Altronix Home
Installation Guide for Altronix models including: HubSat8D Series, HubSat8D, HubSat82D, HubSat83D, Passive UTP Transceiver Hub with Integral Camera Power
Altronix HUBSAT8D | UTP Passive Transceiver Hub, 8 Channel,
File Info : application/pdf, 12 Pages, 1.06MB
DocumentDocumentVideo · Data · Power HubSat8D Series Passive UTP Transceiver Hub with Integral Camera Power Models Include: HubSat8D - Eight (8) Channel Passive UTP Transceiver Hub with Integral Camera Power HubSat82D - Eight (8) Channel Passive UTP Transceiver includes eight (8) HubWayAv Video Balun/Combiners HubSat83D - Eight (8) Channel Passive UTP Transceiver includes eight (8) HubWayDv Video Balun/Combiners Installation Guide Rev. 112508 More than just power.TM Installing Company: _______________ Service Rep. Name: __________________________________ Address: _____________________________________________ Phone #: __________________ Table of Contents: Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Additional Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Installation Instructions HubSat8D Passive UTP Transceiver Hub with Integral Camera Power. . . . . . . . . . . . . . . . . . . . pg. 3 HubSat8D for Use as a Remote Accessory Module with HubWay/HubWayLD/HubWayLDH UTP Transceiver Hubs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 4 Alternate 24VAC Fixed Camera Hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 5 HubSat Circuit Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 6 HubWayAv, HubWayAv2, HubWayDv, and HubWayDvi Video Balun/Combiners . . . . . . . . . . . pg. 7 CAT-5 Structured Cable Wiring Color Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 7 Typical Application Drawings HubSat8D Passive UTP Transceiver Hub with Integral Camera Power. . . . . . . . . . . . . . . . . . . . pg. 9 HubSat8D Remote Accessory Module with HubWay UTP Transceiver Hubs. . . . . . . . . . . . . . . . pg. 9 Enclosure Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 12 - 2 - HubSat8D Installation Guide Overview: Altronix HubSat8D Passive UTP Transceiver Hub with Integral Camera Power transmits UTP video, RS422/RS485 data and power over a single CAT-5 or higher structured cable. Unit provides 8 camera channels in a wall mount enclosure. Video transmission range is up to 750 ft. max. per channel. Units are compatible with AC and/or DC fixed or PTZ cameras when utilizing Altronix HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/ Combiners. In addition, the unit features individually selectable 24VAC or 28VAC PTC protected outputs with surge suppression. Optionally, the HubSat8D can be used as an accessory module to transmit video from up to 8 cameras over two (2) separate CAT-5 or higher structured cables back to the HubWay, HubWayLD or HubWayLDH Passive and Active UTP Transceiver Hubs. In addition, the HubSat8D provides power to these cameras locally to eliminate the possibility of voltage drop associated with long cable runs. Specifications: Agency Listings: Power (cont.): · UL Listed for Commercial CCTV Equipment · Unit provides up to 1A max. per channel not to (UL 2044). exceed a total of 8A maximum current. cUL Listed - CSA Standard C22.2 No.1-04, · PTC protected outputs are rated @ 1A per channel. Audio, Video and Similar Equipment. · Surge suppression. · CE European Conformity Visual Indicators: Input: · Eight (8) power LED indicators. · 115VAC 60Hz, 2.5A. · Primary in-line fuses are rated @ 3.5A/250V. Enclosure Dimensions (H x W x D approx.): 13.5" x 13" x 3.25" Video: (342.9mm x 330.2mm x 82.6mm) · Eight (8) channels of quality video over twisted pair Optional Accessories: up to a distance of 750 ft. per channel. · Video Balun/Combiners: · Eight (8) 75 Ohm video outputs. - HubWayAv: for use with 24VAC cameras. Data: - HubWayAv2: for use with 24VAC cameras. · RS422/RS485 data input. - HubWayDv: for use with 12VDC cameras. Power: · Individually selectable 24VAC or 28VAC power - HubWayDvi: for use with non-isolated 12VDC cameras. outputs with OFF position. Additional Models: HubSat82D · HubSat8D with eight (8) HubWayAv Video Balun/Combiners for 24VAC Cameras. HubSat83D · HubSat8D with eight (8) HubWayDv Video Balun/Combiners for 12VDC Cameras. WARNING: To reduce the risk of fire or electric shock do not expose the unit to rain or moisture. This installation should be made by qualified service personnel and should conform to all local codes. Installation Instructions: HubSat8D Passive UTP Transceiver Hub with Integral Camera Power. 1. Mount unit in desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure's upper keyholes over the two upper screws; level and secure. Mark the position of the lower two holes. Remove the enclosure. Drill the lower holes and install two fasteners. Place the enclosure's upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 12). Secure green wire lead to earth ground. 2. Set illuminated master power disconnect circuit breaker to the [OFF] position (Fig. 4a, pg. 8). 3. Connect 115VAC 60Hz to the black and white flying leads of the open frame transformer. Secure ground wire (Green) to earth ground (Fig. 4, pg. 8). 4. Select 24VAC or 28VAC power output for each of the Channels 1-4 on HubSat Circuit Board A and HubSat Circuit Board B (Fig. 4, pg. 8) with the corresponding output voltage switches. Select OFF position when servicing or installing individual cameras (Fig. 1d, pg. 6). 5. Connect the BNC video outputs marked [Video 1-4] on Circuit Board A and [Video 1-4] on Circuit Board B to the corresponding video inputs on the head end equipment (DVR) (Fig. 1a, pg. 6). HubSat8D Installation Guide - 3 - 6. Connect terminals marked [+ DATA ] on Circuit Board A and Circuit Board B (polarity must be observed) to the RS422/RS485 output of the head end equipment (DVR) (Fig. 1f, pg. 6). Note: The Data input terminals of Circuit Board A and Circuit Board B must be wired in parallel for proper operation. When using fixed cameras disregard this step. 7. Plug the RJ45 connector at one end of the CAT-5 or higher structured cable into the RJ45 jack marked [PVD1] on Circuit Board A (Fig. 1i, pg. 6). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1. · For 24VAC cameras use Altronix model HubWayAv/HubWayAv2 Video Balun/Combiner (Fig. 2a, 2b, 2e, pg. 7). · For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner (Fig. 2c, 2d, pg. 7). · For non-isolated 12VDC cameras use Altronix model HubWayDvi Video Balun/Combiner(Fig. 2c, 2d, pg. 7). The total cable distance must not exceed 750 ft. for video transmission between the HubSat8D and each camera. Repeat this step for all other camera channels [PVD2-4] on Circuit Board A and [PVD1-4] on Circuit Board B. 8. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 8). Power LEDs (Green) of the HubSat8D will illuminate when AC power is present (Fig. 1e, pg. 6) and HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiner LEDs will illuminate indicating power is present (Fig. 2b, 2d, pg. 7). 9. Measure the output voltage at each Video Balun/Combiner (Fig. 2b, 2d, pg. 7) before making connections to each camera to ensure proper operation and avoid possible damage. 10. Set illuminated master power disconnect circuit breaker to the [OFF] position (Fig. 4a, pg. 8). 11. Connect power outputs of HubWayAv, HubWayAv2 HubWayDv or HubWayDvi Video Balun/Combiners to power inputs of cameras (Fig. 2a-2e, pg. 7). Polarity must be observed. · HubWayAv/HubWayAv2 - Terminals marked [AC POWER] (Fig. 2a, 2b, 2e, pg. 7). · HubWayDv/HubWayDvi - Terminals marked [ 12VDC +] (Fig. 2c, 2d, pg. 7). 12. Connect the terminals marked [+ DATA ] of HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners to data input terminals of cameras for PTZ control (Fig. 2a-2e, pg. 7). Polarity must be observed. When using fixed cameras disregard this step. 13. Connect the BNC connector of HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners to the BNC video outputs of cameras (Fig. 2a-2e, pg. 7). 14. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 8). 15. The power LEDs (Green) of the HubSat8D will illuminate when AC power is present (Fig. 1e, pg. 6). Note: If any of the power LEDs are not illuminated, the cause may be due to the following: a. AC mains fail. b. Illuminated master power disconnect circuit breaker is tripped. c. One or both primary in-line fuse(s) are blown. Note: Replace fuse with same type and rating: Primary In-line Fuse Primary in-line fuses are rated @ 3.5A/250V (Fig. 4b, pg. 8). d. An individual power output voltage switch is set to the OFF position (Fig. 1d, pg. 6). e. A PTC is tripped due to a short circuit or overload condition for one or more channels/power outputs. To reset the PTC: 1. Set the voltage output selector switch for that corresponding channel to the OFF position. Switch must remain in the OFF position for approximately 2 minutes in order for the PTC to reset (Fig. 1d, pg. 6). 2. Eliminate the trouble condition (short circuit or overload). 3. Set the voltage output selector switch for either 24VAC or 28VAC (Fig. 1d, pg. 6). HubSat8D for use as a Remote Accessory Module with HubWay/HubWayLD/HubWayLDH UTP Transceiver Hubs. After completing steps 1-4 of Installation Instructions for HubSat8D Passive UTP Transceiver Hub with Integral Camera Power proceed with the following. 1. For fixed cameras run two (2) CAT-5 cables between HubSat8D and HubWay, HubWayLD or HubWayLDH to allow video transmission of up to eight (8) cameras. For PTZs run three (3) CAT-5 cables between HubSat8D and HubWay, HubWayLD or HubWayLDH (Fig. 6, pg. 9). a. Connect one (1) of the CAT-5 cables to the RJ45 jack marked [Video 1-4] on Circuit Board A. Connect the opposite end of this CAT-5 cable into the RJ45 jack marked [CH 1-4] of HubWay, HubWayLD or HubWayLDH unit (Fig. 6, pg. 9). - 4 - HubSat8D Installation Guide b. Connect the second CAT-5 cable to the RJ45 jack marked [Video 1-4] on Circuit Board B. Connect the opposite end of this CAT-5 cable into the RJ45 jack marked [CH 5-8] of HubWay, HubWayLD or HubWayLDH unit (Fig. 6, pg. 9). c. For data (PTZ) connect the third CAT-5 cable to the RJ45 jack marked [Data 1-4] on Circuit Board A. Connect the opposite end of this CAT-5 cable into any unused RJ45 jack marked [1-16] of HubWay, HubWayLD or HubWayLDH unit (Fig. 6, pg. 9). Note: Data inputs of HubWay, HubWayLD or HubWayLDH units must be wired in parallel for proper operation. When using fixed cameras disregard this step. 2. Plug the RJ45 connector at one end of the CAT-5 or higher structured cable into the RJ45 jack marked [PVD1] on Circuit Board A (Fig. 1i, pg. 6). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1. · For 24VAC cameras use Altronix model HubWayAv/HubWayAv2 Video Balun/Combiner (Fig. 2a, 2b, 2e, pg. 7). · For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner (Fig. 2c, 2d, pg. 7). · For non-isolated 12VDC cameras use Altronix model HubWayDvi Video Balun/Combiner (Fig. 2c, 2d, pg. 7). The total cable distance must not exceed 750 ft. for video transmission between the HubSat8D and each camera. Repeat this step for all other camera channels [PVD2-4] on Circuit Board A and [PVD1-4] on Circuit Board B. 3. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 8). Power LEDs (Green) of the HubSat8D will illuminate when AC power is present (Fig. 1e, pg. 6) and HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiner LEDs will illuminate indicating power is present (Fig. 2b, 2d, pg. 7). 4. Measure the output voltage at each Video Balun/Combiner (Fig. 2b, 2d, pg. 7) before making connections to each camera to ensure proper operation and avoid possible damage. 5. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 4a, pg. 8). 6. Connect power outputs of HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners to power inputs of cameras (Fig. 2a-2d, pg. 7). Polarity must be observed. · HubWayAv/HubWayAv2 - Terminals marked [AC POWER] (Fig. 2a, 2b, 2e, pg. 7). · HubWayDv/HubWayDvi - Terminals marked [ 12VDC +] (Fig. 2c, 2d, pg. 7). 7. Connect the terminals marked [+ DATA ] of HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners to data input terminals of cameras for PTZ control (Fig. 2a-2e, pg. 7). Polarity must be observed. When using fixed cameras disregard this step. 8. Connect the BNC connector of HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/ Combiners to the BNC video outputs of cameras (Fig. 2a-2e, pg. 7). 9. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 8). 10. The power LEDs (Green) of the HubSat8D will illuminate when AC power is present (Fig. 1e, pg. 6). Note: If any of the power LEDs are not illuminated, the cause may be due to the following: a. AC mains fail. b. Illuminated master power disconnect circuit breaker is tripped. c. One or both primary in-line fuse(s) are blown. Note: Replace fuse with same type and rating: Primary In-line Fuse Primary in-line fuses are rated @ 3.5A/250V (Fig. 4b, pg. 8). d. An individual power output voltage switch is set to the OFF position (Fig. 1d, pg. 6). e. A PTC is tripped due to a short circuit or overload condition for one or more channels/power outputs. To reset the PTC: 1. Set the voltage output selector switch for that corresponding channel to the OFF position. Switch must remain in the OFF position for approximately 2 minutes in order for the PTC to reset (Fig. 1d, pg. 6). 2. Eliminate the trouble condition (short circuit or overload). 3. Set the voltage output selector switch for either 24VAC or 28VAC (Fig. 1d, pg. 6). HubSat8D Installation Guide - 5 - Alternate 24VAC Fixed Camera Hookup (Fig. 6a, pg. 9). After completing steps 1-5 of Installation Instructions Remote Accessory Module for use with HubWay, HubWayLD or HubWayLDH UTP Transceiver Hubs proceed with the following. 1. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 4a, pg. 8). 2. Connect one end of the coaxial cable to the BNC connector marked [Video1] on Circuit Board A (Fig. 1a, pg. 6). Connect the opposite end of the coaxial cable to the BNC video output of camera 1 (Fig. 6a, pg. 9). 3. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 8). Measure the output voltage at terminal pair marked [AUX1] on Circuit Board A to ensure proper operation and avoid possible damage (Fig. 1b, pg. 6). 4. Connect the power output terminal pair marked [AUX1] on Circuit Board A to the power inputs of camera 1(Fig. 1c, pg. 6). Repeat steps 1-3 for each additional camera [AUX2-4]. Fig. 1 - HubSat Circuit Board 1c 1b 1c 1d 28VAC AUX1 AUX2 28VAC 28VAC AUX3 AUX4 28VAC OFF OFF OFF OFF 24VAC VIDEO1 1a 24VAC 24VAC VIDEO2 VIDEO3 24VAC 1e VIDEO4 + DATA - 1f 1i PVD1 PVD2 DATA 1-4 1h VIDEO 1-4 1g PVD3 PVD4 1a - BNC Connector: Video in from remote camera video out to DVR. 1b - Output PTCs: Protects each output. 1c - Power Terminals: 24VAC/28VAC power outputs. 1d - Output Voltage Switches: Selects 24VAC/28VAC/OFF for each output. 1e - LED(s) 1-4: Power output indicators. 1f - Data: RS422/RS485 input from head end equipment (DVR) for PTZ control. 1g - Channels 1-4: Single CAT-5 or higher structured cable out to HubWay, HubWayLD or HubWayLDH enables transmission of up to four (4) video signals. Pin out configuration (Fig. 4, pg. 7). 1h - Data: CAT-5 or higher structured cable to data port on HubWay, HubWayLD or HubWayLDH or head end equipment (DVR). 1i - Channels 1-4: CAT-5 or higher structured cable to cameras. Pin out configuration (Fig. 3, pg. 7). - 6 - HubSat8D Installation Guide HubWayAv, HubWayAv2, HubWayDv, and HubWayDvi Video Balun/Combiners: Altronix Model Number HubWayAv HubWayAv2 HubWayDv HubWayDvi Input Voltage from HubWay Unit *24VAC/28VAC *24VAC/28VAC *24VAC/28VAC *24VAC/28VAC Output Voltage to Camera *24VAC/28VAC *24VAC/28VAC 12VDC 12VDC electronically isolated *Based on camera load and structured cable length. Fig. 2 Camera Type *24VAC/28VAC *24VAC/28VAC 12VDC cameras 12VDC cameras without isolation Power LED Green N/A Red Red Fig. 2a VIDEO HubWayAv VIDEO BALUN/COMBINER CAT5 AC +DATA-- POWER Fig. 2c VIDEO HubWayDv VIDEO BALUN/COMBINER CAT5 +DATA-- -- 12VDC+ * Also Available as: HubWayDvi Video Balun/ Combiner for non-isolated 12VDC cameras Fig. 2b RJ45 Jack Wire Connectors Fig. 2d RJ45 Jack Wire Connectors To BNC Connector of Camera Structured Cable from HubWay8CD or HubWay16CD Fig. 2e - HubWayAV2 Cat5 back to HubWay or HubSat Green Power LED AC Power to Camera -- Data to + Camera To BNC Connector of Camera Structured Cable from HubWay8CD or HubWay16CD Power to Camera Data to Camera Red Power LED + 12VDC Power -- to Camera -- Data to + Camera HubWayAv/HubWayAv2 passes AC voltage from pins 4, 5, 7, 8 to terminals marked [AC Power] (Fig. 3, pg. 7). Video from Camera HubWayDv/HubWayDvi converts AC voltage to DC voltage from pins 4, 5, 7, 8 to terminals marked [ 12VDC +] (Fig. 3, pg. 7). Fig. 3 - CAT-5 Structured Cable Wiring Color Codes and PIN Configurations PVD1-4 on HubSat8D and Video Balun/Combiner 1 - White/Orange [VIDEO +] 2 - Orange [VIDEO ] 3 - White/Green [DATA +] 4 - Blue [AC 1] 5 - White/Blue [AC 2] 6 - Green [DATA ] 7 - White/Brown [AC 2] 8 - Brown [AC 1] HubSat8D Installation Guide - 7 - Fig. 4 Fig. 4a - Illuminated master power disconnect circuit breaker: · OFF position: circuit breaker tripped Switch not illuminated. · RESET (ON) position Switch illuminated. Input 115VAC, 60Hz - 8 - Green Lead (ground) Fig. 4b Primary In-line fuses: Rated @ 3.5A/250V HubSat8D Installation Guide Typical Application Drawing HubSat8D Passive UTP Transceiver Hub with Integral Camera Power: Fig. 5 Head End Equipment (DVR) RS485 Monitor Data Data Video Power 12VDC PTZ Camera 12VDC Fixed Camera BNC CAT-5 HubWayD Video Balun Combiner Video Power CAT-5 HubWayD Video Balun Combiner CAT-5 Data Video Power HubWayA Video Balun Combiner 24VAC PTZ Camera 24VAC/28VAC Camera Power Provided by HubSat8D 115VAC Input, 60Hz CAT-5 HubWayA Video Balun Combiner Video Power (4) Additional Fixed or PTZ Cameras 24VAC Fixed Camera Typical Application Drawing HubSat8D Remote Accessory Module with HubWay UTP Transceiver Hubs: Fig. 6 Data To Head End Equipment (DVR) Video Out To Head End Equipment (DVR) 1 2 3 4 CH 1-4 5 6 7 8 CH 5-8 DATA 1-8 28VAC OFF 24VAC Data Video Power Data (CAT-5) or Twisted Pair CAT-5 Four (4) Video signals over a single CAT-5 Four (4) Video signals over a single CAT-5 HubWayD Video Balun 12VDC Combiner PTZ Camera Data Video Power HubWayD Video Balun 12VDC Combiner PTZ Camera CAT-5 CAT-5 Video Power 12VDC Fixed Camera HubWayD Video Balun Combiner 24VAC/28VAC Camera Power Provided by HubSat8D 115VAC Input, 60Hz CAT-5 Data Video Power HubWayA Video Balun Combiner Video connections on rear of unit 24VAC PTZ Camera Coax Power 24VAC Fixed Camera Coax Power Coax Power 24VAC Fixed Camera Coax Power 24VAC Fixed Camera 24VAC Fixed Camera Fig. 6a - Alternate 24VAC fixed camera hookup. HubSat8D Installation Guide - 9 - Notes: - 10 - HubSat8D Installation Guide Notes: HubSat8D Installation Guide - 11 - The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of an insulated DANGEROUS VOLTAGE within the product's enclosure that may be of sufficient magnitude to constitute an electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION: To reduce the risk of electric shock do not open enclosure. There are no user serviceable parts inside. Refer servicing to qualified service personnel. Enclosure Dimensions (H x W x D approximate): 13.5" x 13" x 3.25" (342.9mm x 330.2mm x 82.6mm) 1.40" (35.6mm) 4.85" (123.2mm) 4.85" (123.2mm) 1.40" (35.6mm) 1.20" (30.5mm) 3.25" (82.6mm) 1.20" (30.5mm) 1.40" (35.6mm) 0.75" (19.1mm) 12.5" (317.5mm) 11.0" (279.4mm) 0.75" (19.1mm) 0.9375" (23.8mm) 1.20" (30.5mm) 1.40" (35.6mm) 5.10" (129.5mm) 5.10" (129.5mm) 13.0" (330.2mm) 6.5625" (166.7mm) 5.10" (129.5mm) 3.25" (82.6mm) 0.9375" (23.8mm) 3.25" (82.6mm) 3.25" (82.6mm) 1.0" (25.4mm) 1.0" (25.4mm) 10.5" (266.7mm) 1.0" (25.4mm) Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 website: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty IIHubSat8D K18U MEMBER - 12 - HubSat8D Installation Guide