Bosch GBH 5-40 DCE Rotary Hammer Spare Parts
Model: GBH 5-40 DCE, Type 3 611 B64 001
Figure 1: Exploded View of Rotary Hammer Components
This diagram illustrates the various components of the Bosch GBH 5-40 DCE rotary hammer. Key parts include:
- 2: Motor stator (220V - 240V)
- 4: Trigger switch (on/off)
- 6: Cable guide sleeve (Ø8.7-Ø9.6x66 mm)
- 21: Tool holder protection cap
- 25: Locking pin for hammer tube
- 26: Bushing for SDS-plus tool holder protection cap
- 31: Damping ring
- 51: Angle gear crown
- 79: Screw for guide plate fixing
- 80: Speed variator
- 81: Rear handle
- 94: Priming washer
- 104: O-ring (52.0mm x 2.0mm) for percussion housing
- 117: Needle roller bearing
- 138: Seal for impact unit cover
- 141: Rotor radial seal
- 142: Radial seal for tool holder bushing
- 143: Tool holder spring ring
- 165: O-ring (22x4.0 mm)
- 167: Radial seal
- 168: O-ring (22x3mm) for percussion
- 177: Handle screw
- 803: Armature / Rotor
- 805: Power cable with mains plug
- 811: Carbon brush set
- 817: Carbon brush compression spring
- 830: Support washer for hammer tube
- 856: Pneumatic hammer piston
- 860: Clutch crown gear
- 884: Additional handle
- 890: Special grease for rotary hammer lubrication
- 897: Wear parts maintenance kit
Note: Some parts require Loctite 222 for securing. Please refer to lubrication instructions. Modifications are reserved.
Figure 2: Additional Components and Accessories
This diagram shows additional parts and accessories:
- 87: Ø62mm
- 86: Torque specification (7-11 Nm)
- 85: M8 thread
- 884: Additional handle
- 890: Special grease
- 691: Carrying case
Detailed Parts List
| Part No. | Description | Reference No. |
|---|---|---|
| 2 | Stator moteur 220V - 240V | 1 614 220 123 |
| 4 | Interrupteur gâchette marche / arrêt | 1 617 200 120 |
| 6 | Manchon passe-cable d'alimentation - Ø8,7-Ø9,6x66 mm | |
| 21 | Capuchon de protection porte-outil | 1 610 508 038 |
| 25 | Butée de verrouillage forêt sur tube marteau | 1 612 300 036 |
| 26 | Douille butée pour capuchon de protection de porte-outil SDS-plus | 1 610 290 076 |
| 31 | Bague amortissante | 1 610 290 103 |
| 51 | Couronne d'angle | 1 607 000 E7U |
| 79 | Vis de fixation plaque de guidage | 1 613 435 015 |
| 80 | Variateur de vitesse | 1617 233 047 |
| 81 | Poignée arrière | 1 615 132 088 |
| 94 | Rondelle d'amorçage | 1 610 102 056 |
| 104 | Joint torique 52,0mm x 2,0mm boitier de percussion | 1 610 210 160 |
| 117 | Rouleau à aiguilles | 1 610 913 029 |
| 138 | Joint de couvercle du carter de l'unité de frappe | 1 611 015 053 |
| 141 | Joint radial rotor | 1 610 290 066 |
| 142 | Joint radial pour coussinet de porte-outil | 1 610 290 069 |
| 143 | Bague ressort porte-outil | 1 614 601 021 |
| 165 | Joint torique dimension 22x4,0 mm | 1 610 210 079 |
| 167 | Joint radial | 1 610 283 033 |
| 168 | Joint torique 22x3mm percuteur | 1 610 210 144 |
| 177 | Vis poignée | 1 603 435 051 |
| 803 | Induit / Rotor | 1614 011 098 |
| 805 | Câble d'alimentation avec prise secteur | 1 617 000 723 |
| 811 | Jeu de balais charbon | 1 617 014 144 |
| 817 | Ressort compression balai charbon | 1 614 652 004 |
| 830 | Rondelle d'appui pour tube marteau | 1 617 000 478 |
| 856 | Piston de marteau pneumatique | 1 617 000 A04 |
| 860 | Engrenage couronne d'embrayage | 1 617 000 A37 |
| 884 | Poignée supplémentaire | 1 612 025 055 |
| 890 | Graisse spéciale adaptée pour lubrification perforateurs | |
| 897 | Kit entretien pièces d'usure | 1 617 000 A4L |
If the part you are looking for is not listed or you need further assistance, please contact Bosch customer service.
