Assembly Instructions
Caution: You must read this before you proceed.
Care & Maintenance
- ✔️ Furniture may scratch floors. We recommend using furniture pads to protect your floors.
- ❌ Do not put hot items directly on furniture surface.
- ❌ Do not clean furniture with harsh cleansers or polish.
- ❌ Do not place furniture under direct sunlight.
- ❌ Do not place furniture near heating or cooling vents.
- ❌ Do not write on furniture without a padded barrier to protect the surface.
- ❌ Do not place furniture outside. For indoor use only.
- ❌ Not for commercial use. For residential use only.
- ? Stains may be removed with mild soap solution and damp cloth.
- ⚠️ Children should not climb or jump on the furniture.
- ✨ Dust and pick-up spills using a clean, non-colored, lint-free cloth.
WARNING!!
Furniture Tipping Risk. Serious risk of severe or fatal crush injuries can occur from furniture tipping over if not secured.
Children like to climb on furniture and Unsecured furniture can pose a serious danger.
Please follow all instructions and install the tip-over restraints provided.
Queen Size Bed
NOTE: This Bed is NOT a TOY.
Keep your child / children at bay during the assembly process.
The BED is HEAVY.
To prevent injury to yourself or damage to the product a minimum of two adults are required whenever moving or lifting the product.
Parts List
| No. | Picture | Description | Qty |
|---|---|---|---|
| 1 | Diagram of Headboard | Headboard | 1 |
| 2 | Diagram of Footboard | Footboard | 1 |
| 3 | Diagram of Left Side Wing | Side wings-Left | 1 |
| 4 | Diagram of Right Side Wing | Side wings-Right | 1 |
| 5 | Diagram of Right & Front Side Rail | Side rails-Right &Front | 1 |
| 6 | Diagram of Right & Rear Side Rail | Side rails-Right & Rear | 1 |
| 7 | Diagram of Left & Rear Side Rail | Side rails-Left&Rear | 1 |
| 8 | Diagram of Left & Front Side Rail | Side rails-Left&Front | 1 |
| 9 | Diagram of Cross Slat with Mounting Position | Cross Slat With Mounting Position | 1 |
| 10 | Diagram of Cross Slat without Mounting Position | Cross Slat Without Mounting Position | 1 |
| 11 | Diagram of Front Side Bar | Side bars-Front | 2 |
| 12 | Diagram of Rear Side Bar | Side bars-Rear | 2 |
| 13 | Diagram of Middle Bar | Middle bars | 2 |
| 14 | Diagram of Plastic Cap (End) | Plastic caps-End | 24 |
| 15 | Diagram of Slat | Slats | 24 |
| 16 | Diagram of Plastic Cap (Middle) | Plastic caps-Middle | 12 |
| 17 | Diagram of Back of Fabric | Back of Fabric | 1 |
Hardware
| No. | Picture | Description | Qty |
|---|---|---|---|
| A | Diagram of Bolt (M8*18mm) | Bolts(M8*18mm) | 38 |
| B | Diagram of Bolt (M8*40mm) | Bolts(M8*40mm) | 10 |
| C | Diagram of Bolt (M8*45mm) | Bolts(M8*45mm) | 18 |
| D | Diagram of Metal Bracket | Metal Brackets | 2 |
| E | Diagram of Corner Bracket | Coner Brackets | 2 |
| F | Diagram of Metal Bracket | Metal Brackets | 2 |
| G | Diagram of Nut | Nut | 3 |
| H | Diagram of Washer | Washer | 4 |
| I | Diagram of Metal Bracket | Metal Brackets | 2 |
| J | Diagram of Middle Feet (24cm) | Middle feet(24cm) | 2 |
| K | Diagram of Middle Feet-U shape (24cm) | Middle feet-U shape(24cm) | 1 |
| L | Diagram of Support Feet-Front (24cm) | Support feet-Front(24cm) | 1 |
| M | Diagram of Support Feet-Side (16.5cm) | Support feet-Side(16.5cm) | 2 |
| N | Diagram of Plastic Feet (5*6cm) | Plastic Feet(5*6cm) | 2 |
| O | Diagram of Spanner | Spanner | 1 |
| P | Diagram of Allen Wrench | Allen Wrench | 1 |
Assembly Preparation
Before Beginning Assembly:
- ? Read instructions, cover to cover.
- ??? Have 2 or 3 adults on hand for assembly.
- ❌ Do not assemble on flooring or carpet.
- ? Assemble on a clean non-marring surface (packing foam).
- ? Save all packaging until finished.
Diagram shows all parts (1-17) and hardware (A-P) with their respective quantities. Parts include Headboard (1), Footboard (2), Side wings (3, 4), Side rails (5-8), Cross slats (9, 10), Side bars (11, 12), Middle bars (13), Plastic caps (14, 16), and Slats (15), Back of Fabric (17). Hardware includes various Bolts (A, B, C), Brackets (D, E, F, I), Nuts (G), Washers (H), Feet (J, K, L, M, N), Spanner (O), and Allen Wrench (P).
Assembly Steps
Step 1
Diagram shows Headboard (1) with Side wings-Right (4) and Side wings-Left (3) being attached. Bolts (C) and Allen Wrench (P) are indicated. Quantities shown: 4x Bolt C.
First attach the Side wings-Right (4) and Side wings-Left (3) to the Headboard (1) using Bolts (C) and Allen Wrench (P).
Please note that the shapes of Bolts (A) and (B) and (C) are similar. Please install according to the instructions and distinguish them!
Step 2
Diagram shows Headboard (1) with Back of Fabric (17) being attached to the velcro on the back.
Attach Back of Fabric (17) to the back velcro of Headboard (1).
Step 3
Diagram shows Footboard (2) with Plastic Feet (N) being attached. A close-up shows the attachment point. Quantity shown: 2x Plastic Feet N.
Fix the Plastic feet(N) to the Footboard(2).
Step 4
Diagram shows the assembly of Side rails-Right & Front (5) and Side rails-Right & Rear (6) with Side bars-Front (11) and Side bars-Rear (12) using Bolts (C). It also shows the assembly of Side rails-Left & Rear (7) and Side rails-Left & Front (8) with Side bars-Rear (12) and Side bars-Front (11) using Bolts (C). Quantities shown: 14x Bolt C.
First put the Side rails-Right &Front(5) with Side rails-Right &Rear(6) together,and use the Bolts (C) assemble the Side bars-Front(11) to the Side rails-Right &Front(5), and use the Bolts (C) assemble the Side bars-Rear(12) to the Side rails-Right &Rear(6).
Second put the Side rails-Left &Rear(7) with the Side rails-Left &Front(8) together,and use the Bolts (C) assemble the Side bars-Rear(12) to the Side rails-Left &Rear(7), and use the Bolts (C) assemble the Side bars-Front(11) to the Side rails-Left &Front(8).
Please note that the shapes of Bolts (A) and (B) and (C) are similar. Please install according to the instructions and distinguish them!
Step 5
Diagram shows Side rails-Left & Rear (7) being attached to the left side of Footboard (2) using Bolts (A) and Corner Brackets (E). It also shows Side rails-Right & Rear (6) being attached to the right side of Footboard (2) using Bolts (A) and Corner Brackets (E). Quantities shown: 12x Bolt A, 2x Corner Bracket E.
First put Side rails-Left&Rear(7) together with the left side of Footboard(2). The Footboard(2) and Side rails-Left &Rear(7) are assembled using Bolts(A) and Coner Brackets(E).
Second place Side rails-Right&Rear(6) with the right side of Footboard(2) and connect the two sections using Bolts(A) and Coner Brackets(E).
Please note that the shapes of Bolts (A) and (B) and (C) are similar. Please install according to the instructions and distinguish them!
Step 6
Diagram shows Side wings-Right (4) and Side rails-Right & Front (5) being assembled using Bolts (A) and Metal Brackets (F). It also shows Side wings-Left (3) and Side rails-Left & Front (8) being assembled using Bolts (A) and Metal Brackets (F). Quantities shown: 12x Bolt A, 2x Metal Bracket F.
First put Side wings-Right(4) and Side rails-Right &Front(5) together, then assemble them using Bolts(A) and Metal Brackets(F).
Second put Side wings-Left(3) and Side rails-Left &Front(8)together, then assemble them using Bolts(A) and Metal Brackets(F).
Please note that the shapes of Bolts (A) and (B) and (C) are similar. Please install according to the instructions and distinguish them!
Step 7
Diagram shows Metal Brackets (I) being attached to the Cross Slat With Mounting Position (9) using Allen Wrench (P) and Bolts (A). Quantities shown: 2x Metal Bracket I, 2x Bolt A.
Attach the Metal Brackets(I) into the Cross Slat With Mounting Position(9) using Allen Wrench(P) and Bolts(A) Up.
Please note that the shapes of Bolts (A) and (B) and (C) are similar. Please install according to the instructions and distinguish them!
Step 8
Diagram shows Metal Brackets (I) being assembled with Metal Side wings-Right (4) using Allen Wrench (P) and Bolts (A). It also shows Metal Brackets (I) being assembled with Side wings-Left (3) using Allen Wrench (P) and Bolts (A). Quantities shown: 2x Metal Bracket I, 2x Bolt A.
First,Assemble the Metal Brackets(I) and Metal Side wings-Right(4) together using Allen Wrench(P) and Bolts(A).
Second,Assemble the Metal Brackets(I) and Side wings-Left(3)together using Allen Wrench(P) and Bolts(A).
Please note that the shapes of Bolts (A) and (B) and (C) are similar. Please install according to the instructions and distinguish them!
Step 9
Diagram shows Support feet-Side (16.5cm) (M) being assembled into the Cross Slat Without Mounting Position (10) using Allen Wrench (P) and Bolts (A). Quantities shown: 2x Support feet-Side M, 2x Bolt A.
Assemble the Support feet-Side(16.5cm)(M) into the Cross Slat Without Mounting Position(10) using Allen Wrench(P) and Bolts(A) Up.
Please note that the shapes of Bolts (A) and (B) and (C) are similar. Please install according to the instructions and distinguish them!
Step 10
Diagram shows Support feet-Side (16.5cm) (M) being assembled with Right rails using Allen Wrench (P) and Bolts (A). It also shows Support feet-Side (16.5cm) (M) being assembled with Left rails using Allen Wrench (P) and Bolts (A). Quantities shown: 8x Bolt A, 8x Support feet-Side M.
First,Assemble the Support feet-Side(16.5cm)(M) and Right rails together using Allen Wrench(P) and Bolts(A).
Second,Assemble the Support feet-Side(16.5cm)(M) and Left rails together using Allen Wrench(P) and Bolts(A).
Please note that the shapes of Bolts (A) and (B) and (C) are similar. Please install according to the instructions and distinguish them!
Step 11
Diagram shows Middle bars (13) being assembled with Support feet Front (24cm) (L) using Bolts (B), Washer (H), and Metal Brackets (D). It also shows Middle bars (13) being assembled with Metal Brackets (D) using Bolts (B), Washer (H), and Nut (G). Finally, it shows Middle feet (24cm) (J) being assembled to the Middle bars (13) using Allen Wrench (P) and Bolts (B). Quantities shown: 2x Bolt B, 4x Washer H, 2x Metal Bracket D, 1x Nut G, 2x Middle feet J.
First, Using the Allen Wrench(P) to make the Bolts(B) and Washer(H) and Metal Brackets(D) to assemble the Middle bars (13) and Support feet Front(24cm)(L) together.
Second,Using the Allen Wrench(P) and Spanner(O) to make the Bolts(B) Bolts(B), and Washer(H) and Nut(G) to assemble the Middle bars(13) and Metal Brackets(D) together.
Third,using Allen Wrench(P) and Bolts(B) to make the Middle feet(24cm)(J) assemble to the Middle bars(13), as shown above, and Please repeat this step.
Please note that the shapes of Bolts (A) and (B) and (C) are similar. Please install according to the instructions and distinguish them!
Step 12
Diagram shows Middle feet-U shape (24cm) (K) being connected to the 2 Middle bars (13) using Allen Wrench (P) and Bolts (B). Quantities shown: 2x Middle feet-U shape K, 2x Bolt B.
Using the Allen Wrench(P) and Bolts(B) to connect Middle feet-U shape(24cm)(K) to the 2 Middle bars(13).
Please note that the shapes of Bolts (A) and (B) and (C) are similar. Please install according to the instructions and distinguish them!
Step 13
Diagram shows Metal Brackets (D) being assembled into the Cross Slat With Mounting Position (9) using Allen Wrench (P) and Bolts (B). It also shows Metal Brackets (D) and Footboard (2) being assembled using Allen Wrench (P) and Bolts (A). Quantities shown: 2x Metal Bracket D, 2x Bolt B, 2x Bolt A.
First, Find the tools Allen Wrench(P) and Spanner(O) and use the Bolts(B) to assemble the Metal Brackets(D) into the Cross Slat With Mounting Position(9).
Second, the Metal Brackets(D) and Footboard (2) are assembled using the Allen wrench (P) and with Bolts (A).
Please note that the shapes of Bolts (A) and (B) and (C) are similar. Please install according to the instructions and distinguish them!
Step 14
Diagram shows Plastic caps-End (14) being attached to the edge of Slats (15). Plastic caps-Middle (16) are used to connect Slats (15) together. Slats (15) are then laid flat over the holes in the Side rails. Quantities shown: 14x Plastic caps-End, 16x Plastic caps-Middle, 15x Slats.
Assemble Plastic caps-End(14) on the edge of Slats(15)). Plastic caps-Middle(16) is used to connect the Slats(15)) on both sides together. Then lay the Slats flat over the holes in the Side rails.
Your Bed is ready for use.
Note: After assembly and before using the bed, inspect to make sure all parts are properly connected and securely fastened.
⚠️ WARNING
Serious or fatal crushing injuries can occur from tipping furniture. To help prevent tip-over: ALWAYS secure this furniture to the wall using a Safety Restraint Device. See product instructions for more ways to help prevent furniture tip-over.
