ASKO Spare Parts Catalogue

Base and Related Parts

Diagram showing base and related parts of the ASKO D5424 ADA US dishwasher.

Baskets and Related Parts

Diagram showing baskets and related parts of the ASKO D5424 ADA US dishwasher.

Wash System

Diagram showing the wash system components of the ASKO D5424 ADA US dishwasher.

Bottom Well and Related Parts

Diagram showing bottom well and related parts of the ASKO D5424 ADA US dishwasher.

Inner Door, Panel and Related Parts

Diagram showing inner door, panel and related parts of the ASKO D5424 ADA US dishwasher.

Control Panel and Related Parts

Diagram showing control panel and related parts of the ASKO D5424 ADA US dishwasher.

Circuit Diagram

Circuit diagram for DW90.1, DW90.1OEM, DW90.2, DW90.C, DW90.3 models. Includes component descriptions and resistances.

Resistances at Room Temperature (CA. 20°C/68°F)

• RADIO INTERFERENCE SUPPRESSION FILTER: 1 MOHM
• HEATING ELEMENT 1200W 120V: 12 OHM
• HEATING ELEMENT 1600W 230V: 32 OHM
• HEATING ELEMENT 2040W 230V: 25 OHM
• THERMISTOR: 60 KOHM
• COMBINED DISPENSER 120V: 0,28 KOHM
• COMBINED DISPENSER 230V: 1,32 KOHM
• CIRCULATION PUMP 120V 60HZ: 32 OHM
• CIRCULATION PUMP 230V 50HZ: 110 OHM
• CIRCULATION PUMP 220V 60HZ: 56 OHM
• DRAIN PUMP 120V 60HZ: 25 OHM
• DRAIN PUMP 230V 50HZ: 150 OHM
• DRAIN PUMP 230V 60HZ: 85 OHM
• SPRAY ARM DIVIDER 120V 60HZ: 2.6 KOHM
• SPRAY ARM DIVIDER 230V 50/60HZ: 8,5 KOHM
• INLET VALVE SINGLE INCL. 120V: 0.95 ΚΟΗΜ
• INLET VALVE SAFETY INCL. 120V: 0.5 KOHM
• INLET VALVE SINGLE INCL. 230V: 3,9 KOHM
• INLET VALVE SAFETY INCL. 230V: 2 KOHM
• SALT VALVE 120V: 0,65 KOHM
• MIX VALVE 120V: 0,65 KOHM
• SALT VALVE 230V: 3 KOHM
• MIX VALVE 230V: 2,3 KOHM
• HALOGEN LAMP 5W 12V: <10 ΚΟΗΜ
• WAX MOTOR: 1.1 KOHM
• FAN MOTOR 120V: 0.18 ΚΟΗΜ
• FAN MOTOR 230V: 0,85 KOHM
• FAN MOTOR 2 120V: 0,22 ΚΟΗΜ
• FAN MOTOR 2 230V: 0,90 KOHM

Circuit Diagram Number: 80 840 68-01

Service Menu and Displays

Information on entering the service menu and details about the displays for different ASKO dishwasher models.

DW90.1, DW90.1 OEM, DW90.2 Service Menu

To enter service menu: After power on, wait until LCD is turned on. Then, within 5sec, press first T1 and directly after T2. Hold both buttons pressed during 5sec.

Failures:

• F:XX (Failure code)
• F42 Thermistor
• F43 Pressure sensor
• F44 Turbidity sensor
• F45 Diverter

Testing:

• d:01 Mix valve and inlet valve on (1 sec delay between mix valve and inlet valve)
• d:02 Inlet valve on
• d:03 Salt Valve on
• d:04 Combi dispenser on
• d:05 Circulation and spolarmsväxlaren (if available) shall alternate between positions 1 and 3 every 30 seconds
• d:06 Circulation and heaters - max 75 ° C
• d:07 Fan and vax actuator
• d:08 Drain Pump on
• d:00 No components on

Water inlet:

• P:0 Normal water intake, default
• P:5 Water intake increased +5%
• P:10 Water intake increased +10%
• P:15 Water intake increased +15%
• L:0 Time, flow meter disconnected, inlet time: no of pulses x 0.068 [s]
• L:5 Timed water intake increased +5%
• L:10 Timed water intake increased +10%
• L:15 Timed water intake increased +15%

Variant:

• U:1 DW90.1 Variant 1 and 2, the default setting (temperature, drying)
• U:2 DW90.1 OEM Variant 1 and 2, the default setting (temperature, drying)
• U:3 DW90.1 Variant 3 and 4 (Temperature, Drying, Delayed Start)
• U:4 DW90.1 OEM Variant 3 and 4 (Temperature, Drying, Delayed Start)
• U:5 DW90.1 Variant 5 and 6 (Set of time program, Temperature, Drying, Time saving, Delayed Start)
• U:6 DW90.1 OEM Variant 5 and 6 (Set of time program, Temperature, Drying, Time saving, Delayed Start)
• U:7 DW90.1 and DW90.1OEM Variant 7 (Set of time program, Temperature, Drying, Time-saving, Upper Lower basket wash, Delayed Start)

DW90.3 Service Menu

To enter service menu: Press T1 and T2 at power on.

Control unit manufacturing date:

• CU Date code xxxx
• Software version
• Software xxX

Last failure read out:

• F10 Overfillig
• F11 Drain
• F12 Water inlet
• F40 Valve leakage
• F41 Temp.
• 3 FAIL. XXXX
• 2 FAIL. XXXX
• 1 FAIL. XXXX

Testing:

• Testing Valve A: XXX
• Testing Valve B: XXX
• Testing Salt
• Testing Cirk: XXV
• Testing Heater: XX°C
• Testing Fan: XXXX
• Testing TDE
• Testaing Drain: XXV

Water inlet:

• Water volume 0
• Water volume +5%
• Water volume +10%
• Water volume +15%
• Water volume Time 0
• Water volume Time +5%
• Water volume Time +10%
• Water volume Time +15%

Variant:

• U:1 DW90.2 Variant 1, the default setting (temperature, drying)
• U:2 DW90.2 Variant 2 (Temperature, Drying, Delayed Start)
• U:3 DW90.2 Variant 3 (Temperature, Drying, Delayed Start, Set of time program)
• U:4 DW90.2 Variant 4 (Temperature, Drying, Delayed Start, Set of time program, Time saving)

TDE & HWC, only DW90.2:

• A:0 Turbo Drying Express and Heat Water Circuit off, default setting
• A:1 Turbo Drying Express on
• A:2 Heat Water Circuit on

ECO, only DW90.1:

• E:0 ECO off, the default setting
• E:1 ECO on, when the machine is connected to hot water consumed less electrical energy to heat water and program time is shortened.

Super rinse:

• S:0 Super Rinse, default
• S:1 Super Rinse on. Adding two extra rinses.

Total restart:

• r:0 No restart on the next press T2, default
• r:1 Total restart at the next press T2

Fan sequence:

• Y:0 No fan sequence during wash cycle
• Y:1 Fan sequence during the wash cycle but not in Normal program, the default setting
• Y:2 Fan in sequence during the all wash cycles

Region:

• Region EU Region Europe, the default setting
• Region US Region USA
• Region AU Region Australia

DUO:

• DUO Off DUO Off
• DUO On DUO On, to activate program like Sani, Pots & pans

Displays

DW90.1 Display:

Diagram showing DW90.1 display with LEDs and push-buttons.

Panel type DW90.1, L = LED, T = Push-button

DW90.1 OEM Display:

Diagram showing DW90.1 OEM display with LEDs and push-buttons.

Panel type DW90.1 OEM, L = LED, T = Push-button

DW90.2 Display:

Diagram showing DW90.2 display with LEDs and push-buttons.

Panel type DW90.2, L = LED, T = Push-button

DW90.3 Display:

Diagram showing DW90.3 display with touch areas.

Panel type DW90.3, T Touch areas