Alessa X-Large Chandelier Assembly Instructions

Notice

This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

Tools Required (Not Included)

• Phillips Screwdriver
• Slotted Screwdriver
• Slip Joint Pliers
• Chain Pliers
• Measuring Tape
• Wire Strippers
• Wire Cutters

Assembly Instructions

Diagram 1: Illustrates the main chandelier components and their assembly order. Key parts labeled include: A (Canopy), B (Mounting Plate), C (Mounting Screws), D (Collar Loop), E (Quick Links), F (Canopy), G (Collar Ring), H (Chain), I (Fixture Loop). Also shows quantities for specific parts: P (5PCS), K (10PCS), L (5PCS), N (10PCS), O (10PCS). Bulbs are noted as not included.

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove collar loop (D) from chain (H) by removing quick link (E).
3. Install mounting plate (B) to the junction box and secure with mounting screws (C).
4. Secure collar loop (D) to mounting plate (B) using pliers to tighten locknut.
5. Install canopy (F) to collar loop (D) and secure with collar ring (G).
6. Determine desired overall length, and amount of chain (H) needed. Shorten chain using chain pliers. (Keep extra chain)
7. Attach chain (H) to collar loop (D) and fixture loop (I) using quick links (E). Secure quick links (E).
8. Thread fixture wire and ground wire through chain (H).
9. Note: When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave about 12" to reach the junction box.
10. Separate two sides of molded wire, and strip insulation on each 5/8".
11. Loosen collar ring (G) and let canopy (F) slip down chain (H) carefully.
12. Twist all fixture wires together and slip through center hole of collar loop (D).
13. Note: Untwist wires and separate to prepare for connection.
14. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Connect fixture ground wire and supply ground wire (usually green or bare copper) using wire nut (A). Note: It is imperative that the fixture is grounded.
15. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A).
16. Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A). Caution: Do not reverse the hot and neutral connections.
17. Make sure all wire connections are tight, then carefully tuck into the junction box.
18. Install canopy (F) to collar loop (D) and secure with collar ring (G).
19. Install light bulbs into the sockets.

Crystal Assembly

Use diagrams 2 & 3 to complete below:

Diagram 2 & 3 Description: Diagram 2 shows crystal stands (L) connecting rings P (top) and Q (middle), and crystal drops (O) connecting ring Q to metal plate R. Diagram 3 shows crystal drops (J & K) attaching to ring P, and crystal drops (N) attaching to ring Q.

1. Hang crystal stands (L) to bottom of ring (P), then hang opposite end to top of middle ring (Q).
2. Hang crystal stands (O) to bottom of ring (Q), then hang opposite end to holes on metal plate (R).
3. Hang crystal drops (J & K) to top of ring (P).
4. Hang crystal drops (N) to bottom of ring (Q).

Care Instructions

Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Certifications/Features: Intertek Listed, Suitable for Damp Locations, LED Compatible.