User Manual for INDITECH models including: GSM Intercoms Mobile Network, GSM, Intercoms Mobile Network, Mobile Network, Network
GSM INTERCOM EXTERNAL 24V 125x100
File Info : application/pdf, 8 Pages, 818.15KB
DocumentDocumentUSER MANUAL GSM INTERCOMM SR.NO 1 DETAILS PRODUCT NAME/MODEL NO: 2 PRODUCT DESCRIPTION 3 FEATURES 4 SPECIFICATIONS 5 INSTALLATION AND WIRING STEPS WITH IMAGES/DIAGRAM 6 MOUNTING DETAILS WITH IMAGES/DIAGRAM 7 HOW TO OPERATE 1|Page INTRODUCTION GSM intercoms use the mobile network via a SIM card to allow for an unlimited wireless range, just like your mobile phone. This device is designed for the Elevator systems in case an emergency or fault condition. It gives hands free experience to the user with Mic, Speaker and a Switch for calling. . 1. PRODUCT NAME/MODEL NO: GSM INTERCOMM I s 2|Page 2. PRODUCT DESCRIPTION 3. This product provides an easy and quick response in an emergency condition in elevator systems for the user. This GSM INTERCOM device is installed in control room and antenna is placed at high network area. Speaker, Mic and Calling Switch is installed on COP CAR. In emergency condition the users will press the switch and the GSM intercom will be activated for calling to MASTER Configured 3 numbers. To configure the GSM with three user no. the configuration command is to be send to GSM with three numbers by authorized person. FEATURES 4. Attractive sticker Simple installation and configuration. LED indication for Power, Calling and Status. Alert users with emergency calling. SPECIFICATIONS Mount Type- Wall Mount. Input Supply- 24V Mechanical Dimension in mm: 125mm X 100mm X 38mm 2w speaker MIC Calling Switch ANTENNA Reliable. Easy to use. Elegant and Durable. 3|Page 5. MOUNTING DETAILS: FOR GSM INTERCOM UNIT FOR EXTERNAL GSM INTERCOM UNIT 4|Page 6. INSTALLATION AND WIRING STEPS WITH IMAGES/DIAGRAM Note: Installation and Commissioning of the UNIT is to be done by Authorized, Trained technician of Elevator Company. Following are the steps to be taken for the installation of this unit. Open the unit by removing four corner screws on topside. Insert a valid SIM CARD (except JIO SIM) as shown below image, which are having proper range. Insert SIM CARD here and push gently into the slot Please connect the control panel's 2-pin MSTB m/f to 12V/24V and GND as shown in the diagram below. Then, as shown in the diagram below, connect the GSM INTERCOMM device's speaker, mic, and calling switch 6 pin MSTB m/f connector to the COP. FROM CONTROL PANEL 5|Page TO COP/EXTERNAL UNIT GSM INTERCOM unit will be placed at Machine room. Place the antenna at high network area. WIRING DIAGRAM MACHINE ROOM ANTENNA GSM INTERCOM SWITCH MIC SPEAKER POWER SUPPLY 24V TEL MIC1 MIC2 SPKP SPKN 24V 24V GND GND 2 PIN FEMALE R/A MSTB FROM PANEL/ SMPS 2 CORE CABLE 6 CORE CABLE (Customer scope) 1 2 3 4 5 6 6 PIN FEMALE R/A MSTB 6 PIN FEMALE R/A MSTB 11 22 33 44 55 66 EXTERNAL INTERCOM RECOWALL PLATE SPEAKER 6 CORE CABLE 1.5mtr 6 PIN MALE ST MSTB SWITCH MIC 6|Page 7. HOW TO OPERATE Switch on the POWER. On power ON PWR LED will glow (Continuously). PWR LED Wait for GSM SIM card initialization; the STATUS LED will blink until initialization is complete. After proper initialization, the STATUS LED will glow continuously. STATUS LED CONFIGURATION OF USER NUMBER IN GSM: By default, following numbers are authorized to give the Master set the configure number 1) 7757058738 (Kaustubh Sir). After configuring MASTER, the master has the authority to configure 3 user numbers. :CONF1:<user No.> e.g. :CONF1: xxxxxxxx96,xxxxxxxx90,xxxxxxxx10,111 After configuring the number, then the GSM INTERCOM will send the SMS from the master. For e.g.- GSMINTERCOMM, CONF1 OK, 12:14 14/10/22 When Configuring the GSM INTERCOM numbers STATUS LED will blink. After GSM numbers are configured, the STATUS LED will glow continuously. 7|Page CALLING PROCESS: After pressing the switch, it will start calling the users. If the calling 1 (first user) will not receive, is busy, switched off, or is not reachable, then it will automatically shift to the calling 2 (second user) If calling 2 and 3 do not receive, are busy, switched off, or are not reachable, the calling process will be repeated from calling 1 to calling 3 once more In this process, if anyone of the users (call1,2 or 3) will receive the call then the respective will LED will glow continuously and after ending it will OFF. While this process, if telephone switch is pressed, the calling process restarts again. 8|Page