT port, an additional AC relay or contactor is needed when total input current of the load is higher than 3A or inrush current is greater than 30A. Push-Dim Function Short press: Turn on or off light. Long press (1-6s): Press and hold to step-less dimming, With every other long press, the light level goes to the opposite direction. Tuya APP network connection and operation Press and hold Match/Set key for 2s, or push twice Match/Set key fastly, Clear previous network connection, enter Smart config mode, the blue LED indicator fast flash. DIM CCT Press and hold Match/Set key for 5s: Clear previous network connection, enter AP config mode, the blue LED indicator fast slow. If smart config failed, please try AP config. If Tuya APP network connection succeed, the blue LED indicator will stop flash, and in Tuya APP, you can find DIM or CCT device. Tuya APP interface operation: DIM: Touch brightness slide to adjust brightness. CCT: Touch color wheel to adjust color temperature. Touch brightness slide to adjust brightness. User Manual Ver 1.0.0 DIM CCT 0/1-10V OUTPUT O N 12 P0-1W0MV ldeutvye(l(%V)) P1-1W0MV ldeutvye(l(%V)) 0-10V or 1-10V dimming setting L2(WT) 0/1-10V WiFi + RF + Push Dimmer Select 0-10V dimmer or 1-10V dimmer according to dimmable LED driver. 0-10V Dimmer 1-10V Dimmer 1100.0 99.0 88.0 77.0 66.0 55.0 44.0 33.0 22.0 11.0 10 20 30 40 50 60 70 80 90 100 Brightness(%) CCT dimming setting ON 0-10V 1 1-10V 1100.0 99.0 88.0 77.0 66.0 55.0 44.0 33.0 22.0 11.0 10 20 30 40 50 60 70 80 90 100 Brightness(%) ON 0-10V 1 1-10V ON CCT Select the DIP Switch 2 ON to set as CCT light type firstly. 2 DIM (When select the DIP Switch 2 OFF to set as DIM light type, Ch1 and Ch2 output is same.) ON 0-10V When power is off, select the DIP switch 1 ON, then press hold the Match key, and power up the dimmer in the same time, the RUN LED indicator will flash two times, 1 1-10V set as Ch1 for for brightness adjust and Ch2 for color temperature adjust. ON 0-10V When power is off, select the DIP switch 1 OFF, then press hold the Match key, and power up the dimmer in the same time, the RUN LED indicator will flash two times, 1 1-10V set as Ch1 for warm white dimming and Ch2 for cool white dimming respectively (factory setting). L2(WT) match RF remote control (Optional) End user can choose the suitable match/delete ways. Two options are offered for selection: Use the L2(WT)'s Match key Use Power Restart Match: Short press match key of L2(WT), immediately press on/off key (single zone remote) or zone key (multiple zone remote) on the remote. Match: Switch off the power of L2(WT), then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote. The light blinks 3 times means match is successful. Delete: Press and hold match key of L1(WT) for 10s to delete all match, The light blinks 5 times means all matched remotes were deleted. .DSwelietcteh: off the power of L2(WT), then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote. The light blinks 5 times means all matched remotes were deleted. L2(WT) work as WiFi-RF converter to match other RF dimming LED controller or driver End user can choose the suitable match/delete ways. Two options are offered for selection: Use the controller's Match key Use Power Restart Match: Short press match key of the controller, immediately press on/off key on the Tuya APP. The LED indicator fast flash a few times means match is successful. Delete: Press and hold match key of the controller for 5s, The LED indicator fast flash a few times means match was deleted. Match: Switch off the power of the controller, then switch on power, repeat again. Immediately short press on/off key 3 times on the Tuya APP. The light blinks 3 times means match is successful. .Delete: Switch off the power of the controller, then switch on power, repeat again. Immediately short press on/off key 5 times on the Tuya APP. The light blinks 5 times means match was deleted. Page 2Corel PDF Engine Version 16.1.0.843