Celebrating 100 years of Consumer Electronics | Emerson Radio
Owner's Manual for Emerson models including: CKSW0555 Smartset Clock Radio, CKSW0555, Smartset Clock Radio, Clock Radio, Radio
Emerson Smartset Wireless Charging Alarm Clock Radio Featuring a Large 1.4" Red LED Display and Temperature Sensor, FM Radio, Black : Home & Kitchen
CKSW0555 User Manual (PDF) Emerson Emerson Radio Emerson,CKSW0555,Smartset,Wireless,Charging,Alarm,Clock,Radio,Featuring,a,Large,1.4",Red,LED,Display,and,Temperature,Sensor,FM,Radio,Black,Clock,CKSW0555,B0C1CST5HF,B0BZTJBCVR
File Info : application/pdf, 2 Pages, 4.85MB
DocumentDocumentWith Auto-Time Setting System, Dual Clock Alarm, PLL FM Radio, 4-Level Dimmer, Wireless Charger and Temperature Sensor
CKSW0555
Visit our website at www.emersonradio.com
PRÉCAUTION: Danger d'explosion si les piles sont remplacées de facon incorrect. Remplacer les piles seulement par le méme type de pile ou l'équivalent.
Customer Service Hotline, toll free, at 1-800-898-9020.
Remove any descriptive labels, stickers or protective film on the front or top of the cabinet, if any. Do Not remove any labels or stickers from the back or bottom of the cabinet.
Unwind the line cord connecting the AC adapter. Extend the wire antenna fully and orient it for better FM reception.
Front Panel
1 2 3 4
5
Top Panel
22 21 20
19
18
press and hold display` Flashes'
until the
Release the TIME ZONE button and then press either the TUNE- or TUNE+ button until your own time zone appears on the display, then release the button. The clock display will change to the correct time in the time zone you selected. The clock will always return to the correct time in the zone you selected after every power interruption. If you move to a different time zone, simply change the default zone display to the new zone and the SmartSet® will remember that setting for you.
Checking The Current Year-Date-Day of Week-Time Settings Press the CLOCK SET button repeatedly to see the cycle of year, date, day of week and time. To restore time display mode, leave it idle for few seconds.
Setting The Year the CLOCK SET button until the Year 'Flashes',
Press the TUNE- or TUNE+ button to adjust the Year ('y22'=year 2022 and so on);
the button;
Setting The Date
Press the CLOCK SET button again and release, the Date 'Flashes'; Press the TUNE- or TUNE+ button to adjust
the Month;
8
5 Press the CLOCK SET button again and release,
7
the Date 'Flashes';
6 Press the TUNE- or TUNE+ button to adjust the Date;
Setting The Time
6
7 Press the CLOCK SET button again and release, the Hour 'Flashes'; 8 Press the TUNE- or TUNE+ button to adjust the Hour
(where AM indicator 'On' is AM, 'Off' is PM);
9 Press the CLOCK SET button again and release, the
Minutes 'Flashes';
10 Press the TUNE- or TUNE+ button to adjust the Minutes
11 Press the CLOCK SET button again, or leave it idle for few tens of
seconds, to save all new settings and restore it to time display mode. Note: Time zone and clock settings can only be adjusted in Standby mode, where the FM Radio is disabled.
Daylight Saving Time And Leap Year Adjustments
1.) Read these instructions. 2.) Keep these instructions. 3.) Heed all warnings. 4.) Follow all instructions. 5.) Do not use this apparatus near water. 6.) Clean only with dry cloth. 7.) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8.) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat. 9.) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10.) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11.) Only use attachments / accessories specified by the manufacturer. 12.) Unplug this apparatus during lightning storms or when unused for long periods of time. 13.) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 14.) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 15.) The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus. 16.) Mains plug is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely. 17.) Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same
or equivalent type.
9 10 11 12
3.) AM Indicator ('On'=AM,'Off'=PM) 4.) Wireless Charging Indicator 5.) Battery Compartment (bottom) 6.) 7.) 8 9.) ON/OFF button 10.) VOL-/AL.1 button 11.) VOL+/AL.2 button
13
14 15 16 17
12.) Ambient Temperature button 13.) SNOOZE/DIMMER/SLEEP button 14.) CLOCK SET button
15.) TIME ZONE/MEM./STO. button 16.) TUNE- button 17.) TUNE+ button 18.) Wireless Charging Pad 19.) Speaker (back) 20.) Temperature Sensor (back)
21.) AC Adapter (bottom) 22.) FM Wire Antenna (back)
Leap Year At "12:00 Midnight" on February 28th, the calendar display will change to "2.29".
IMPORTANT NOTES
Turn Daylight Saving Function OFF/ON (in Standby Mode Only) Daylight Saving Time is NOT observed in Hawaii, American Samoa, Guam, Puerto Rico, the Virgin Islands and in, most of Arizona, with exception of the Navajo Indian Reservation in Arizona. If you do not want the clock to adjust itself automatically according to Daylight Saving Time, you can disable it by pressing and holding the TUNE+ (DST start date) or TUNE- (DST end date) button for 5 secs, the display will show `dSt On' DST start or end date accordingly, which means the auto Daylight Saving Time has been enabled (`On' by default). Press the TUNE+ or TUNE- button accordingly to toggle between 'OFF' and 'On' both DST start and end dates. Leave it idle for a few seconds to store your new DST settings and resume to clock mode.
Adjusting The Wake Up Time, Alarm Week Mode And Alarm Volume IMPORTANT: Alarm settings can only be adjusted in Standby mode. Your SmartSet® clock radio has separate alarms that can be set and used independently. You may use the alarms to wake two people at different times, or you may use one alarm for weekdays and the other for weekend wake up times. The procedure for adjusting the wake up times is the same for both Alarm1 and Alarm2. · Press and hold the AL.1(AL.2) button until the display blinks and changes from the current
time to the Alarm1(Alarm2) wake up time. · Release the AL.1(AL.2) button, press the TUNE- or TUNE+ button to adjust Hours. Press
the AL.1(AL.2) button again to confirm, then the Minutes blinks. Press the TUNE- or TUNE+ button to adjust Minutes. · Press the AL.1(AL.2) button again to confirm, then the Alarm Week Mode blinks. Press the AL.1(AL.2) button repeatedly to select your desired Alarm Week Mode: 1-7, 1-5 or 6-7. · Press the AL.1(AL.2) button again to confirm, then the Alarm Volume blinks (only if it is set to wake-to-radio alarm mode). Press the TUNE- or TUNE+ button to select your desired wake-to-radio alarm volume (V01~V16). · Press the AL.1(AL.2) button again to store the alarm setting and resume to clock mode. NOTE: Be sure that you have set the wake up time correctly by observing the AM Indicator. If the AM Indicator is `On' the wake up time is "AM". If the AM Indicator is `Off', the wake up time is "PM". Your SmartSet® clock radio allows you to select from three different Alarm Week Modes for each alarm. They are: 1-7
1-5
6-7
Checking The Wake Up Times (in Standby mode only) To check the Wake Up Time set for Alarm1(Alarm2), press briefly the AL.1(AL.2) button.
Listening To The Radio 1.) Press the ON/OFF button to turn the radio On. The frequency of the tuning
frequency will show for a few seconds on the display. 2.) Set the volume level by pressing the VOL+ or VOL- button to a level that is
neither too high nor too inaudible. 3.) Select your desired radio station/frequency with the TUNING control:
a) Press TUNE+ or TUNE- button briefly, the receiving frequency will increment or decrement by one step.
b) Press and hold the TUNE+ or TUNE- button for two seconds then release. Auto Station Searching will be engaged, the receiving frequency will increment or decrement automatically until a station with acceptable reception is found.
NOTE: The FM antenna is a long wire located at the back. Extend this wire antenna fully and orient it for better FM reception. 4.) Adjust the volume control to the desired setting. 5.) When you finished listening, press the ON/OFF button to turn the radio Off.
Storing And Recalling Radio Station Memory When you have a few favorite radio stations to listen to, you may like to save them, and pick one out of them in a few seconds without needing to search it each time.
Our digital tuning technology PLL (Phase-Lock-Loop) allows you to do this easily
by following steps:
Storing Stations Into Memory 1) Make sure the radio is turned ON.
2) Tune in the desired station with the TUNING control described above.
3) Press and hold the STO. button until `PXX' blinks, where `XX' (01~20) is the programmable memory location.
4) While `PXX' is blinking, press the TUNE- or TUNE+ button to change it to your desired memory location from 01 to 20. For example, `P03' means the current listening station is about to be stored on the 3rd location of the memory.
5) After deciding the memory location, press the STO. button again, the current listening station is then stored accordingly.
6) The display will show the frequency of the station just stored for few seconds and then resume to clock mode.
Recalling Stations From Memory 1) Make sure the radio is ON. 2) Press the MEM. button, `PXX' shows on the display. The station according to
the memory location will be tuned in.
3) While `PXX' is showing on the display, press the TUNE- or TUNE+ button can change the memory location from 1 through 20, and the station stored in that
location will then be tuned in.
4) The display will show the frequency of the station for few seconds and then resume to clock mode.
Wake To RADIO (1 or 2 ) Press the AL.1(AL.2) button repeatedly to turn the 1 (2 ) Indicator On.
2) Press and hold the AL.1(AL.2) button until the display blinks and changes from the current time to the Alarm1 or Alarm2 wake up time.
3) Release the AL.1(AL.2) button, press the TUNE- or TUNE+ button to adjust Hour. Press the AL.1(AL.2) button to confirm, then the Minutes will blink. Press the TUNE- or TUNE+ button to adjust Minutes.
4) Press the AL.1(AL.2) button to confirm, then press the TUNE- or TUNE+ button to select Alarm Week Mode (1-7 everyday, 1-5 weekdays or 6-7 weekends only), if necessary.
5) Press the AL.1(AL.2) button to confirm, then press the VOL- or VOL+ button to adjust the alarm volume level (V01~V16) that will come on at wake up time.
6) Press the AL.1(AL.2) button to confirm and save the alarm settings. 7) At the selected wake up time the radio will turn On and has its radio volume
gradually reaches its preset level. It will play for one hour and then shut Off automatically. 8) To stop the radio sooner, press the ON/OFF button. The radio will stop but the alarm remains set and will turn the radio On again at the same time on the following day (depending on the Alarm Week Mode setting). 9) If you do not want the alarm to turn the radio On the following day, quickly press and release the appropriate ALARM button until alarm indicator light is Off.
(1 or 2 )
Sensing Room Temperature
1 Press the TEMP. button to sense indoor temperature.
Fahrenheit
Celsius
2 Temperature can be converted between
Fahrenheit and Celsius by pressing
and holding the TEMP. button while in
temperature mode.
WARNING: DO NOT place the Temperature Sensor in the mouth or any part NofOthTeEb: oWdyhetonatvhoeidseitnfrsoomr efrxaccetuerdinsgtihnetoospmearall tpinagrtircalensgaen(d3h2a-1rm40in°gFy),oiut.will display as `--F'.
1
2
NOTE: Wake-to-buzzer alarm volume level is fixed and cannot be adjusted.
4.) To stop the buzzer sooner, press the ON/OFF button. The buzzer will stop but the alarm remains set and will turn the buzzer on again at the same time on the following day (depending on the Alarm Week Mode setting).
5.) If you do not want the alarm to turn the radio on the following day, quickly press and release the appropriate ALARM button until the alarm indicator light is off.
Radio And Buzzer Alarm Operation
3.) Turn the radio bottom up and use a small screw driver to remove the screw securing the battery holder to the cabinet.
Snooze/Repeat Alarm
press the
7.) Save these instructions for future use as you will have to do this again.
1) Press the SLEEP button after the radio is turned On. The display will show `10' (10 minutes default). After 10 minutes countdown the radio will shut off automatically. Each time you press the SLEEP button the sleep timer increases in 10 minutes step (10-90, OFF minutes). NOTE: When you change the sleep timer from the 10 minutes default setting to a different setting, the new setting becomes the default setting. Whenever you activate the sleep timer it will begin with your new default setting and count down to zero from that point.
2) To cancel the sleep timer before it counts down to `00' and shut the radio Off immediately, press the ON/OFF button once.
4-Level DIMMER Control Press the DIMMER button while in Standby mode and select any of the four levels.
Saturday
2022 CLOCK SET
Wireless Charging A 5W Wireless Charging Pad is built on top of this unit for wireless power transfer to any Qi-compatible Smartphones or Qi-enabled Receivers over a vertical distance of NOT more than 0.2 inches (5 mm).
1) Place your Qi-compatible smartphone or receiver (only one set at a time) on top of the Wireless Charging Pad. The center of your smartphone or receiver must be positioned properly right at the middle of this charging pad in order to maximize the charging efficiency.
2) While wireless charging started or detected, the indicator will be flashing `Red' slowly.
3) To make sure wireless charging performs properly, check the charging icon
and/or charging message displays on your phone.
4) While your phone is fully charged, the indicator will turn solid `Red'. Please also check the charging icon and/or charging message on your phone to ensure it is fully charged, then remove it from the wireless charging pad.
Note:
Y This wireless charging pad works with Qi-compatible device including
iPhone 14/13/12/11/XS/XR/X/8/8 Plus, Galaxy S22, S21, S20, S10 Plus/S10E/S10/S9 and 5W-15W all Qi-enabled phones.
Y Wireless charging may not work properly if the protective case or
accessory placed at the back of your smartphone is thicker than 0.2 inches (5 mm), remove the protective case or accessory before placing your phone (screen facing upward) on the wireless charging pad.
Y Do not place any foreign objects, such as coins, keys, metallic objects,
magnets, and magnetic stripe cards, between your phone and the wireless charger, to avoid interference or overheating. While wireless charging error occurred, the indicator will be flashing `Red' rapidly to alert user to get the erroneous receiver removed.
1.) Follow the instructions on previous page to install a new CR2032 lithium battery in the battery compartment.
2.) Connect the radio to your AC outlet and let the clock set itself. Follow the instructions on sections Setting the Year/Date/Time to set the clock to the correct year,date and time Press the CLOCK SET button repeatedly to check the year,date and time. Make final adjustment if necessary. 3 to 5
6
CKSW0555
959 Route 46 East Suite 210, 2nd Floor Parsippany, NJ 07054
CKSW0555-20230104-00
Printed in China