5 Inch 1080P Full HD Baby Monitor User Manual

1. What's Included:

Camera * 1
LCD Monitor * 1
Mounting Bracket * 1
Power Adaptor * 2
Type-C Cable * 1
Micro USB Cable * 1
Screws * 1
User Manual * 1

2. Key and Interface Introduction

Camera Interface:

1. Lens
2. Sound pickup
3. Light sensor
4. Reset Button
5. For upgrade use
6. Speaker
7. Antenna
8. Digital Temp Sensor
9. Micro USB Port

Monitor Interface:

1. Indicator LED: Green when working, Red when charging, turns Green when fully charged.
2. Back Button: In Monitoring Mode, press to enter volume and brightness settings. In Main Menu, press to return to the previous menu.
3. Camera Switch Button: Press to cycle through connected cameras.
4. Direction Button: In Monitoring Mode, controls Pan and Tilt of the camera. In Main Menu, selects options.
5. Type-C Charging Port.
6. OK button: Enter menu and confirm settings.
7. Lullaby Button: Press to play lullabies, press again to pause, press again to play the next lullaby.
8. Talk Button: Press to talk (audio off), press again to enable live audio.
9. Mic
10. Sound Detection (VOX) Button: Press to enable sound detection (displays ✔), press again to disable.
11. Power On/Off Button: Long press to turn on/off, short press for standby mode.
12. External Antenna: Extend for optimal signal.
13. Bracket
14. Speaker
15. TF Card Port: Insert TF card when the monitor is off. Format the TF card when prompted on first use. Press OK to format for auto-record mode.

3. Status Introduction

① Signal strength indicator.
② Battery level indicator.
③ Temperature display.
④ Time display.
⑤ Camera status indicator.
⑥ Sound indicator.
⑦ Speaker icon: Indicates two-way audio is active.
⑧ Sound Alarm indicator: Shows when sound alarm is enabled.

4. Connect the camera to the Monitor

Power on the camera. It will announce "power on system starting up" and begin working (approx. 3-5 seconds).
Long press the power on/off button on the monitor to turn it on. Ensure the monitor is fully charged before the first connection.
Wait approximately 10 seconds for the picture to appear on the monitor. The baby monitor is now ready for use.

5. Add new camera

Navigate to the main menu, select 'Camera' (✓), choose a channel, and double-press the OK button to start matching. The status will show 'Configuring' then 'Connected' (Pic 2, Pic 3).
If pairing fails, ensure the camera is powered on. Reset the camera and repeat step 4.1.
To connect up to 4 cameras, add them sequentially from CH1 to CH4. Select the corresponding channel when adding each camera. In the preview, the left corner displays the currently viewed channel.

6. Feed Timer Setting

Access the menu and select 'Feed Timer' ( ). Use the up/down buttons to select the time interval and left/right buttons to choose between single time, recycle, or turn off the timer.
After setting the feed timer, you can select either a single instance or a recurring schedule.
To disable the feed timer function, turn off the clock setting.

7. Sound Detection

From the main menu, select 'Sound detection' ( ). Options include Low, Medium, High, and Optional sensitivity levels.
Press the 'VOX' button on the monitor to toggle sound detection on or off. When enabled, a '✔' symbol appears on the display.
When the camera detects sound exceeding the set threshold (DB range), the LCD screen will illuminate, and an alarm sound will play for approximately 30 seconds. If the sound persists, the alarm will continue. Press any button on the monitor to stop the alarm.

8. Play the lullaby

Navigate to the main menu and select the 'Music' icon ( ). Choose from lullabies No. 1 to No. 6. The selected lullaby's name will appear in the top-left corner of the screen during playback.
Lullaby List:
- 1. Castle in the Sky
- 2. Grave of the Fireflies
- 3. Passive
- 4. Spirited Away
- 5. Street of Sea
- 6. The Love That Transcends Time

9. Temperature Detection Alarm

The temperature alarm can be set in Celsius (°C) or Fahrenheit (°F).
The default safe temperature range is 18-30°C. Alarms will trigger if the temperature falls below or rises above this range.
When the temperature alarm is activated, the LCD monitor will turn on, display a thermometer icon ( ), and emit an alarm sound for 30 seconds. Continuous detection of out-of-range temperatures will result in continuous alarm sounds. Press any button to silence the alarm.

10. Display Settings

Display settings include Dormant mode and Brightness (LUMI).
Dormant mode can be set to 30 seconds ( ), 60 seconds ( ), 90 seconds ( ), or 'ALWAYS ON' ( ). Adjust as needed.
Brightness can be set to values like 20 ( ), 50 ( ), 90 ( ), or 'Customize' ( ). When the LCD is off, two-way audio remains active. When the LCD is on, live audio is also active.

11. Language Settings

The device supports 8 languages: ENGLISH, JAPANESE, CHINESE, PORTUGUESE, ITALIAN, FRENCH, SPANISH, GERMAN. The default language is ENGLISH.
Select your preferred language. After confirming, power off and restart the monitor. The connected camera will adopt the monitor's language setting.
Ensure the camera is powered on when changing the language.

12. System Settings

12.1: Time & Date Settings

Configure System Time, Date Format, Separator, and Time Format as needed.

12.2: Wireless Settings

Region and channel settings are pre-configured and should not be altered. These settings must comply with relevant laws.

12.3: Reset

Restores system parameters to factory defaults. This function is not recommended for regular use. Contact the supplier for assistance if a reset is necessary.

12.4: Version Information

System: XM530_BMS50X20-WVGA_16M_20200612
Build Date: 2020-08-12 10:50:12
MAC: 00-01-02-03-04-00
Serial Number: 697af20a2af6a047

13. Video Recording

From the main menu, select the 'Record' icon ( ). Choose the recording file duration: 0.5Hr, 1Hr, or 2Hr.
Select 'OFF' if recording is not needed.
Ensure the date and time are set correctly to your local time before recording.
Insert the TF card when the monitor is powered off. Format the TF card when prompted on the first use. Press OK to format for automatic recording.

14. Video Playback

Access the main menu, select the 'Playback' icon ( ), and choose the desired video playback time.
The camera records at a resolution of 1920x1080. Due to system limitations, playback resolution is 800x480.

15. Installation Steps

Drill a hole in the wall and insert a wall plug.
Secure the mounting bracket to the wall using screws.
Attach the camera to the bracket and adjust the angle.

Questions and Answers:

Q: The LCD monitor does not display the camera?
A: 1. Check if the camera is powered on. 2. If the camera is powered on, reset the camera to factory settings and re-add it following step 4.1.
Q: There is annoying sound when using the talk function at close range?
A: This is normal due to proximity (within 2 meters). Adjust the monitor volume down or increase the distance between the camera and monitor.
Q: The monitor battery drains quickly?
A: 1. If Dormant mode is not enabled, the monitor runs continuously, draining the battery faster. Use Dormant mode (30S or 60S) to conserve battery. 2. Lowering the screen brightness can also extend standby time.
Q: The transfer distance between the camera and monitor is limited?
A: In an open environment, the transfer distance can reach up to 300 meters. Indoor use may be affected by interference from walls and other wireless electronic devices.

After-sales Instructions:

Refer to the actual product; all instructions are for reference only.
Product features may be updated without prior notice.
This manual covers basic functions; users are encouraged to explore further.
Contact the supplier promptly if any issues arise during product use.
While efforts have been made to ensure accuracy, some data may differ from the actual product. In case of discrepancies, the company's final explanation prevails.

FCC Caution:

§ 15.21 Information to user.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

§ 15.105 Information to the user.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF warning for Baby Camera: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
RF warning for Baby Monitor: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.