User Guide for AzureWave models including: AW-CU300AV3-USB, WLAN Microcontroller Module with Type-C Dongle
https://docs.aws.amazon.com/iot/latest/developerguide/iot-gs.html. But, if you want to setup AzureWave AWS Connector, you would just refer to ...
1 dic 2020 — Plug the AW-CU300AV3-USB dongle into the USB type C port or through an USB type A male to USB type C female adapter (not included in the box) if the ...
File Info : application/pdf, 21 Pages, 1.79MB
DocumentDocumentAW-CU300AV3-USB IEEE 802.11 b/g/n WLAN Microcontroller Module with Type-C Dongle Getting Started Guide Rev. 0.1 1 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. Revision History Version Revision Date Description 0.1 2020/12/01 Initial version Initials Renton Tao Jackson Boon Approved N.C. Chen S.C Chueh 2 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. Table of Contents 1. Hardware Specification ............................................................................................................. 4 2. Hardware Setup ......................................................................................................................... 5 2.1 Components......................................................................................................................................................5 2.2 Identify the Hardware and Firmware.................................................................................................................7 3. AWS Command Example .......................................................................................................... 9 3.1 Getting Started with AWS IoT Core ..................................................................................................................9 3.2 Publish and Monitor MQTT message on the cloud ........................................................................................13 4. Block Diagram and Schematic ............................................................................................... 15 4.1 Block Diagram for AW-CU300AV3-USB ........................................................................................................15 4.2 Schematics for AW-CU300AV3-USB .............................................................................................................16 4.3 Block Diagram for Arduino Uno Adaptor ........................................................................................................19 4.4 Schematics for Arduino Uno Adaptor .............................................................................................................19 5. Additional Information ............................................................................................................ 21 3 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. 1. Hardware Specification Powerful MCU USB Type-C male Plug SPI Flash Printed Antenna Top side Bottom side 8-Pin header 4 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. 2. Hardware Setup 2.1 Components Plug the AW-CU300AV3-USB dongle into the USB type C port or through an USB type A male to USB type C female adapter (not included in the box) if the computer does not have the USB type C port or it can not recognize the dongle USB type A male to USB type C female adapter Remove all the jumpers (2mm pitch) on the dongle before mating it with the Arduino Uno through the ARDUINO UNO ADPAPTOR. The digital logic level & power supply input of the dongle are 3.3V. DO NOT directly connect the dongle to the Arduino Uno. 5 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. ARDUINO UNO ADPAPTOR AW-CU300AV3-USB connected to Arduino Uno through the ARDUINO UNO ADPAPTOR 6 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. 2.2 Identify the Hardware and Firmware Check if Device Manager can recognize AW-CU300AV3-USB. If not, download FTDI Driver at https://www.ftdichip.com/Drivers/VCP.htm, then send the AT commands through the second FTDI com port Open a serial connection by using PuTTY or the similar terminal emulator 7 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. To force the terminal show characters you type and send the command only after you hit the "Enter" key, set Local echo & Local line editing to "Force on" Type AT+MOD_About and hit "Enter" key to identify the dongle hardware and firmware 8 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. 3. AWS Command Example Please find the command details in AWS CONNECTOR AT Command Set. Below are commands for the demo: 1. Turn on Wi-Fi module: AT+WIFI_On 2. Retrieve the Wi-Fi AP | Station Mode: AT+WIFI_GetMode 3. Perform a Wi-Fi network scan: AT+WIFI_Scan 4. Set and store the Wi-Fi AP information when AW-CU427-USB in Station Mode: AT+WIFI_SetAP=SSID,password,security type SSID: SSID of AP (case sensitive) password: password for AP (case sensitive) security type: OPEN | WEP | WPA | WPA2 5. Connect to the AP: AT+WIFI_Connect 6. Define and store Thing-specific configuration: AT+THING_Set=client ID,endpoint,root CA certificate,client certificate,client private key client ID: Thing name(Client ID) endpoint: AWS IoT endpoint URL root CA certification: Certificate for root CA client certificate: Certificate for this Thing client private key: Private key for thing Thing 7. Connect the client to MQTT broker: AT+MQTT_Connect 8. Subscribe to and save MQTT topic: AT+MQTT_Subscribe=<topic>,<qos> 9. Publish to MQTT topic: AT+MQTT_Publish=topic,message,qos topic: Topic to publish to message: Message to publish qos: 0 | 1 3.1 Getting Started with AWS IoT Core Step 0: The below link is a documents of how to setup AWS IOT console, you can refer to it for full AWS IOT knowledge. https://docs.aws.amazon.com/iot/latest/developerguide/iot-gs.html But, if you want to setup AzureWave AWS Connector, you would just refer to the following steps. 9 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. Step 1: Create AWS Account, Create an IAM user. Please refer to the below link to setup AWS Account and IAM user. https://docs.aws.amazon.com/iot/latest/developerguide/setting-up.html If you have created an IAM user, please refer to the following setting to connect these two policies (AmazonFreeRTOSFullAccess, AWSIoTFullAccess) to your IAM. https://docs.aws.amazon.com/freertos/latest/userguide/freertos-account-and-permissions.html Step 2: Create a thing. A thing represents a specific device or instance that can communicate with AWS IOT. Please refer to the following link to create a thing. https://docs.aws.amazon.com/iot/latest/developerguide/create-aws-thing.html Step 3: Register a device This step will create certificate and private key. You can use certificate, private key, thing name and endpoint as AT+THING_Set command parameter. After this command executing, the four parameter will be provision to our connector. After provisioning, you can connect AWS IOT with MQTT or SHADOW operation. Please refer to the steps as the following link. https://docs.aws.amazon.com/iot/latest/developerguide/register-device.html After finishing the steps, please notice the following two actions: Download certificate and private key In Create and activate a device certificate chapter, please download and keeps the certificate and private key. Because they will be used when send AT+THING_Set command. 10 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. Thing Name and Endpoint These two data will also be used for AT+THING_Set command. You can find out thing name in Manage > Things submenu, and endpoint in settings of AWS IOT dashboard. 11 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. 12 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. 3.2 Publish and Monitor MQTT message on the cloud Step 0: Make sure the AP under test is connected to the internet using other Wi-Fi enabled devices. Assume the SSID, password and security type of the AP is MySSID, MyPassword, wpa2. Step 1: Connect the AW-CU427-USB to the system (refer to 2. Hardware Setup) and turn off the wireless devices near the AW-CU427-USB (except for the device under test). Turn on the Wi-Fi module of the AW-CU427-USB using AT+WIFI_On Step 2: Check if AW-CU427-USB is in station mode using AT+WIFI_GetMode Step 3: Set and store information of the AP using AT+WIFI_SetAP= MySSID,MyPassword,wpa2 AT+WIFI_SetAP=SSID,password,security type SSID: SSID of AP (case sensitive) password: password for AP (case sensitive) security type: OPEN | WEP | WPA | WPA2 Step 4: Connect to the AP: AT+WIFI_Connect Step 5: Define and store Thing-specific configuration using AT+THING_Set command AT+THING_Set=client ID,endpoint,client certificate,client private key client ID: Thing name(Client ID) endpoint: AWS IoT endpoint URL client certificate: Certificate for this Thing (downloaded in 3.1 step 3) client private key: Private key for this Thing (downloaded in 3.1 step 3) You should create command as format below: AT+THING_Set=98c6, a25giitjes2mei-ats.iot.ap-northeast-1.amazonaws.com, -----BEGIN CERTIFICATE-----\n...base64 data...\n-----END CERTIFICATE-----\n, -----BEGIN RSA PRIVATE KEY-----\n...base64 data...\n-----END RSA PRIVATE KEY-----\n Step 6: Connect the client to MQTT broker: AT+MQTT_Connect. Step 7: Subscribe to and save MQTT topic using AT+MQTT_Subscribe=iotdemo/1,0 Step 8: Publish to MQTT topic using AT+MQTT_Publish=iotdemo/1, hello, 0 AT+MQTT_Publish=topic,message,qos topic: Topic to publish to 13 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. message: Message to publish qos: 0 | 1 Step 9: Use the MQTT client in the AWS IoT console to monitor the messages that device sends to the AWS Cloud. Sign in to the AWS IoT console. https://console.aws.amazon.com/iotv2/ In the navigation pane, choose Test to open the MQTT client. In Subscription topic, enter iotdemo/#, and then choose Subscribe to topic. You should see the message send from device as like below. 14 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. 4. Block Diagram and Schematic 4.1 Block Diagram for AW-CU300AV3-USB 15 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. 4.2 Schematics for AW-CU300AV3-USB 16 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. 17 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. Module pinout (AW-CU300A V3) 18 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. 4.3 Block Diagram for Arduino Uno Adaptor 4.4 Schematics for Arduino Uno Adaptor 19 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. 20 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave. 5. Additional Information The AW-CU427-USB is designed for Engineering Evaluation Purpose Only as opposed to an end product. Thus, it may not comply with directives such as WEEE, CE and FCC. The dongle is not completely enclosed with a shielding case. User must take whatever measures to prevent ESD and minimize interference generated by the dongle. For preventing any damage on this dongle, please plug it into USB female port horizontally. 21 The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave.
console.aws.amazon.com/iotv2/
First steps - FreeRTOS First steps - FreeRTOSHow to manage things with the registry - AWS IoT Core How to manage things with the registry - AWS IoT CoreGetting started with AWS IoT Core tutorials - AWS IoT CoreHow to manage things with the registry - AWS IoT Core How to manage things with the registry - AWS IoT CoreSet up AWS account - AWS IoT Core
VCP Drivers - FTDI