User Manual for xpr models including: MTPADP-BT-EH-SA Bluetooth Standalone Keypad with Integrated RFID Reader, MTPADP-BT-EH-SA, Bluetooth Standalone Keypad with Integrated RFID Reader, Integrated RFID Reader, RFID Reader, Reader
XPR MTPADPBK-BT-EH-SA Standalone tastiera lettore RFID
2023-01-29 — USER'S MANUAL. MTPADP-BT-EH-SA. Bluetooth standalone keypad with integrated RFID reader. 1. SPECIFICATIONS. User capacity: Relays: Output: Entry mode: RFID ...
File Info : application/pdf, 3 Pages, 1.51MB
DocumentDocumentMTPADP-BT-EH-SA EN Bluetooth® standalone keypad with integrated RFID reader USER'S MANUAL 1. SPECIFICATIONS User capacity: Relays: Output: Entry mode: RFID reading type: Reading distance: PIN Code Length: Power supply: Buzzer, backlight control: Tamper: RS-485 interface: Door Open Time: IP Factor: Operating Temperature: Operating Humidity: Firmware upgrade: Wiegand output: Programming: Door operation: Holidays: Event capacity: 100 Cards and 100 PIN Codes 1 or 2 depending on the remote relay unit 1 with RTT and RU1 and 2 with RU2 and DINRTT RS-485, Wiegand PIN Code, Card, PIN Code or Card EM 4002/4100 and HID (125kHz) up to 4cm 6 Digits 12 VDC; max. 100mA Yes, ON/OFF via XPR Smart Admin Yes Yes, for connecting I/O boards like RU1, RTT, RU2, DINRTT 0 to 255 sec. or toggle (ON/OFF mode) IP65 20ºC to +50ºC 5% to 95% RH without condensation Yes, via Bluetooth® wireless technology Wiegand 24, 26, 32, 34, 56, 58 bits or 4, 6, 8 bit per key for the keypad via XPR Smart Admin via XPR Smart Access 24 4000 Important note: The Bluetooth® reader comes with RU1 remote relay unit. Make sure to make firmware update with the latest available firmware. 2. MOUNTING 51mm 92mm 27mm Ø6.0 Cable 5mm Tricolor indication LED v.b8 Reset Service mode 30mm xx xx xx xx d1 dg0nd +12V 3 (3 x 30mm) 1 (M3 x 6mm) 3. RESET READER TO DEFAULT 1. Turn the device OFF ON 2. Put dipswitch 1 to position ON 3. Turn the power ON 12 4. Wait approx. 15 seconds until continuous beeps. 5. Put dipswitch 1 to OFF 6. Wait for long beep and orange back light led. Access Granted (Output 1 or 2) Idle Mode Access Denied The reset procedure will bring the reader to default. The password will be deleted, all the users and the reader will be unpaired from the remote relay unit. Unpairing the reader after reset, prevents unauthorized reset and keeps the unit in high security state. 1 4. WIRING AND PAIRING There are four options to wire and pair the reader. It can be paired to RU2, RU1, DINRTT and RTT. Red Black White Yellow +12V GND D0 D1 Power Supply Wiegand to wiegand controller Pink A Violet B Grey Blue RS-485 Tamper to remote relay unit RU2 2 Relay Remote Unit DINRTT 2 Relay Remote Unit and request-to-exit Button IN RS-485 (max. 50m) OR NO COM NC Power Supply +12V GND GND_P B PB B RS 485 A RU1 1 Relay Remote Unit RTT Secured Area 1 Relay Remote Unit and request-to-exit Button Unsecured Area MTPADP-BT-EH-SA Bluetooth standalone keypad with integrated RFID reader 4.1 Wiring and pairing MTPADP-BT-EH + RU1 Pairing Reader with RU1 (high security) 12 VDC + - Pairing the reader with remote relay unit is done from the remote relay unit and enables added security. After being paired, it is not possible to switch any of the devices, since the reader will work only with the paired remote relay unit. The Bluetooth reader must be connected to remote relay unit, unless is used as wiegand reader. The remote relay units compatible with MTPADB-BTEH-SA are RU1, RU2, RTT and DINRTT. Once connected, the remote relay unit must be paired with the Bluetooth reader. - Keep the button pressed for at least 5 sec. and the units will be paired. + Electric Door Strike - white yellow gray NO COM NC Power Supply +12V GND GND_PB PB B RS-485 A red black blue orange violet pink Other pairing devices: Device Description RU2 DINRTT RTT DIN rail mount remote relay unit Flush mount sensitive push button and remote relay Surface mount sensitive push button and remote relay 4.2 Wiring MTPADP-BT-EH-SA to wiegand controller Red Black White Yellow Pink Violet Grey Blue Max 150m + - D0 D1 12V DC(CC) Host/ Unité Centrale/ Unita' centrale/ Sistema receptor/ Controller/ Controller Red Black Exit Button Violet Pink max. 50 m Reader Relays 2 2 1 By default, the reader is set to Wiegand 26 bit for both the keypad and the RFID reader. You can set the reader, using the software, to Wiegand 24, 26, 32, 34, 56, 58 bits. You can set the keypad to send 4, 6 or 8 bits per key, while the RFID reader (card) sends wiegand. 2 5. SETTING UP READERS WITH XPR SMART ADMIN WINDOWS SOFTWARE 1. Add site first. 2. Click on "ADD" reader. 3. Select type "MTPADP-BT-EH-SA". 4. Scan for readers near by by clicking on "Scan". Found readers will be listed (pic.2). Click on "Select". 5. Add a pairing key between the PC and the Bluetooth reader and a password. (pic. 3) 6. If the pairing is successful, the buttons in the reader section will be enabled. (pic.4) pic. 1 pic. 4 pic. 2 pic. 3 You can download 2 softwares for Windows: XPR Smart Access and XPR Smart Admin from our website: Users Software Application for users, allowing them to manage the doors from a distance. (max distance: 10m). 6. ADDING USERS Administrator Software Software for the installation administrator, allowing him/her to program all readers and update them, manage users and their access rights, download events and edit reports. 1. Go to Users and select the user. Edit the name directly. Enable it. 2. Put a PIN Code and Card ID. The Card ID can be read directly from the reader or from USB desktop reader. 3. Select proper Access level and validity period. 4. After this, go to the reader and "Upload users to reader". The 2 smartphone apps are available in: Users App Web page wwww.xprgroup.com Administrator App Smart Access Application for users, allowing them to manage the doors from a distance. (max distance: 10m). Smart Admin Application for the installation administrator, allowing him/her to program one reader at a time and update it, manage users and their access rights, download events and edit reports. This product herewith complies with requirements of EMC directive 2014/30/EU, Radio Equipment Directive 2014/53/EU. In addition it complies with RoHS2 directive EN50581:2012 and RoHS3 Directive 2015/863/EU. 3