Commercial Lighting Company | LED Lighting Solutions
Installation Guide for LITETRONICS models including: EB40, EB40 LED Emergency Battery Backup, LED Emergency Battery Backup, Emergency Battery Backup, Battery Backup, Backup
High Bay LED Lights | LED High Bay Light Fixtures
File Info : application/pdf, 8 Pages, 645.08KB
DocumentDocumentLED Emergency Battery Backup Installation Instructions Ordering Code: EB40 WHAT COMES IN THE BOX (1) EB40 unit (1) Installation instructions (1) Charging indicator test switch with 2 screws (1) Test switch cover (2) Waterproof nuts (1) Remote control (11) Wire nuts TOOLS NEEDED Wire stripper Wire cutter Phillips screwdriver Step ladder SAFETY WARNING AND INSTRUCTIONS When using electrical equipment, basic safety precautions should always be observed. Read and follow all safety instructions. · Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED Emergency Backup. Check for enclosed wiring and components. · Risk of fire or electric shock. This LED Emergency Backup installation requires knowledge of luminaire and electrical systems. If not qualified, do not attempt to install. Contact a qualified electrician. · Before installation, make certain the AC power to the fixture is off. · The electrical rating of this product is 100-347V Vac. Installer must confirm that there is 100-347V Vac to the fixture before installation. · To prevent electrical shock, only mate unit connector after installation is complete and before the AC power to the fixture is back on. · Do not use outdoors. · This LED Emergency Backup unit requires an un-switched AC power source of 100-347V Vac, 50/60Hz. · Do not let power supply cords touch hot surfaces. · Do not mount near gas or electric heaters. · Equipment should be mounted in locations and at heights where it is not subjected to tampering by unauthorized personnel. The use of accessory equipment is not recommended by the manufacturer and may cause an unsafe condition. · Do not use this equipment for other than its intended use - only use for LED Lighting emergency backup. · Use with grounded, UL/ETL listed, dry or damp location rated fixtures. · CAUTION: The EB40 provides more than one power supply output source. To reduce the risk of electrical shock, disconnect both normal and emergency source by turning off the A.C. branch circuit. · CAUTION: Servicing of this equipment should be performed by qualified personnel only. · CAUTION: Do not attempt to service the battery. A sealed, no-maitenence battery is used that is not field replaceable. Replace the entire unit when necessary. · CAUTION: The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition, void warranty, and result in non-compliance with UL specifications. · For use in 32°F minimum, to 122°F maximum ambient temperatures. Suitable for use in damp locations and plenum spaces. · Not for use in heated air outlets or hazardous locations. COMPATIBILITY The EB40 is compatible with all LED fixtures less than 300W. All fixtures must also include 0-10V dimming if wattage is greater than 40W. PLEASE NOTE: Although tested and compliant with UL924, when used with a sensor-equipped fixture, unless the sensor wiring is accessible and bypassed, the sensor settings will remain active, overriding the EB40 emergency power to the fixture, and cause the fixture to dim or turn off based on its occupancy programming. This may not be ideal during emergency egress and may not meet code requirements. We recommend that if the EB40 is used on a sensor-equipped fixture, the sensor be programmed to maintain full light output when occupancy sensing or daylight harvesting is active. 2 EB40 OPERATING INSTRUCTIONS · Litetronics Emergency Battery Backup unit (EB40) delivers 90-minutes of power to fixtures in the event of a power outage. · Once installed and receiving power, the unit will charge fully and remain in stand-by mode, and the indicator light will remain on. INDICATOR LIGHT · In AC operation, the indicator light will remain on/solid · In emergency operation, the light will flash slowly (on for 2 seconds, off for 2 seconds) · If a failure were to occur, the light will flash quickly (on for 0.2 seconds, off for 0.2 seconds) · The Indicator Light / Test Switch may be mounted on a switch box near the fixture. Although easy accessibility is not required, it must be visible to occupants. · The Red Button/Indicator Light is required via Class 2 wiring to enable full functionality of the EB40. TEST SWITCH · In AC operation, press the test button once to conduct a 30 second emergency test · In AC operation, press the test button twice (in 2 seconds timespan) to conduct a 90-minute full discharge test. Operation Manual for · During emergency operation, press the test switch once to shut off the unit Pictures: REMOTE TEST SWITCH · In AC operation, press test button A once to conduct a 30 second emergency test · In AC operation, press test button B once (in 2 seconds timespan) to conduct a 90-minute full discharge test. · During emergency operation, press the test switch once to shut off the unit · Range - With the antenna extended, the range will be up to 40'. AUTOMATIC SELF-TESTING · The EB40 includes a self-testing function, which will perform a 30-second discharge test once a month and a full discharge test one a year. At this time, the unit will simulate an AC power failure and automatically switch to emergency mode. During routine testing, the unit will monitor the operation of the LED load, battery voltage, an emergency duration. If the unit detects any problems, the indicator light will flash quickly. antenna 30 SECONDS A MAINTENANCE B Although no routine maintenance is required to keep the emergency battery backup functional, 90 MINUTES it should be checked periodically to ensure that it is working. The following schedule is recom- mended: · Visually inspect the charge indicator light monthly. It should be illuminated. · Test the emergency operation of the fixture at 30-day intervals for a minimFumeaotfu3r0essec:onds. · Conduct a at least 90 90-minute minutes. discharge test once a year. LED fixture should operate1,aRt uepmtoot4e0TWe sfot rSwitch: Signa 2,One test switch could contr as long as they are within t SERVICE Should be performed as indicated above by qualified personnel. 3 INSTALLATION BEFORE BEGINNING INSTALLATION, TURN OFF POWER AT THE CIRCUIT BREAKER. 1. Choose a location for the Emergency Battery Backup unit. The indicator light/ test switch should be mounted where they can be easily seen by inspectors. 2. The input voltage to the dimmable wires (DIM+, DIM-) of the EB40 must be less than 20Vdc. Emergency LED Driver 3. Once mounted, select the appropriate wiring diagram to connect the EB40 to the AC driver. Use wirenuts to cap unused wires and make sure all connections are inEaMccoArdXanXceFwiYth tSheeNrEiCeasnd any local regulations. 4. Restore power to the fixture. When power is received, the red indicator light should appear, indicating that the unit is charging. An initial full charge could take up to 24 hours. A: For 30 seconds/Off B: For 90 minutes In AC operation, press test switch or "A" on remote test switch, the fixtures will switch into emergency model for 30 seconds. In AC operation, press "B" on remote test switch, the fixtures will switch into emergency model for 90 minutes. In emergency operation, 30 senconds later, press "A" on remote test switch 10 seconds later, the fixtures will switch into AC model. The antenna shall be extended before test, the remote signal could reach about 12M. WIRWIiNriGngDDIAiaGgRraAmMS When *thWe hLEeDndrtihveer pleodwedr irsivleessrtphaonwtheeremleesrgsetnhcyapnowthere(4e0mW)ergency power A)Normal AC-N AC-L Connect to AC-N WHITE BLACK KIT CHARGE INDICATOR- Connect to AC-L Connect to harging Indicator- GGRRAAYY(-) CHARGING INDICATOR TEST SWTCH TEST SWITCH CHARGE INDICATOR WALL SWITCH No connect Connect to Test Switch Connect to harging Indicator YELLOW RED Connect to Wall Switch BLACK/WHITE PPIINNOKKR(-A) NGE BLUEPPURRPPLLE(E+) LED LAMP with internal driver DRIVER N LED TUBE DRIVER L Connect to Driver N Connect to Driver L BROWN USE WIRE NUTS TO COVER UNUSED WIRES 4 pg2 Rev:V02 *When the led driver power more than the emergency power *BW)Wheitnh tDhiemlmederdriver power more than the emergency power WhenBth)We LiEtDhdDrivimer mpoewrer is greater than the emergency power (40W) A - With dimmer WHITE BWLAHCITKE BLACGKRAY GGRRAYA(Y-) AC-N Connect to AC-N AACC--NL AC-L 0~10V DIMMER 0~10V DIMMER KIT KIT CHARGING INDICATOR TEST SWTCH CHARGING INDICATOR TEST SWTCH AC-L out ADCIM-L- out DIM- CCoonnnneecctt ttoo AACC--NL CHARGE INDICATORCHARGE INDICATOR- Connect to ConnecthtaorgAiCn-gL CInodninceactot rtoharging CInodninceactot rto- TEST SWITCH TEST SWITCH CHARGE INDICATOR CHARGE INDICATOR Connect to DIM- Connect Connect to to DDIIMM+- (Dimmer) CCoonnnneecctt ttooDDIIMM++((DDirmivmere)r) Test Switch CCoonnnneecctt ttoo YELLOW TehstaSrgwinitgch ICnodnicnaectot rto YREELLDOW harging ICnodnicnaectot rto Wall Switch BRLAECDK/WHITE WCoanllnSecwt ittocPPPIhNIINNOOKKK(RR-B)AALNNAGGCEEK/WHITE BROWNBRO BWLNUEPPUURRBPLPLELU(E+E)PURPLE DIM+ DIMD+IMLED LAMP LDEIMD-LED LAMP LED-+ LED+ Connect toDIM+( Driver) DIM+ DRIVER N DIML+ED DRIVER DRIVER N LED DRIVER DRIVER L DRIVER L Connect to Driver N Connect to CDorinvneer cNt to Driver L Connect to Driver L CAUTION: For Diagrams A, B, C, D, E, Pink/Gray(-) & Purple(+) Dimming leads from EMBB Must Be Connected to Driver Dim +/- leads / terminal Blocks. If connection is not made, the LED Array will flicker and shut down after 10 seconds in 99% of the cases while in emergency mode. In some cases, the EMBB will fail as it will overheat. Dimming circuit helps to limit higher driver load to 10W. C)Without Dimmer C)Without Dimmer B - Without dimmer AC-N AACC--NL AC-L No connect No connect Connect to AC-N WHITE BWLAHCITKE BLACGGKRRAYA(-Y) GRAY CCoonnnneecctt ttoo AACC--NL KIT KIT CHARGE INDICATORCHARGE INDICATOR- Connect to ConnecthtaorgAiCn-gL CInodninceactot rtoharging CInodninceactot rto- TEST SWITCH CHARGING INDICATOR TEST SWTCH CHARGING INDICATOR TEST SWTCH TEST SWITCH CHARGE INDICATOR WALL SWITCHARGE INDICATOR WALL SWITCH DIM- Connect to DIM- DIM- CCoonnnneecctt ttoo DDIIMM+- (Dimmer) CCoonnnneecctt ttooDDIIMM++((DDirmivmere)r) Test Switch CCoonnnneecctt ttoo YELLOW TehstaSrgwinitgch ICnodnicnaectot rto YREELLDOW harging ICnodnicnaectot rto Wall Switch BRLAECDK/WHITE WCoanllnSecwt ittoPcPPIhNIINNKOO(KKRR-B)AALNNAGGCEEK/WHITE BROWNBRO BWLNUEPURBLPLUEEPPUURRPLPEL(E+) Emergency LED Driver LED LAMP DIMLDEIMD-- Connect toDIM+( Driver) DIM+ DRIVER N DIML+ED DRIVER DRIVER N Connect to Driver N Connect to CDorinvneer cNt to LED LAMP LED-+ LED DRIVER Driver L EMAXXFY Series USE WIRE NUTS TO COVER UUSNEUSWEIDREWNIRUETSS TO COVER UNUSED WIRES DRIVER L Connect to D) WitLhED+out SwitcDhRIVERaLndDriveWr L ithout Dimmer C - Without switch & dimmer WHITE BLACK AC-N AC-L pg3 pg3 KIT Connect to AC-N CHARGE INDICATOR- Connect to AC-L Connect to harging Indicator- GGRRAAY(Y-) No connect CHARGING INDICATOR TEST SWTCH DIM- TEST SWITCH CHARGE INDICATOR Connect to Test Switch Connect to harging Indicator YELLOW RED Connect to DIMConnect to DIM+(Dimmer) Connect to Wall Switch BLACK/WHITE PPIINNOKK(R-)ANGE Connect toDIM+( Driver) BLUEPPUURRPLPEL(E+) BROWN DIM- DIM+ Connect to DRIVER N Driver N LED LAMP LEDLED+ LED DRIVER Connect to Driver L DRIVER L 5 USE WIRE NUTS TO COVER UNUSED WIRES Rev:V02 Rev:V02 E) With Sensor (AC) D - With sensor (AC) WHITE BLACK AC-N AC-L Connect to AC-N KIT CHARGE INDICATOR- Connect to AC-L Connect to harging Indicator- GGRRAAYY(-) AC SENSOR CHARGING INDICATOR TEST SWTCH AC-L out DIM+ DIM- TEST SWITCH CHARGE INDICATOR Connect to DIM+(Dimmer) Connect to DIMConnect toDIM+( Driver) Connect to Test Switch Connect to YELLOW harging Indicator RED Connect to Wall Switch BLACK/WHITE ORPPAININNKGK(-)E BLUEPPUURRPPLEL(E+) BROWN DIM- DIM+ Connect to DRIVER N Driver N Emergency LED Driver LEDLAMP LEDLED+ LED DRIVER Connect to Driver L DRIVER L F) With Sensor (DC12V) E - With sensor (DC12) pg4 AC-N AC-L KIT CHARGING INDICATOR TEST SWTCH AC-L out Connect to AC-N WHITE BLACK Connect to AC-L CHARGE INDICATOR- Connect to harging Indicator- GGRRAYA(-Y) TEST SWITCH CHARGE INDICATOR Connect to TCeosnt nSewctittcohYELLOW harging Indicator RED Connect to Wall Switch BLACK/WHITE PPUURRPLPEL(+E) ORANGE BROWBNLUE DIM- Gray(Dim-) Purple(Dim+) DIM+ Red(12V) SENSOR DC DIM- LED LAMP LEDLED+ Connect to DIM- PIPNIKN(-K) Connect to DIM+(Dimmer) Connect toDIM+( Driver) DIM+ DRIVER N LED DRIVER DRIVER L Connect to Driver N Connect to Driver L USE WIRE NUTS TO COVER UNUSED WIRES EMAXXFY Series Rev:V02 SELF-TEST The emergency LED driver contains a control/monitor circuit which will perform a 30-second discharge test once a month and a fully discharge test once a year. At this time, the unit simulate an AC power failure and automatically switch to emergency mode. During routine testing, the unit will monitor the operation of the LED load, battery voltage, and emergency duration, if the unit detect any problems, the indicator will flash quickly. Dimensions Emergency LED Driver Picture L1 L2 R1 R2 Length Width Height Size(inch) Radius Flexible Conduit Connector Length of Conduit Diameter Diameter the wire L1 L2 W1 W2 / R1 R2 / / / / 6 12.32" 11.73" 2.32" 1.65" 1.48" 0.14" 0.08" 13" 0.75" 0.79" 5.51" W1 W2 COMPATIBILITY The EB4 0 is compatible with Litetronics LED fixtures using greater than 200W. All fixtures must also include 0-10V dimming. Below is a complete list of Litetronics compatible fixtures. LED HIGH BAY PL HBC115XX HBC115XXT HBC175XXT HBC220XXT HBC240XX LED NSF HIGH BAY HBF150XX HBF100WXXDLP HBF150W7XXDLP LED HIGH BAY SL HSB150XX HBS100B2XXDLP LED HAZARDOUS LOCATION HBE150B150DLP - [1> HBE200B150DLP - [1> LED HIGH CEILING PANEL HOPT2 HOPT4 - </= 260W. Not for 290 & 325W. LED LINEAR HIGH BAY LHB88 LHB112 LHB148 LHB248 LED LINEAR HIGH BAY C-SERIES LHBC105 LHBC155 LHBC200 LHBC240 [1> EB40 is not Hazardous Location Rated. Must be remote mounted. The EB40 is compatible with all LED fixtures using less than 300W. All fixtures must also include 0-10V dimming. UL924 STATEMENT OF COMPLIANCE AND COMPATIBILITY PLEASE NOTE: When used with a sensor-equipped fixture from the Approved List of Litetronics fixtures below, the sensor will be bypassed and disabled by the EB40 when wired correctly per the installation instructions and cause the fixture to remain illuminated during periods of vacancy when the compatible fixture is powered by the EB40 power source. As such, EB40 is UL924 compliant. Approved Fixtures WITHOUT SENSOR LHB88, 112, 148, 248, HBC115, HBC240, HBC175**T, HBC220**T, HBE150, 200, HBF150, HBS100, 150, HOPT2,4, LHBC105-240 Approved Fixtures WITH SENSOR HBS100, 150, LHB88-248 Unapproved Fixtures HBC175, HBS200, LHB148HV NOTES 7 Thank you for choosing 6969 W. 73rd Street Bedford Park, IL 60638 www.Litetronics.com CustomerService@Litetronics.com or 1-800-860-3392 The information and product specifications contained in these instructions are based upon data believed to be accurate at the time of printing. This information is subject to change without notice and without incurring liability. If you have questions regarding specific product details, please contact us at 800-860-3392 or via email at customerservice@litetronics.com. To check for an updated version of these instructions, please visit www.litetronics.com. 11/2/22 - V2.3