Instruction Manual for VEVOR models including: HE-18C-6M-ZJ, HE-18C-6E-US Electric Honey Extractor, HE-18C-6E-US, Electric Honey Extractor, Honey Extractor, Extractor
Electric Honey Extractor MODEL:HE-18C-6E-US MODEL:HE-18C-6E-US Electric Honey Extractor This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product. 1 INSTRUCTIONS Thank you very much for choosing this product. Please read all the instructions before using it. The information will help you achieve the best possible results. PLEASE NOTE! Drawings in this manual are for illustration purposes only and in some details may differ from the actual product. ATTENTION! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in serious injury or even death. Please place in a position that children cannot climb or move, so that the product does not fall over and injure children. SAVE THESE INSTRUCTIONS TECHNICAL PARAMETERS Model Capacity Height from the bottom of the barrel to the ground Frames Fit frame size mm Main materials HE-18C-6M-ZJ 18KG 30-40cm (lifting) Large frame*6 Small frame*6 Large frame: L485 * W160 Small frame: L485 * W140 201 stainless steel Model Voltage/fr equency Speed regulation range Locked rotor current Automatic stop (overload protection) when open the lid 110-130V HE-18C-6M-ZJ 60Hz 0~100% (maximum speed 280r/min) 1.404-1.648A possess 2 Structure diagram Motor Control box (Governor, reversible switch, power switch) Lid Barrel Body Support Leg Honey Valve Hardware & Part List 3 Assembly Step 1: Installation of Support Legs. First, take out the three legs and place the barrel on the ground. Next, align the holes on the three legs with the corresponding three holes on the barrel, insert screws into the holes, and tighten them with a screwdriver. Step 2: Installation of the Honey Valve. 4 First, erect the bucket and unscrew the retaining nut at the honey outlet. The elbow passes through the hole at the bottom of the barrel. Note that the sealing ring is above the bottom of the barrel and the elbow is close to the bottom of the barrel. The fixing nut passes through the elbow and is fixed and locked with the elbow screws. Step 3: Connect the power cord to the electrical port to power the honey extractor. Step 6: Turn the key to the No. 1 position, turn on the power, adjust the speed control knob to start the honey extractor. Adjust the rotation direction by reversing the switch. Reversible switch forword stop reversal Governor Power switch 1 --Open O-- Off Note: Before starting the machine, remove the cable tie fixed by the honey frame. 5 Step 4If you open the lid, the motor will stop working automatically. And if you close the lid, the motor will work normally. Step 5: Take out the honey. First, loosen the screw. Then hold the handle of the honey outlet connector, lift it to open the honey outlet, and let the honey flow out. 6 TROUBLESHOOTING INSTRUCTION Problem The motor does not start after the power is turned on Reason The plug is not tightly plugged in Solutions Insert the plug firmly The switch is not turned to 1 Turn the switch to 1 The speed control knob is not adjusted Adjust the control knob Barrel shaking The frames are not placed symmetrically Place the frames symmetrically The feet are not fixed on the Fix the feet on the ground ground CLEAN,CARE AND STORAGE RULES Care and cleaning : The honey extractor shall be thoroughly cleaned and dried before use. Especially the one that has not been used for a long time, shall be disassembled and cleaned. Otherwise, the honey stains and other impurities left in the honey shaker will pollute the honey. After using the honey extractor, clean the inner and outer walls of the barrel and its stainless steel frame. And dry them with a clean and dry cloth, use a hair dryer, or let them air dry to keep them clean to prepare for the next use. Storage : Please store it out of the reach of children; After using the honey extractor, place it in a cool place and cover it with a large cloth to prevent dust from entering. 7 Manufacturer: Shanghaimuxinmuyeyouxiangongsi Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN. EC REP: E-CrossStu GmbH. Mainzer Landstr.69, 60329 Frankfurt am Main. UK REP: YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730 8WPS 文字