User Manual for SuperLightingLED models including: L1, 0 0r 1 10V ZigBee RF Push Dimmer, L1 0 0r 1 10V ZigBee RF Push Dimmer, L1 WZ
N L 100-240 AC IN 0/1-10V OUT- MATCH ON 0-10V 1-10V A1 A2 M d Push Switch VAC User Manual Ver 1.0.1 Page 2 L1(WZ) 0/1-10V ZigBee RF Push Dimmer
N L 100-240 AC IN 0/1-10V OUT- MATCH ON 0-10V 1-10V A1 A2 M d Push Switch VAC User Manual Ver 1.0.5 Page 2 L1(WZ) 0/1-10V ZigBee RF Push Dimmer
pirms 4 dienām — Voice control, support for Amazon Alexa, Google Assistant, Tmall Genieand Xiaodu voice assistant. ○ 0-10V or 1-10V output selectable by DIP switch. ○ 256 levels ...
0/1-10V ZigBee + RF + Push Dimmer Model No.: L1(WZ) Tuya APP cloud control/Philips HUE control/Voice control/RF dimming/Push Dim/0-10V or 1-10V/Wall junction box mounting Features ZigBee + RF + AC push 0/1-10V dimmer, 1 channel output. Output 1 channel 0/1-10V signal, connect with 0/1-10V dimmable driver. Tuya APP cloud control, support on/off, brightness adjust, delay turn on/off light, timer run, scene function. Philips HUE APP control by connect with Philips HUE bridge. Voice control, support amazon ECHO and TmallGenie smart speaker. 0-10V or 1-10V output selectable by DIP switch. 256 levels 0-100% dimming smoothly without any flash. Compatibility with RF 2.4G single zone or multiple zone dimming remote control. Each L1(WZ) controller can also work as ZigBee-RF converter, then use Tuya APP to control one or more RF dimming LED controller or driver synchronously. Connect with external push switch to achieve on/off and 0-100% dimming function. Light on/off fade time 3s selectable. Easy to be placed in standard wall junction box behind a push switch. LVD Technical Parameters Input and Output Input voltage Output signal AC100-240V 0/1-10V (20mA) Safety and EMC EMC standard (EMC) Safety standard(LVD) Radio Equipment(RED) Certification ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4 EN 62368-1:2020+A11:2020 ETSI EN 300 328 V2.2.2 CE,EMC,LVD,RED Dimming data Input signal RF Control distance Dimming level Dimming range Environment Operation temperature Case temperature (Max.) IP rating Tuya APP + RF + Push Dim 30m(Barrier-free space) 256 levels 0 -100% Ta: -30 OC ~ +55 OC T c: +65OC IP20 User Manual Ver 1.0.5 Warranty Warranty 5 years Mechanical Structures and Installations Match key DIP switch for 0-10V or 1-10V select AC Push in 0/1-10V signal output MATCH ON 0-10V 1-10V +- 0/1-10V OUT Push 100-240 Switch VAC A1 A2 AC IN N L GND AC N input AC L input L1(WZ) 0/1-10V ZigBee + RF + Push Dimmer 52.00 mm 26.00 mm 52.00 mm Typical Wall Junction Box Mounting Systemwiring 3G/4G/5G WiFi Tuya Cloud 15m Mobile Phone WiFi Router 15m 15m Tuya ZigBee Gateway L1(WZ) 0-10V Dimmable LED Driver LED light Amazon ECHO 30m RFRemote(Optional) L1(WZ) L1(WZ) 0-10V Dimmable LED Driver LED light 0-10V Dimmable LED Driver LED light ZONE POWER ZONE SCENE ZONE SCENE ZONE SCENE PanelRFRemote(Optional) 30m L1(WZ) 0-10V Dimmable LED Driver Wired connection Wireless connection Note: 1.Theabove distance is measured in spacious(noobstacle) environment, Please refer to the actual test distance before installation. 2.Users must use the Tuya ZigBee gateway to realize remote control and voice control. LED light Page 1 Wiring diagram MAT CH ON 0-10V 1-10V +- 0/1-10V OUT DIM+ ACN 0/1-10V DIM- ACL Dimmable Driver V+ V- + Single color LED strip Push 100-240 Switch VAC A1 A2 AC IN N L Push Switch Push-Dim Function Short press: Turn on or off light. Long press (1-6s): Press and hold to step-less dimming, With every other long press, the light level goes to the opposite direction. AC110-220V Note: 1. We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 50 pieces, The maximum length of the wires from dimmer to LED driver should be no more than 50 meters. 2. Switch off the power, then switch on power, repeat again. Immediately short press match key 3 times, the light on/off time will change between 3s and 0.5s. Tuya APP network connection and operation Press and hold Match/Set key for 2s, reset ZigBeenetwork. Press and hold Match/Set key for 5s, or push twice Match/Set key fastly, Clear previous network connection, enter config mode. the blue LED indicator fast flash. Repeat power on and off for 5 consecutive times, also clear previous network connection, enter config mode. If Tuya APP network connection succeed, the blue LED indicator will stop flash, and in Tuya APP, you can find ZB-DIM device. Tuya APP interface operation: Touch brightness slide to adjust brightness. ZB-DIM User Manual Ver 1.0.5 L1(WZ) 0/1-10V ZigBee + RF + Push Dimmer 0-10V or 1-10V dimming setting Select 0-10V dimmer or 1-10V dimmer according to dimmable LED driver. 0-10V Dimmer 1-10V Dimmer P0-1W0MV ldeutvye(l(%V)) P1-1W0MV ldeutvye(l(%V)) 1100.0 99.0 88.0 77.0 66.0 55.0 44.0 33.0 22.0 11.0 10 20 30 40 50 60 70 80 90 100 Brightness(%) ON 0-10V 1-10V 1100.0 99.0 88.0 77.0 66.0 55.0 44.0 33.0 22.0 11.0 10 20 30 40 50 60 70 80 90 100 Brightness(%) ON 0-10V 1-10V L1(WZ) match RF remote control (Optional) End user can choose the suitable match/delete ways. Two options are offered for selection: Use the L1(WZ)'s Match key Use Power Restart Match: Short press match key of L1(WZ), immediately press on/off key (single zone remote) or zone key (multiple zone remote) on the remote. Match: Switch off the power of L1(WZ), then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote. The light blinks 3 times means match is successful. Delete: Press and hold match key of L1(WZ) for 10s to delete all match, The light blinks 5 times means all matched remotes were deleted. .Delete: Switch off the power of L1(WZ), then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote. The light blinks 5 times means all matched remotes were deleted. L1(WZ) work as ZigBee-RF converter to match other RF dimming LED controller or driver End user can choose the suitable match/delete ways. Two options are offered for selection: Use the controller's Match key Use Power Restart Match: Short press match key of the controller, immediately press on/off key on the Tuya APP. The LED indicator fast flash a few times means match is successful. Delete: Press and hold match key of the controller for 5s, The LED indicator fast flash a few times means match was deleted. Match: Switch off the power of the controller, then switch on power,repeat again. Immediately short press on/off key 3 times on the Tuya APP. The light blinks 3 times means match is successful. .Delete: Switch off the power of the controller, then switch on power, repeat again. Immediately short press on/off key 5 times on the Tuya APP. The light blinks 5 times means match was deleted. Page 2Corel PDF Engine Version 16.1.0.843 CorelDRAW X6